Thermaltake LTP-0650P-2 Litepower RGB 650W Power Supply Instruction Manual
- June 4, 2024
- thermaltake
Table of Contents
Thermaltake LTP-0650P-2 Litepower RGB 650W Power Supply
Warnings and cautions
- Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
- Do not place the power supply in a high humidity and/or temperature environment.
- High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
- PSU should be powered by the source indicated on the rating label.
- All warrantees and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this manual.
Components Check
- LITEPOVWER power supply unit
- User manual
- AC power cord
- Mounting screw x 4
Power Connector Introduction
Cable
P/N
| | | | | |
---|---|---|---|---|---|---
Main Power Connector
(24Pin)
| ATX 12V
Connector
(4+4Pin)
| PCI-E
Connector
(6+2Pin)
| SATA
Connector
(5 Pin)
| Peripheral Connector
(4Pin)
| Floppy Connector
(4Pin)
LTP-0650P-2 LTP-0650P-F| 1| 1| 2| 5| 6| 1
LTP-0550P-2 LTP-0550C-F| 1| 1| 2| 5| 4| 1
LTP-0450P-2 LTP-0450C-F| 1| 1| 2| 4| 4| 1
LTP-0350P-2 LTP-0350C-F| 1| 1| 0| 3| 3| 1
Installation Steps
Note: Make sure that your system is turned off and unplugged.
Disconnect the AC power cord from your old power supply.
-
Open your computer case; please refer to the direction in your case manual.
-
Install the PSU into the case with the four screws provided.
-
If your motherboard requires a 24pin Main Power connector, please connect the 20+4pin Main Power connector to the motherboard.
If your motherboard only requires a 20pin Main Power connector, please detach the 4pin connector from the 20+4pin Main Power connector hen connect only the 20pin connector to the motherboard. -
For motherboard that only requires a 4pin ATX 12V (CPU) connector, please detach a 4pin connector from the 4+4pin ATX 12V connector and connect it to the motherboard.
(Either one of the 4pin from the 4+4pin ATX 12V connector will work) -
Connect other peripheral power connectors to devices such as hard drives, optical drives, etc.
-
Connect any devices that may use the 4 pin peripheral connectors. ie; hard drives, CD / DVD drives or case fans.
-
If your graphic card requires PCI-E power connector, please connect corresponding PCI-E connector instructed by your graphic card’s user manual. Please note the power supply utilizes a unique 6+2pin PCI-E connector that can be effectively used as a single 8pin or 6pin PCI-E connector. To use it as a 6pin PCI-E connector, please detach the 2pin connector from the 6+2pin connector.
DO NOT PLUG THE PCI-E CABLE INTO THE CPU POWER CONNECTION.
THIS WILL DAMAGE YOUR SYSTEM. -
Close your computer case and connect the AC power cord to the power supply AC inlet.
Output Specification
Total protection
EMI & SAFETY
Environments
Trouble-Shotting
If the power supply fails to function properly, please follow the troubleshooting guide before application for service:
- Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
- Please make sure the I/O switch on the power supply is switched to I position.
- Please make sure all power connectors are properly connected to all the devices.
- If connected to a UPS unit, is the UPS on and plugged in?
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>