FONESTAR 7938XT HDMI Splitter User Guide
- May 15, 2024
- Fonestar
Table of Contents
FONESTAR 7938XT HDMI Splitter
Product Information
- Specifications:
- Model: 7938XT
- Function: HDMI Extension via Cat 6 Cable
- Transmission Distance: Up to 60m for 1080p@60Hz HDMI signals
- Cable Compatibility: Cat 6/6a/7 (FTP/SFTP)
- Power Input: 5V DC
Product Usage Instructions
- Connection Setup:
- Connect the monitor or projector to the receiver output using an HDMI cable.
- Connect the audio/video player (DVD, BluRay, computer, etc.) to the transmitter input via HDMI cable.
- Use HDMI cables of the shortest possible length to minimize signal loss.
- Cat 6 Cable Installation:
- Install Cat 6 or higher data cable and connect both ends to the transmitter and receiver Cat ports.
- IR Extender Setup (Optional):
- Use IR extenders to control the video signal source with your remote from the monitor position.
- Connect the TX extender jack to the IR OUT of the transmitter and the RX extender jack to the IR IN of the transmitter.
- Power Supply:
- Use the provided power adapter to power the receiver via the data cable.
- In long cable runs, power the receiver with a 5V DC, and 0.5A power adapter if needed.
- Turning on Devices:
- Turn on both devices connected to the transmitter and receiver.
- Additional Settings:
- Reset: Press the reset button to adjust the signal based on cable length.
- Resolution: Long press the 720p/1080p button to switch between image resolutions.
- Signal Indicator: Indicates video signal detection at the input.
- Link Indicator: Shows connection status between transmitter and receiver.
FAQs
- Q: What is the maximum transmission distance for 1080p@60Hz signals?
- A: The maximum distance is up to 60 meters using a Cat 6 cable.
- Q: Can I use Cat 6a or Cat 7 cables with this product?
- A: Yes, this product is compatible with Cat 6, Cat 6a, and Cat 7 cables with FTP/SFTP shielding.
DESCRIPTION
- Increases the transmission distance of 1080p@60Hz HDMI signals up to 60 m through Cat 6 cable.
- The use of Cat 6 cables simplifies the running of the cable through pipes and walls, reducing the difficulty and time required for installation.
- In addition, it carries the remote control signal from the TV receiver to the transceiver to control the receiver or player.
CONTROLS AND CONNECTIONS
TRANSMITTER (Tx)
RECEIVER (Rx)
OPERATION
- With the devices disconnected from the power supply, connect the monitor or projector to the output of the receiver using an HDMI cable. And connect the audio/video player (DVD, BluRay, computer, etc.) to the input of the transmitter via HDMI cable.
- NOTE: it is recommended that you use HDMI cables of the shortest possible length to reduce signal loss caused by the cable.
- Install the Cat 6 or higher data cable and connect both ends to the CAT ports. 6 transmitter and receiver.
- OPTIONAL
- Use IR extenders to control the device that generates the video signal with your remote from the monitor position.
- Insert the extender jack connector identified as TX into the IR OUT connector of the transmitter. Position this in front of the IR receiver on the device.
- Insert the extender jack connector identified as RX into the IR IN connector of the transmitter. And place the remote in a visible place so that you can point the remote control.
- Use the supplied power adapter. The receiver will be powered via a data cable. In long cable runs it may be necessary to power the receiver as well. To do this, use a power adapter of the same characteristics 5 V DC, 0.5 A.
- Turn on the devices connected to the transmitter and receiver.
- Additional settings:
- RESET: press this button to adjust the signal according to the length of the cable used.
- RESOLUTION: Long press the 720p/1080p button to change the image resolution between 720p and 1080p.
- SIGNAL INDICATOR: signal status indicator light. Lights up if the video signal is detected at the input.
- LINK INDICATOR: indicator light of the status of the connection between transmitter and receiver. Lights up to indicate successful connection. If it is not turned on, check that the data cable is correct, has no damage, the connectors do not come out of the ports, the pinout is adequate and its length does not exceed the recommended length (60 meters maximum for 1080p@60Hz signals). Finally, press the RESET button to restart the connection.
IMPORTANT – DATA CABLE
The pinout of both ends of the cable should follow IEEE-568B:
- High-quality Cat 6 cables with FTP/SFTP shielding are recommended. Cables should have shielded connectors with the cable shielding connected to the connector shield.
- This improves the reliability of the HDMI extenders, avoiding ground loops caused by interconnecting devices (player/receiver and TV) with different ground references which may cause loss or break-up of the image.
INSTALLATION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>