ideal lux 8I139470 Gas Bollard Light Instruction Manual
- May 15, 2024
- ideal lux
Table of Contents
8I139470 Gas Bollard Light
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
SAFETY INSTRUCTIONS
1. This fitting is produced and tested in accordance with the strictest
European safety standards
(EN 60.598-1).
2, This fiting cannot be disposed of as household waste. For disposal
information ask the local
authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be
installed by a qualified
electrician
4. Ifthe external wire is damaged it has to be replaced exclusively by the
manufacturer, distributor
or by a qualified electrician.
5, Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall
plugs suitable for
‘the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws fimly to avoid contact problems.
9. This fiting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fiting is only suitable for fixing to the citing.
13. This fiting is only suitable for fixing to the wall
14. The weight of the lamp has to be supported by the chain. Adjust the
length of the electric wire
0 that itis longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16, Always observe the minimum distance between the lamp and the surface being
lit, as shown in
the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen
bulls get very hot. Wait
until they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only
manufoturer approved
parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not
disassemble the product
since the diodes can damage the eyes. Do not immerse in water. Wipe with a
damp cloth. Do
not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class | Electrical safety guaranteed by the main insulation and an
additional protective conduotor
(earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety guaranteed by the main insulation and a double
or reinforced insulation,
Earthing not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (lees
than 60 Voit). Earthing
excluded.
24. Not protected
25. Protected against solid objects greater than 60 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,6 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totaly protected against dust infitration.
31. Not protected
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 16° to the
vertical axis.
34. Protected against rain
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.