SelectBlinds Cordless Roller Shade with PVC Valance Installation Guide

June 12, 2024
SelectBlinds

SelectBlinds Cordless Roller Shade with PVC Valance Installation Guide
SelectBlinds Cordless Roller Shade with PVC Valance

GETTING STARTED

IMPORTANT: The included screws can be screwed directly into wood. When attaching to drywall or metal, use anchors that are designed for such substrates. See your hardware store or supplier for guidance on appropriate anchors for your substrate

TOOLS NEEDED:

  • Pencil
  • Phillips head screwdriver
  • Tape measure
  • Power drill

PARTS INCLUDED

  • **2 LARGE SCREWS”

**

  • **2 SMALL SCREWS

**

  • **BRACKET  Select option that suits installation

**

STEP 1: POSITION TENSION DEVICE

The tension device must be installed to make the shade fully operable.

PROCEDURE: To begin installation, first slide the tension device to the bottom of the bead chain.

While holding the tension device in one hand, pull the plunger away from the bead chain with the other hand. Lift the bead chain out of the bead locking groove and slide the tension device to the piynger. bottom of the chain loop.

Pull the tension device down until the bead chain Bead is fully tensioned (plunger will be at the top) and locking then move the tension device up approximatelyls” groove (3mm).

Mark the screw hole locations on the wall with a pencil.

(STEP 2: MOUNT TENSION DEVICE

GENERAL NOTE: If mounting into wood, pre-drill screw holes and then install the tension device using the 2 large screws provided.

If not securing into wood, use appropriate anchors for the substrate and follow anchor manufacturer’s instructions.

USING A BRACKET: Align the mounting bracket sight holes with the pencil marks and fix the bracket.

Press the tension device onto the mounting bracket posts. Carefully install the 2 small screws provided, through the tension device into the mounting bracket using a Phillips head screwdriver.
DO NOT OVER-TIGHTEN.

  • **INSIDE MOUNT

**

  • OUTSIDE MOUNT
    MOUNT TENSION DEVICE

  • FLOOR MOUNT
    MOUNT TENSION DEVICE

  • SIDE MOUNT
    MOUNT TENSION DEVICE

FLOOR MOUNT INSTRUCTIONS:

Securely fix the floor mount bracket to desired location.

Assemble with chainhold & chain.

Adjust the length of the bead chain so that the plunger is%” (3mmJbelow its top position. Adjust chain length by removing balls and reassemble with pliers or a chain connector (sold separate).

Motorization Instructions

MOTOR: The side of the motor with the small (WHITE) button which is called the setting button JOG: When the motor oscillates and the blind moves up and down

A) TURNING ON THE MOTOR:

  1. Press the WHITE button on the motor head for 1 second until the motor beeps once.

B) INSTRUCTIONS FOR PAIRING THE MOTOR WITH REMOTE:

  1. Select the channel for the blind using the channel buttons (). This step does not apply to 1-channel remotes.
  2. Hold down the setting button (WHITE button) until it jogs 1 time and then release.
  3. Click the up (insert image here of up button) button. The blind will jog 1 time and the remote is now paired to the motor.

C) CHANGING THE BLIND DIRECTION:

  1. Press the up (A) button on the remote.
  2. IF THE BLIND GOES UP: jump to the next section “D”
  3. IF THE BLIND GOES DOWN: hold the stop (B) button until the blind jogs then press the down (V) button. The blind will jog again and the directions should have changed.

D) SET UP FOR THE LOWER LIMIT:

  1. After the motor direction is changed, flip the remote over and take out the white cap and click the SET button (top right-hand corner) and blind will jog once.
  2. Hold the down button until blind starts moving freely downwards and stop close to your desired bottom stop. Check the length with a measuring tape and adjust with help of up (A) and down (V) arrow.
  3. Once the lower limit is reached, click SET again and blind will jog once.
    Note: Move immediately to the next section, “SET UP FOR THE UPPER LIMIT”. If there is no action in 10 seconds, the motor will exit programming mode and you will have to restart. To restart, go to section “G” then to “B”

E) SET UP FOR THE UPPER LIMIT:

  1. Immediately after setting the lower limit, hold the up (A) button until blind starts moving freely upwards and stop close to your desired upper stop. Adjust with the help of up (A) and down (V) arrow.
  2. Click SET and let it jog. Hit SET again and let it jog.
    Note: To confirm that the upper and lower limits have been set properly, the blinds should move smoothly with one touch of the up (A) and down (V) buttons.

The blind is now fully programmed.

