CADAC 202P1 2-cook Pro Deluxe kooktoestel Instruction Manual

: June 5, 2024
: CADAC

Table of Contents

General
Safety information
Assembly Instructions
Fitting and Changing the Gas Cylinder
Operating the Appliance
General Maintenance
Troubleshooting
Cleaning
Storage
Spares
Returning the Appliance for Repair or Service
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

2 COOK2 PRO
MODEL No: 202P1, 202P0
28mBar & 50mBar

202P1	202P0

PERMIT 1002-145/2-RSA-17-A
USER INSTRUCTIONS

NOTE! PRODUCT MAY VARY FROM ILLUSTRATIONS
503-0543 LEV20

CAUTION
Provide ample ventilation. This gas appliance consumes air (oxygen). Do not use this appliance in an unventilated space to avoid endangering your life. If still more gas appliances and/or occupants using gas are added to the space, additional ventilation must be provided.

IMPORTANT
Read these instructions carefully so as to familiarise yourself with the appliance before fiting the appliance to a gas cylinder.
Retain these instructions for future reference.

General

This is an economic gas appliance designed for an optimal cooking experience using environment friendly LP gas.
The appliance conforms to BS EN 484: 2019 and SANS 1539:2017.
Note that figures in this user manual are shown for visual purposes only and may differ to your appliance.
Please read all the instructions and warnings on the appliance before use.
It is important that all gas connections have been correctly connected to prevent any gas leaks.
Do not use a leaking, damaged or malfunctioning appliance.
This appliance must only be used with an approved hose and regulator. (A 2.8kPa hose and regulator supplied only in South Africa)
Ensure that the appliance is used in a well-ventilated area.
Handle the appliance with care, do not drop it.
When using a pot, the minimum recommended pot size is 180mm and maximum pot size is 250mm.
The gas cylinder is to be used in an upright position only.
Read the instructions before using the appliance. · Use Outdoors Only

Safety information

These instructions are for your safety and to help you avoid risk of injury and/or damage. All warranties will become void if you do not follow these instructions.

Fig-1	Fig-2

The hose and seal on the regulator must be checked for wear or damage before every use and before connecting to the gas cylinder.
In the event of light back (where the flame burns back and ignites at the jet) immediately turn off the gas supply by first closing the control valve on the gas cylinder and then the appliance valve. After the flame is extinguished remove the regulator and check the condition of its seal, replace the seal if in doubt. Re-light the appliance. Should the flame persistently light back again return the product to your authorised CADAC repair agent.
Ensure the appliance is used away from flammable materials. Minimum safe distances; above the appliance 1.2 m, at the rear and sides 0.6m (Fig. 2).
Do not use an appliance that is leaking, damaged or which does not operate properly.
Ensure that the gas cylinder is fitted or changed in a well-ventilated location, preferably outdoors, away from any sources of ignition, such as naked flames and away from other people.
Keep gas cylinders away from heat and flame. Do not place on a stove or any other hot surface.
Ensure that the assembled product is stable and does not rock.
Never leave the appliance unattended when lit.
If there is a leak on your appliance (smell of gas), turn off the gas supply, firstly at the gas cylinder and then on your appliance by turning the respective knobs fully clockwise. Take them outside immediately into a well-ventilated flame-free location where the leak may be detected and stopped.
This appliance consumes oxygen and needs ventilation for optimum performance and for safety of those in close proximity.
Room ventilation is important for the efficient performance of the appliance and for the safety of the occupants in the room.
The room where this appliance is used should have a window or a door that can be opened or partially open during use. If there is no window or door available for room ventilation, extra ventilation must be installed for your safety.
If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame, use soapy water. The correct way is to smear the joints with soapy water. If bubbles form then there is a gas leak. Immediately turn off the gas supply first by closing the control valve on the gas cylinder and then the appliance valve, check that all the connections are properly fitted. Re-check with soapy water. If a gas leak persists return the product to your CADAC dealer for inspection/repair.
Do not modify the appliance. Do not use it for anything for which it has not been designed.
During use, parts of the appliance will become hot (particularly the burner) Avoid touching hot parts with bare hands. The use of gloves is recommended.
Keep young children away from the appliance at all times.
Do not twist or pinch the hose.
Do not move the appliance during use.
Do not use the appliance without the Potstands being in place and properly located.
Turn off the gas supply at the gas container after use.
Do not modify the appliance, any modification may be dangerous.

