FEZiBO 48 Inch Wood and Steel Computer Desk Instruction Manual

FEZiBO 48 Inch Wood and Steel Computer Desk

Caution

• Keep children and animals away from the desk during use. Ensure the desktop is not touching any walls.
• Remove obstacles taller than 20″/51 cm from underneath the desk.
• Operate only in a working environment temperature of 32°F-104°F/0°C-40°C.
• Keep product away from corrosive gases, liquids and dusty objects.
• Keep hands, feet and other body parts in a safe position during operation. Anti-collision is not automatically enabled during all resets.
• Please read the following instructions carefully before using the height-adjustable desk.
• The company does not bear any warranty or liability for damage and human injury caused by any abnormal or un-intended operation of the equipment.
• It is necessary to perform a manual reset after the initial installation or power cycling the equipment.

Parts & Tools

Installation

Overview

Note Please make sure that there are no obstacles during the lifting process of the table, the table is not close to the wall, and the length of the wire is enough for the table to move up and down.
Recommendation Preset the most comfortable height when you sit down as 1, the most comfortable height when you stand up as 2, and the remaining preset height can be freely set to another height.

Using Instruction

Phenomenon
After the controller reports an error, the digital display shows “E07-E09”. Even if it is powered on after de-energized, the error display remains, and all keys still do not work.

Reset method
Press and hold “Down” key for 5 seconds, and the digital display shows “RST”. Release the key and then press “Down” key to reset.

Setting of upper limit
Press “M” key, the digital display shows “S-” and release the key. Press and hold “Up” key, the digital display flashes once, and release the key. Press “M” key again and hold it for 2 seconds, and the digital display shows “999”. The upper limit setting is completed.

Setting of lower limit
Press “M” key, the digital display shows “S-” and release the key. Press and hold “Down” key, the digital display flashes once, and release the key. Press “M” key again and hold it for 2 seconds, and the digital display shows “000”. The lower limit setting is completed.

Cancellation of limit
Press “M” key, the digital display shows “S-” and release the key. Press “M” key again and hold it for 2 seconds, and the digital display shows “555”. The upper and lower limit settings are deleted.

Locking
Press for 3 seconds, the digital display shows “LOC”, and manual controller keys are locked.
Unlocking
Press for 3 seconds, the digital display shows digits, and manual controller keys are unlocked.

Adjustment of minimum height value
In the reset state, that is, the digital display shows “RST”. Press and hold “M” key for 5 seconds, and the digital display shows the default value after reset, and flashes on and off.
Press “Up” key or “Down” key to adjust to the required height value. After releasing the key for 5 seconds, the digital display shows “RST” and the adjustment is successful.

Switching of inching with memory/continuous movement with memory
In the reset state, that is, the digital display shows “RST”.
Press and hold “1” key for 5 seconds to switch the mode between inching with memory and continuous movement with memory. The digital display shows “10.1”, and the continuous movement mode starts from the memory position.
The digital display shows “10.2”, and the inching mode starts from the memory position.

Switching of display in cm/inch

• In the reset state, that is, the digital display shows “RST”.
• Press and hold the key “2” for 5 seconds to switch the display in inch or cm.
• The digital display shows “10.3”, and the height value is displayed in cm after reset.
• The digital display shows “10.4”, and the height value is displayed in inch after reset.

Selection of sensitivity to retreat when encountering obstacles
In the reset state, that is, the digital display shows “RST”.
Press and hold “Up” key for 5 seconds to change the sensitivity to retreat when encountering obstacles, and the digital display switches the display：
“10.5”-10kg
“10.6”-15kg
“10.7”-20kg

Setting of memory position
Press “M” key, the digital display shows “S-“, select and press one of the memory keys (numeric keys), and the current position will be remembered.
Use “UP” or “Down” key to adjust the table to the desired position, and then repeat the above manipulation.

Troubleshooting

Common problems and troubleshooting

1. The following problems may be solved by resetting the table:
   • Malfunction
   • The manual panel displays RES (reset)
   • Error messages, (E07, E08) are displayed on the manual control panel, but the motor drive wire is connected normally.
2. If the manual panel displays “HOT” (hot), please turn off the power and cool for 20 minutes.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>