F) HOW TO PAIR MULTIPLE BLINDS TO THE SAME REMOTE CHANNEL:

  1. Using the next blind, follow the steps starting from “A” to “E”. Both blinds are now paired to the same channel.
    Note: Put the other blinds on sleep mode first. Hold the WHITE button on the motor for about 15 seconds until you hear a long beep.

G) HOW TO DELETE ALL MEMORY FROM THE MOTOR:

  1. Press the WHITE button the motor 4 times (beeping on each) and then hold on the 5t press until the motor jogs twice.

6-CHANNEL REMOTES:
When the remote shows 6 lights, all paired blinds are being controlled at the same time

16-CHANNEL REMOTES:
When the remote shows CC, all paired blinds are being controlled at the same time

CHARGING THE MOTOR:
Please charge the motor when it stops working
CHARGING THE MOTOR

SMART CONTROLLER

SETUP CODE CODE DE CONFIGURATION

Getting to know your Smart Controller
Getting to know your Smart Controller 

Smart Controller Status:
Flashing blue – Hotspot available
Flashing green – Connecting to the WiFi network
Pulsing cyan/blue-green – Connected to the Internet

Getting Started

  1. Download the Neo Smart Blinds app
    Download the app to your phone or tablet by searching Neo Smart Blinds on Google Play or the App Store.
    Note: Do not install Neo Smart Blinds Blue

  2. Plugin your Smart Controller in reach of your home WiFi
    Choose a place not too far from your home router or a place ‘you know has good WiFi signal strength. You will be able to change its location after, if necessary.

  3. Create an account and choose the setup code written on the cover
    After opening the app, tap on Create one to create anew account. Enter a valid email address and choose apassword, select the region time zone from the place where the Smart Controller will be located. Choose the setup code written in the cover and tap on Register.

  4. Follow the app step by step to add the Smart Controller
    Have in hand the home WiFi password. It will be necessary to connect the Smart Controller to the Internet.
    Note: Some Android users won’t be connected quickly to the hotspot. Ifit is the case, please wait about 10 seconds. before returning to the app. During this time, your device may notify you that the hotspot does not have Internet access, and will prompt you whether you want to remain connect- ed. You need to select the option that will allow you to keep connected before returning to the app.

System requirements

  • Astrong WiFi signal (3 bars or more) in the location where you will setup your Smart Controller.
  • The Smart Controller only supports 2.4GHz WiFi (IEEE 802 11b/g/n), not 5GHz. WiFi security needs to be set to WPA-PSK or ‘WPA2-PSK.
  • Asmartphone or tablet running Android 5.0 (Lollipop) or higher, or iOS 8 or higher is needed.

Mounting the Brackets

Measure 2″ — 3” in from the ends of the mounting profile and mark the bracket locations on the mounting surface. If more than two installation brackets are required for your shade, make additional marks to space the other bracket(s) evenly between the two end brackets. Adjust the bracket placement to gain clearance to avoid any obstructions, such as window cranks or handles. Center an installation bracket on each mark. Then, mark where to drill pilot holes for the mounting screws. With inside mounts, allow 2″ clearance behind the brackets for installation.

IMPORTANT NOTE: When installing bracket, DO NOT OVER TIGHTEN screw. Over tightening screw will deform the metal housing and interfere with the operation of the spring loaded clear plastic clip.

CEILING MOUNT

WALL MOUNT
Mounting the Brackets

TIP: The installation brackets must be mounted level to operate properly. If you are fastening the mounting brackets to drywall, be sure to use wall anchors and follow the instructions provided with the anchors.

Install the shade

Standard Installation
The groove on the top of the mounting profile fits into the hooks on installation brackets.
Install the shade into the installation brackets.
Hold the shade so the bottom bar fabric side faces you.
Hook the back groove of the mounting profile into the hooks of the installation brackets.
Rotate the mounting profile toward the clear tabs of the installation brackets. o Push the set bar until tabs lock into place. You will hear a loud click when each bracket is v/ securely in place.
Install the shade

Operate the Shade
Install the shade

Lowering the shade
Pull down and release. The Shade stops where released. >

Raising the Shade
Pull the shade down about an inch and release. The shade rises and stops.

Shade Adjustment
Install the shade

Stop Height Adjustment
The shade is preset in the “up” position to have the bottom rail exposed only. If you wish to have the roller blind stop in the “up” position at a lower height, follow the next steps:

  1. Completely roll up the shade.
  2. Tum the dial at the right end of the shade clockwise
  3. The shade will begin to lower.
  4. Stop when it reaches the desired height. This will reset the “up” position.