Country of Use| BE, CH, CY, CZ, ES, FR, GB, GR,
1E, IT, LT, LU, LV, PT, SK & SI| PL| BE, CY, DK, EE,
FR, FI, HU, IT, LT,
NL, NO, SE, SI,
SK, RO, HR, TR,
BG, IS,LU, MT,
& ZA| AT, CH, DE & SK
---|---|---|---|---
Appliance Catagories| 13+(28-30/37)| 138/P (37)| IMP (30)| 138/P (50)
Allowable gasses| Butane-G30| Propane-G31| Butane-G30, Propane-G31 or their mixture
Gas Pressure| 28-30mBar| 37mBar| 37mBar| 28-30mBar
(2.8kPa for South
Africa)| 50mBar
Jet Number| 0.71| 0.71| 0.71| 0.62
Nominal Usage| Butane – 145.5 g/h
per burner
(145.5g/h x 2 = 291g/h in total)| Butane – 160 g/h
per burner
(160g/h x 2 = 320g/h
in total)| Butane – 145.5g/h
per burner
(145.5g/h x 2 =
291g/h in total)| Butane – 145.5g/h
per burner
(145.5g/h x 2 =
291g/h in total)
Gross nom. heat input| 2kW per burner
(2kW x 2 = 4kW in total)| 2.2kW per burner
(2.2kW x 2 = 4.4kW
in total)| 2kW per burner
(2kW x 2 = 4kW
in total)| 2kW per burner
(2kW x 2 = 4kW
in total)
Country Name and Abbreviations

Assembly Instructions

PLEASE NOTE: Please ensure all protective packaging and plastic are removed from the appliance before use. This appliance may only be used with an approved hose and regulator (hose and regulator supplied with this unit in South Africa) Connect the regulator to a CADAC 3kg, 5kg or 7kg LPG cylinder prior to use. If you wish to use the appliance with a 9kg cylinder, please ensure that you have purchased the correct hose and regulator suitable for a 9kg cylinder.
The hose length should be no less than 0.8m and shall not exceed 1.2 m and replace when the hose is damaged or shows signs of brittleness or cracks.
Do not twist or pinch the hose. Ensure that it is routed away from the Stove Body so as to prevent deterioration/damage to the hose caused by heat.
Ensure that the appliance valves are in the off position by turning the knobs fully clockwise to the stop. Open the gas valve on the cylinder and test for any leaks. Check all gas connections for any signs of gas leaks. Your appliance is now ready to be used.

I 3B/P (30), I 3+ (28-30/37) and I 3B/P (37), Appliance categories: (DK, FI, NO, NL, SE, AT, DE, BE, ES, FR, IE, IT, PT, GB, CH)
Push an approved hose onto the valve tailpiece until it is properly seated. On the other end, attach a suitable low pressure regulator.
I3B/P(30) : 30mbar Butane configurations regulator or 30mbar Propane configurations regulator.
I3B/P(37) : 37mbar Butane configurations regulator or 37mbar Propane configurations regulator.
I3+(28-30/37) : 30mbar Butane configurations regulator or 37mbar Propane configurations regulator. Again making sure that the hose is properly seated. The type of hose used shall comply with the relevant EN standard and locate requirement. In South Africa the regulator used must comply with SANS 1237.

