VAIO VJ8MS1A Wireless Mouse User Guide
- May 15, 2024
- VAIO
Table of Contents
VAIO VJ8MS1A Wireless Mouse
Before Use
Notes
All parts have to be unpacked and the packaging material has to be removed
completely. Before use, verify the package contents are complete and
undamaged.
BATTERY WARNING STATEMENT
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
(System Requirements)
- Windows 7/8/10 or newer version, Mac OS 10.5 or newer version and Chrome OS
- Available USB port or Bluetooth®
What’s in the Box
- 1 Wireless Mouse
- 1 USB nano receiver
- 1 AA battery
(Specification)
- 3 clickable buttons with 1600 DPI sensitivity
- Connect to up to 3 devices simultaneously with Bluetooth® wireless technology or a USB nano receiver (stored in the battery compartment when not in use)
- USB plug-and-play
- Scroll wheel
- On/off switch
- Easy switch for switching connection: 2.4Ghz/Bluetooth® 1/Bluetooth® 2
- Windows, MacOS, ChromeOS, Android, iOS compatible
Functional Introduction
- Left button
- Right button
- Scroll wheel
- LED indicator
- USB nano receiver
- Connect button
- Battery cover
- Easy switch
- ON / OFF switch
Switch Connection Channel
- This mouse can be connected to up to 3 different computers.
- Use the “Easy switch” to change connection channels between the USB nano receiver and 2 other Bluetooth channels.
Switch Devices
****You can set a USB nano receiver ( ) on computer A
- Bluetooth 1 ( ) on computer B
- Bluetooth 2 ( ) on computer C and use the “Easy switch” to switch the connection between these 3 computers.
Connect button
Press and hold this button to set the mouse in Bluetooth pairing mode, and
also for reconnecting to a paired device.
Installing Batteries
Insert the battery in the correct position according to the instruction label
on the mouse.
Connection Setup
Connect via USB nano receiver
It is plug-and-play for a USB nano receiver, make sure to turn on the power
and set the connection channel on the USB nano receiver ( ) then just plug in
USB receiver into the available USB A port on your computer and you are ready.
Troubleshooting
- If it is not working, try the steps below to reconnect the mouse and receiver.
- Turn off your mouse and re-plug in the SB receiver, turn the lower back on (make sure the channel is set on )
- Press and hold the “Connect” button (keep mouse close to receiver)
- LThe ED indicator will start flashing green for 10 seconds and turn off when disconnected
- If it does not work after 10 seconds, repeat steps 1 and 2
Connect via Bluetooth in Windows
Turn on your mouse and set it on either Bluetooth 1 ( ) or Bluetooth 2 ( )
Click on “Start” (bottom left corner of your screen)
Go to Settings
- Device
- Bluetooth & other devices
- Turn on Bluetooth
- Add Bluetooth or other device
- Add a device (Bluetooth)
Press and HOLD the “Connect” button to set the mouse in pairing mode (LED will start flashing) Click on “BT5.1 Mouse” in the list on your computer to set pairing, the LED will stop flashing and light up for 3 seconds when it is completed
Low Battery
If this LED starts blinking, it means you need to change the battery.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>