INSIDE/WALL TO WALL CEILING MOUNT SECTION

  1. Install Roller Shade Brackets first as per attached instruction sheet for “Fitting the Brackets Mount to Inside
    DO NOT INSTALL ROLLER SHADE YET. Frame/Ceiling

  2. PVC Valance has been notched on both ends on the roof of valance so as not to interfere with installed brackets. See Fig. 1.

  3. Install clear corners on ends of valance only if required before you install Valance.

  4. PutValance in place and screw through the roof of the valance to the inside of frame/ceiling. Use appropriate amount of screws to hold valance in place. Pre-drilling holes on roof of valance will help. You must ensure that the inside front of valance does not interfere with brackets and or roller mechanism. Leave a distance of approximately /2″ to 1” from end of roller bracket.

  5. Your are now ready to install Roller Shade. See section for “Fitting the Blind” on attached installation sheet.

  6. Ensure Child Safety Chain/Cord Hold Down Device is installed as per instruction sheet.
    PLEASE NOTE: Screws provided are for Installing into wood only.

OUTSIDE/WALL MOUNT

OUTSIDE/WALL MOUNT

  1. Install Roller Shade Brackets as per attached instruction sheet for “Fitting the Brackets”.
    DO NOT INSTALL ROLLER SHADE YET.

  2. Install Valance brackets as per Fig.

  3. Brackets should be installed approximately 4” from each end and spaced out evenly according to size of valance. Ensure valance brackets are mounted above installed roller brackets so as not to interfere when installing shade. Valance brackets should be installed approximately %2” to 1” above roller brackets. See Fig. 2.

  4. Assemble Valance before installing on installed shade. See Valance n assembly on reverse side.

  5. Center the valance over the installed roller Shade. Place the roof of completely assembled valance into the metal notched part on the top of valance bracket. Push roof of valance into the pressure fit notch of bracket. Roof of valance should be secured properly into the pressure fit notch lip. Valance returns should be resting and against wall. See Fig. 3.
    OUTSIDE/WALL MOUNT

VALANCE ASSEMBLY

The valance is to be mounted after the total installation.

  1. Attach the corner pieces into the back slot of the main valance section. Insert the side returns of the valance into the corner pieces. See Fig. A
    VALANCE ASSEMBLY

  2. Slide the excess fabric from the end of main valance into the side return grooves. See Fig. B
    VALANCE ASSEMBLY

  3. Insert the plastic top and bottom and push to secure the entire valance.  See Fig. C
    VALANCE ASSEMBLY
    PLEASE NOTE:
    Screws provided are for Installing into wood only.

INSTALLATION INSTRUCTIONS

Mount the brackets to the wall or window frame, with the outside brackets no further than 2inchas (5 cm) from the ends of the headrail. On wide shades, space the additional bracket(s) at equal intervals.
INSTALLATION INSTRUCTIONS

DELUXE2%”, 3’ & 4″ 

For wall or outside mounts, use the rear bracket holes.
Make sure the release tab is always mounted on the bottom.

For inside or ceiling mounts, use the top bracket holes.
Make sure the release tab is always mounted on the bottom.

Mount the headrail. Posttion the headrail with the front panel (A) resting on the top lip of all brackets. Push the bottom front of the headrail firmly backwards and toward the window until the lip on the rear of the headrail engages the bracket and snaps into place, (B) as shown.
Screws provided are for installing into wood only.
Mount the headrail

To remove a shade; Cassette 80: from the bottom rear of the headrail insert a flathead screwdriver in between the headrail and release tab. Gently twist the screwdriver and pry open the bracket to release the headrail. Raceway: Insert the screwdriver behind the headrail and engage the release tab.. press it upward to release the headrail. Cassette 120: from the top front of the headrail insert a flathead scraewdriver in between the headrail and release tab. Gently twist the scrawdriver and pry open the bracket to release the headrail. As you release the brackets, support the headrail to keep it from falling.

Install Brackets First

  1. The Brackets are mounted to the window with at least 2 screws per bracket. The open end pf the bracket should be facing downward. Ensure the location of clutch/idle end when installing. See Schematic of all components in Figure 1.
    ILLUSTRATION SHOWS RIGHT CONTROL.

