ClearOne 910-2100-018 UNITE 260 PTZ Camera User Guide
- May 15, 2024
- ClearOne
Table of Contents
Quick-Start Guide
UNITE®
260 Pro Camera
QSG-0158-001v1.0 January 2023
ClearOne® Contacts
Headquarters
5225 Wiley Post Way Suite 600
Salt Lake City, UT 84116
Sales
Tel: +1.801.975.7200
sales@clearone.com
Headquarters
Tel: +1.801.975-7200
Technical Support
Tel: +1.801.974.3760
videotechsupport@clearone.com
Notices
© 2023 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice.
Document: QSG-0158-001v1.0 January 2023
Important Safety Information
- Before you set up the camera, read this manual carefully. Follow the setup instructions indicated in this manual.
- Keep this manual for future use.
- To prevent electric shock, do not remove screws or the camera housing. No self-serviceable parts are inside the housing
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
| CAUTION| **
---|---|---
THE LIGHTING FLASH AND ARROWHEAD WITHIN THE TRIANGE IS A WARNING SIGN
ALERTING YOU OF DANGEROUS VOLTAGE
INSIDE THE PRODUCT.| RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:** TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.| THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A
WARNING SIGN ALERTING YOU OF IMPORTANT
INSTRUCTIONS ACCOMPANYING THE PRODUCT.
SEE MARKING ON BOTTOM/BACK OF PRODUCT
| Use only in non-tropical locations.
---|---
| Use only at altitudes of 2000 meters or less.
Packing List
Verify that you have received all parts associated with each of the
components.
Inspect your shipment carefully. If the shipment shows obvious signs of
damage, retain original boxes and packing material for inspection by the
carrier, and contact them immediately. ClearOne is not responsible for product
damage incurred during shipment.
No| Product Description| Product Model
---|---|---
1| Unite 260 Pro Camera|
2| Remote| 
3| USB Cable|
4| AC Adaptor & Power Cord|
5| RS232 Cable|
Setup
Installation
This product should be placed on Wall mount or Celling Mount. Avoid contact
with any liquid, gas or solid material that may cause corrosion.
Step 1
Refer to the diagram below to make sure the connections are correct.
Step 2
Connect to the power, can be by PoE (48V DC), or 12V DC power supply.
Step 3
On the back panel of the UNITE 260 Pro, set the Power Switch to On. The LED
light on the front panel indicates the camera is powered on.
Step 4
The process of initialization is complete after the camera pan-tilt rotates to
the maximum position of top right and returns to the center.
Note: When the camera is connected, it will appear as a microphone
device. The camera only provides audio if you plug 3.5 mm analog line in
connector.
Note: If the position preset 0 has been stored, the position preset 0 will
be called up after initialization.
Remote Control
| No. | Name | Function Description |
|---|---|---|
| 1 | Standby Key | On/Off |
| 2 | Number Key | Preset setting or transfer preset |
| 3 | *Key | For use with other keys |
| 4 | Preset Key | Preset: Setting Preset ÷ Number key(0-9) |
| 5 | HOME key | Confirm selection or press to turn PTZ back to the middle |
position
6| Return Key| Return back to the last menu level
7| Zoom Keys| Moving between wide/narrow angle lens modes, slowly or quickly
8| L/R SET Key| Standard: Simultaneously press L/R SET key + 1
Reverse: Simultaneously press L/R SET key + 2
9| Focus Keys| Auto/Manual/Far-end/Near-end focus
10| CAMERA SELECT Keys| Select the camera to control
11| #Key| For use with other keys
12| IR Remote Control Key| [+#+F1/F2/F3/F4]: NO.1/2/3/4 address
13| Reset Key| Delete preset: [RESET] + Number key (0 – 9)
14| PTZ control keys| After zoom, press to move the PTZ
15| Menu Key| Used to enter/exit OSD Menu
16| BACKLIGHT Key| Turn on/off backlight
17| P/T RSTkey| For use with PTZ cameras
| Shortcut Set| Tracking mode/Short press to stop Auto Framing or Auto
Tracking
[] + [#] + [1]: OSD menu default English
[] + [#] + [3]: OSD menu default Chinese
[] + [#] + [4]: Display current IP address
[] + [#] + [6]: Quickly recover the default
[] + [#] + [8]: Display the camera version
[] + [#] + [9]: Quickly set up inversion
[] ÷ [#] + [MANUAL]: Restore to default IP address.
Functionality for F1 and F4
Short press F1 to start Auto Framing, and short press F4 to pause or start,
and long press F4 to close Auto Framing.
| No. | Function | Button |
|---|---|---|
| 1 | Auto framing | ON (F1) |
OFF (F4)
2| Auto tracking| On (F3)
OFF (F4)
Safety Precautions
Installation
This product should be placed on a smooth flat surface, or bracket-mounted, if
desired. Avoid contact with any liquid, gas or solid material that may cause
corrosion.
Do Not Disassemble
This product has no user-repairable parts. Damage caused by unauthorized
disassembly is not covered by warranty.
Notice
Electromagnetic fields at specific frequencies may affect image quality.
Troubleshooting
Image
Image is jittery when the camera is properly connected:
- Ensure that the camera is installed in a stable position.
- Remove vibrating objects/machinery from the proximity of the camera.
Control
Remote control not operating
- Check/replace batteries in the remote control unit.
- Ensure the camera working mode is correct.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>