ClearOne Aura Unite 200 PTZ HD Camera User Guide

June 4, 2024
ClearOne

Unite 200 PTZ HD Camera
User Guide

ClearOne Aura Unite 200 PTZ HD Camera -

Important Safety Information

Before you set up the camera, read this manual carefully. Follow the setup instructions indicated in this manual. Keep this manual for future use. To prevent electric shock, do not remove screws or the camera housing. No self- serviceable parts are inside the housing.
Installation
Place product on a smooth flat surface, or bracket mount. Avoid contact with any liquid, gas or solid material that may cause corrosion.
Do Not Disassemble
This product has no user-repairable parts. Damage caused by unauthorized disassembly is not covered by warranty. Electromagnetic fields at specific frequencies may affect image quality.
WARNING: TO PREVENT FIRE OR  ELECTRICAL SHOCK HAZARDS, DO NOT EXPOSE YOUR PRODUCT TO RAIN OR MOISTURE.
THE LIGHTING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS  A WARNING SIGN ALERTING YOU OF  DANGEROUS VOLTAGE INSIDE THE PRODUCT.
CAUTION
THE RISK OF ELECTRIC SHOCK DOES NOT OPEN
AVIS RISQUE DU CHOC ELECTRIQUE – NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR  ACK)  NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
** THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING IT. SEE MARKING ON BOTTOM/BACK OF PRODUCT
THE PRODUCT.
**ClearOne Aura Unite 200 PTZ HD Camera - Fig Use only in non-tropical locations.
Use only at altitudes of 2000 meters or less.

Packing List

Verify that you have received all parts associated with each of the components. Inspect your shipment carefully. If the shipment shows obvious signs of damage, retain original boxes and packing material for inspection by the carrier, and contact them immediately. ClearOne is not responsible for product damage incurred during shipment.

| • UNITE 200 Camera
• Remote Control
---|---
| • AC Power Adapter with Power Cord
• PoE Splitter
| • RS-232 cable
• USB 3.0 cable, Type A and Type B connectors

Introduction to the UNITE 200 PTZ HD Camera
Front View

ClearOne Aura Unite 200 PTZ HD Camera - Fig 5

Back View

ClearOne Aura Unite 200 PTZ HD Camera - Fig 6

a. System Select Switch
b. RS-232 Out Port
c. RS-232 In Port
d. RJ45 Port
e. Reserved Port
f. Line In Port| g. Reserved Port
h. HDMI Port
i. USB 3.0 Port
j. Reserved Port
k. DC In 12 V Port
l. Power Switch
---|---

Bottom View

ClearOne Aura Unite 200 PTZ HD Camera - Fig 7

m. Bottom Switches
n. Tripod Screw Hole
o. Fixing Screw Hole

Connect
Make connections as shown in the following diagram:

ClearOne Aura Unite 200 PTZ HD Camera - Fig 8

Caution: Do not apply power until after you set the switches.
Power options

  • Use the PoE splitter to connect to power and ethernet, or
  • Use the AC adapter, and an ethernet cable to connect the RJ-45 port to an external device.

Set Switches

DIP Switches
On the bottom of the unit, set both switch 1 and switch 2 to Off.

| SW – 1| Mode
---|---|---
1| Off| Normal Working Mode
2| On| –
3| Off| –
4| On| –

Video System Switch
On the backplane of the unit, set the switch to the desired settings. Video format options:

VIDEO SYSTEM

0| 1080p60| 8| 720p30
1| 1080p50| 9| 720p25
2| 1080I60| A| –
3| 1080I50| B| –
4| 720p60| C| –
5| 720p50| D| –
6| 1080p30| E| –
7| 1080p25| F| –

Note: After you change the switch, for the change to take effect,  you must restart the camera.
Start-Up

  1. If you are not using the PoE Splitter, connect the AC power adapter to a power source.
  2. On the back panel of the UNITE 200, set the Power Switch to On. When the camera starts, Pan-Tilt rotates to the maximum position of top right, then returns to the center position. This completes the initialization process.

Note: If the position preset 0 has been stored, then after initialization, the position preset 0 is called up.
If you want to restore the factory default settings:
a. Press the Menu button to display the On-screen Display (OSD) menu.
b. Select Menu >Restore Default > Restore.
c. Set the value Yes, then press the HOME button.

IR Remote Control

Note: Power consumption in standby mode is approximately half of the normal mode

ClearOne Aura Unite 200 PTZ HD Camera - Fig 12

More detailed information about using the UNITE 200 PTZ HD Camera is provided in the UNITE 200 User Manual, available in the ClearOne Resource Libary.
CONTACT INFORMATION

Headquarters
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
US: +1.801.975.7200
International: +1.801.975.7200| Aura Sales
US: +1.888.HEY.AURA
International: +1.801.975.7200
aurasales@clearone.com
Aura Tech Support
US: +1.888.HEY.AURA
International: +1.801.975.7200
auratechsupport@clearone.co
---|---

Notices
© 2021 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice.
Document: QSG-0128-002v1.2, September 2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals