MOBICLINIC Veleta Mini Elliptical Trainer Instruction Manual

Table of Contents

MOBICLINIC-Veleta-Mini-Elliptical-Trainer-product

Connect the charger to the unit and plug it into the socket. The display will turn on.
Press the “POWER” button, the display will show the default time of 20 minutes.
Press the “Speed+” or “Speed-” button to change the time to a minimum of 5 minutes or a maximum of 30 minutes.
Once you have selected the time, you can press the “POWER” button to start the elliptical. It will start with the manual program and the display will show speed 1.
You can adjust it from 1 to 10 with the “Speed+” and “Speed-” buttons. The maximum speed is 10.
You can press the “MODE” button to change the program to automatic P1, P2 or P3.

Keep the device away from the reach of children and pets.

To avoid injury or irreparable damage, always remain seated when using the appliance. Never stand on the unit.
Do not attempt to disassemble or repair the appliance.
This should only be done by qualified technicians.
For delicate floor surfaces (e.g. parquet), we recommend placing a mat or carpet under the unit to prevent damage or discolouration.
For indoor use only. This article is not a medical device and is not intended for the treatment or prevention of diseases

WARNINGS

Keep the instructions for future reference, if the device is handed over to a third party, these instructions must also be handed over.
Discontinue use immediately if you experience discomfort.
Do not use the product before going to sleep. It may have a stimulating effect and delay sleep.
To avoid a short circuit, connect the device correctly and keep it away from metal, rubbish and water.
Use the device on a flat surface. If it is not stable, it may tip over and cause injury.
Unplug the charger from the wall socket when not in use.
If you suspect a problem, disconnect the device immediately.
If the connection cable is damaged, it must be replaced.
This should only be done by an authorised and qualified person.
To avoid the risk of electric shock, do not operate the appliance with wet skin.
Keep the product away from moisture and sun exposure. Do not use it if there are damp parts.

$MOBICLINIC-Veleta-Mini-Elliptical-Trainer-fig- $2$$

Always disconnect the power plug before cleaning.
Clean the device and the silicone bases with a damp cloth and mild soap. Do not use abrasive or corrosive cleaning agents. The silicone pads can be removed for easy cleaning.
Never allow the appliance to come into contact with water or other liquids.
Store the unit in its original packaging if it is to be stored for a long period, or in a safe, cool and dry place.

The device is designed for use with the legs.
Connect the charger to the socket and the cable to the unit. As soon as it is plugged in, you will hear a beep and the control panel will light up.
Once plugged in, turn it so that the control panel is facing forward. Select a mode according to your needs using the remote control or the control panel.
Your settings will be displayed on the screen. To start, press the “Start/Stop” button. Sit down and place your feet on the pedals.
To switch off the appliance correctly, you must first press the “Start/Stop” button on the control panel or remote control. Then press the power button on the device to turn it off completely.
Unplug the appliance from the power socket when you have finished using it.

Power button: Press this button on your unit to turn it on and off.
Start/Stop: Press this button to start with your selected settings. When the device is running, press this button to stop it.
Speed+: Increases the speed. The speed can be manually adjusted from 1 to 10. Press the button to increase the speed while in operation.
Speed-: Decreases the speed. The speed can be manually adjusted from 1 to 10. Press the button to decrease the speed while in operation.
Function: Press this button to display SCAN, TIME, DISTANCE, SPEED, STEP and CALORIE.
Direction: Press this button to change the pedalling direction.
Mode: Press this button to select one of the programs: Automatic programs P1, P2 and P3 or manual programs.