  2. Brackets should be level.
    Front of Shade
    Installation

Install Shade

  1. Do Not Unroll Shade.
  2. Hold the shade with the fabric hanging from the back of the blind. /
  3. Install end plug first and then the clutch end. The Locating Hook de Must be pointing downwards as per drawing. See Figure 2.
    Installation

Chain Guide

  1. Place chain guide in place.
  2. Chain should be placed on either end of the chain guide. Place chain guide cover in place and install the 2 screws supplied. Lug should be facing downward. See Figure 3.
  3. The only time one of the chains are placed in the middle are for side channels only.
  4. Chain Dividers are not required for Motorized Shades.
    Installation

Install The Fascia

  1. Make sure the lug of the chain guide cover locks into the interior bead edge of fascia. )
  2. Place fascia on a slight angle to the top of bracket. The lip of fascia will rest on top of the slots of Fig. 3 brackets.
  3. Press front of fascia until you hear the fascia snap into the left and right of fascia brackets. See Figure 4.
    Installation

Square End Caps

  1. These are to be used when shade is installed on the outside of frame. This will cover the brackets for a more finished look.
  2. The caps have four pegs which are snapped into the 4 holes in the bracket. Screw
  3. Install the caps with the arrow pointing upward. You will find arrow on the inside of plastic end cap. See figure 5.
    Installation

Child Safety
Shadex is in compliance with the Consumer Product Safety Commission l Step1 Step 2 guidelines that have been enacted to reduce the risk of strangulation from ) — window covering cords. Although it is important to be in compliance, no ~ window covering product is completely child safe. It is imperative that \ End Cap window covering retailers discuss this hazard with all purchasers and make every effort to keep children away from cords. Every blind with cord controls is sent with a CSA compliant approved child safety hold down attached. If the customer removes this, they do so at their own risk.

Main Features

  • Cordless, novelty and safety design for your window
  • Quiet design with patent
  • Able to charge the motor via the switch wand, easy and convenient
  • Low-power dissipationdesign, rechargeable battery built in
  • The wand length can be eustomized

Operation

  1. Enter setting mode
    PS: No action in 10s, motor will quit setting mode automatically.
    Operation

  2. Switch Direction
    PS: Switch direction depend on working direction
    Operation

  3. Set first limit position
    PS: No action in 30s, motor will quit setting mode automatically.
    Operation

  4. Set other limit positions
    PS: No action in 30s, motor will quit limit set mode automatically
    Operation

  5. Limit fine tuning
    PS: No action in 30s, motor will quit setting mode automatically.
    Operation

  6. Delete certain Limit
    PS:Cannot delete direction depend on working direction
    Operation

  7. Dot move/continous move swith
    PS: Motor default Dot move, motor will keep  Dot move mode when Up and Down limits not been set, orin limit fine-tuning mode
    Operation

  8. Delete all limits
    PS:Factoryreset the motor resume to factory setting
    Operation

Troubleshooting

The home WiFidoesn’t appear in the step4
Try rescanning, if the problem persists, you will need to reposition the Smart Controller to a place with stronger WiFisignal. In this case, exit the process (tap on the menu, then tap Your Rooms), replace the Smart Controller and start over.

The Smart Controller LED in the bottom is not blinking blue The process fails in the last step
Press the S button for 10 seconds, then press the R button once and start over. Pay special attention when typing the WiFi password.

Need more help?

Visit neosmartblinds.com/smartcontroller for detailed instructions about how to use the app and troubleshooting.

Integrations

Smart home devices
Visit neosmartblinds.com/smartcontroller-integrations for detailed information about connecting to Amazon Alexa, Google Home and other systems.

Control4
Please send an email to tech@neosmartblinds.com with your name, your email and your company’s name. This information is necessary to always send to you any further driver update.

Legal Information FcC

‘Thisequipment has been tested and found tocomplywith the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. ‘These limits are designed to provide reason- able protection against harmful interference in aresidentialinstallation. Thisequipment generates usesand can radiate radio frequency energy and, ifnot installed and used i accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer- ence will not occur in a particular installa- tion. I this equipment does cause harmul interference to radioor television reception, ‘which can be determined by turning the equipment offand on, theuser is encouraged totryto correct theinterference by oneof the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help

Contains transmitter module FCC D COFWMNEM11
Tocomply with FCC/IC RF exposure limits for general population/ uncortrolled exposure, the antennals) used for this transmitter must beinstalled to provide a separationdistance ofatleast 20 cm fromall persons and must not be co- located or operating in corjunction with anyother antenna or transmitter.

ic
This device complieswith Industry Canada’s licence-exempt RSSs. Operationissubject to the following two conditions:

  1. This device may not cause interference; and
  2. This device must accept any interference, including interference that may cause unde- sired operation of the device.

‘This device meets the exemption from the routine evaluationlimitsin section 2.5 of RS5102 and users can obtain Canadian infor- mation on RF exposure and compliance.

Contains transmitter module IC: 10293A-WMNB11
This End equipment should be installed and ‘operated with aminimum distance of 20 centimeters between the radiator and your body.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SelectBlinds User Manuals

Related Manuals