I 3B/P (50) Appliance category: (AT, DE)
I3B/P(50): 50mbar Butane configurations regulator or 50mbar Propane configurations regulator or 50mbar butane/propane mixture configurations regulator. Screw a hose with the correct threaded fittings on each end, onto the left hand 1/4″ BSP thread of the valve. Attache a suitable 50mbar low- pressure regulator on the end of the hose. The hose assembly used must comply with DIN 4815 part 2 or equivalent.

Product Code: 202P1-20

Product Code: 202P0-10

Fitting and Changing the Gas Cylinder

Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the Regulator is in position and in good condition.
Carry out this check each time you fit the appliance to a gas cylinder.
Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
Ensure that the appliance valves are in the off position by turning the knobs fully clockwise to their stop.
Ensure that the gas cylinder is fitted or changed in a well-ventilated location, preferably outdoors, away from any source of ignition, such as naked flames and away from other people.
Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by screwing on hand tight until fully engaged.
Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). If there is a leak on your appliance (smell of gas), take it outside immediately into a well-ventilated flame free location where the leak may be detected and stopped. To check for leaks on your appliance, do it outside using warm soapy water only, which is applied to the joints and connections of the appliance. A formation of bubbles will indicate the gas leak. Do not check for leaks with a naked flame.
If you cannot rectify the gas leak do not use the appliance, contact your local CADAC stockist for assistance.
CADAC gas cylinder valves must only be repaired by an authorised CADAC service centre or dealer.
When changing a gas cylinder firstly close the appliance control knobs and then the cylinder valve, making sure the flame is extinguished, unscrew the regulator. Re-fit the regulator to a full cylinder following the same precautions as described above.

Operating the Appliance

The appliance is designed for use with cooking vessels of not less than 180mm in diameter and not greater than 250mm in diameter. After lighting, do not move the gas cylinder and the appliance around, as liquefied gas may enter the appliance from the gas cylinder, causing it to flare (large yellow flames). Always operate the appliance on a firm level surface with the gas cylinder in an upright position.

Lighting the Appliance using the piezo:

Turn the control knob clockwise to the `OFF’ position.
Turn the gas supply `ON’ at the cylinder.
Push down the control knob and keep pressing whilst turning anti-clockwise to the `Ignition’ position. This should light the burner. Repeat this several times until the burner lights. If not, wait at least 3 minutes and repeat this process.
When the burner is lit, keep the control knob pressed for a few seconds, then release it.
If the burner does not stay alight, repeat steps 3 and 4. Adjust the heat by turning the knob to the `High/Low’ position.
To turn the stove OFF’, turn the cylinder valve to theOFF’ position and then turn the control knob on the appliance clockwise to the `OFF’ position.
Always close the cylinder valve after usuage. This will prolong the life of the regulator and prevent any gas leakages if the appliance is not in use.

Warning: If the burner fails to ignite within 10 seconds, turn the control knob off (clockwise). Wait three minutes before attempting to re-light with ignition sequence.

Lighting the Appliance with a match:

To light the appliance, light a match or barbecue lighter, turn on the appliance valve after connecting to and opening the cylinder valve, by turning the control knob in an anti-clockwise direction. Light the appliance burners.
Use the control knob to adjust the flame intensity to the desired level by turning the knob clockwise to decrease the flame and anti clockwise to increase it.
Always light the match or the lighter first before opening the gas valve on the appliance.

General Maintenance

This appliance does not require scheduled maintenance.

It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if they are not in order, before using the appliance.
If the appliance was in use, it will be hot. Allow to cool sufficiently before attempting any maintenance.
The Stoves are fitted with jets to regulate the correct amount of gas.
Should the hole in the Jet become blocked this may result in a small flame or no flame at all.
Do not attempt to clean the jet with a pin or other such device as this may damage the orifice, which could make the appliance unsafe.

Replacing a blocked jet:

Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.
Remove the Potstand/cooking surfaces from the stove body.
Turning the appliance upside down, unscrew the screws holding the bracket of the burner to the body.
From the top now, you can safely remove the burners from the appliance.
Unscrew the blocked jet from the valve with a suitable spanner and replace it with a new jet.
Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.
Do not use pliers on the jet as this may damage the jet making it unusable or impossible to remove.

Troubleshooting

A normal flame is blue and may have a yellow tip. If the flame is completely yellow, it may be that the jet is not securely fitted. Retighten the jet to give a gas tight seal. An overfilled gas cylinder can also cause large yellow flames. Cylinder should be returned to filling station and checked by weight.
Check that the inlet to the burner pipe is clear and free of obstructions.
If the flame power drops or the gas will not light, check that the gas cylinder still contains gas (shake to hear the noise made by the liquefied gas). If there is still gas, the jet might have become blocked or partially blocked.
NOTE! Shake the gas cylinder only when the cylinder valve and device control knobs are in `OFF’ position!
If you suspect a blocked jet, follow the instructions above. · Check for spider webs or insect nests in the gas tube or primary air inlet.

Cleaning

It is recommended to clean your appliance after every use. This will prolong the life of your appliance.
The Potstand is removed by lifting it from the stove top and can be washed in a detergent solution.
To clean the stove body, simply wipe with a damp cloth using a little detergent, if necessary.
DO NOT IMMERSE IN WATER as this will allow water to get into the burner tube causing the appliance to malfunction.
Do not use abrasive cleaners or scourers as this will cause permanent damage to the surface.
To avoid ignition failure, keep the burners clean.
Use a brush to clean the burners.
A tooth brush may be used to clean out the venturi should there be any obstacles within the venturi.

Storage

Handle the appliance with care. Do not drop it.
After use, wait until the appliance has cooled down, disconnect it from the gas cylinder and store them in a cool dry place. Store your cylinder in a well-ventilated place.
It helps to place the appliance in a plastic bag when not in use as this will prevent the ingress of dirt and insects, which may affect the gas flow.
Warning: An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
LPG cylinders should preferrably be stored outdoors if not in use.

Spares

Always use genuine CADAC spares as they have been designed to give optimum performance.

Returning the Appliance for Repair or Service

Do not modify the appliance. Any modification of the appliance may be dangerous.
Any modifications will render the CADAC warranty null and void.
If you cannot rectify any fault by following these instructions, contact your local CADAC distributor for inspection/repair

Warranty

CADAC (Pty) Ltd hereby warrants to the ORIGINAL PURCHASER of this CADAC gas appliance for 2 years, that it will be free of defects in material and workmanship from the date of purchase as follows:

Valves: 2 Years
Plastic parts: No Warranty
Enamel parts: 2 Years
Cast Iron: 2 Years
Burners: 1 Year

The warranty will only apply if the unit is assembled and operated in accordance with the printed instructions.
CADAC may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use and service and which on examination shall indicate, to CADAC’s satisfaction, they are defective. Before returning any parts, contact the customer service representative in your region using the contact information provided with your manual. If CADAC confirms the defect and approves the claim, CADAC will elect to replace such parts without charge. CADAC will return parts to the purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this owner’s manual. Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not cover by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to you.

CADAC is not liable for any special, indirect or consequential damages. Some regions do not allow the exclusion or limitation of incidental or consequential damages, to this limitation or exclusion may not apply to you.

CADAC does not authorize any person or company to assume for it any obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on CADAC.

This Warranty applies only to products sold at retail.

To enjoy and ensure longevity of your CADAC product, please refer to the cleaning and maintenance section of the user manual with particular attention to the care of the Stainless Steel.

CADAC INTERNATIONAL
P.O. Box 43196, Industria, 2042 South Africa
Tel: +27 11 470 6600
Email: info@cadac.co.za
www.cadacinternational.com

CADAC UK
14 Deanfield Court, Link59 Business Park, Clitheroe, Lancashire,
BB7 1QS
United Kingdom.
Tel: +44 (0) 333 2000363
E:mail: info@cadacuk.com
www.cadacinternational.com

CADAC SWEDEN & NORWAY
KAMA FRITID AB
0046 36 353700
info@kamafritid.se