hysencontrol HY01RF Wireless Thermostat User Manual

User Manual HY01RF Wireless Thermostat

Many thanks for your selection of our products and services, and also for your trust and support to us

Product Specification

☆ Power: two AA 1.5V alkaline batteries
☆ Range of temperature display: 0~40°C/32~104°F
☆ Insulating condition: Normal environment
☆ Running program: Set per 1 week as a cycle
☆ Installation: Wall mounted or on battery seat
☆Working environment temperature: 0~70°C/32~122°F
☆Range of temperature adjustment: 5~35°C/41~95°F
☆ Display accuracy: 0.5°C or 1°F
☆ Output: Switch relay
☆ Probe sensor: NTC(10k)1%
☆ Size(mm): 1309027 And 10778*28
☆ Contact capacity: 16A/220V(RF electric heating)
5A/220V(RF gas boiler heating)
3A/220V(RF water heating)

Displays & Buttons

Operation Key

mode. At programme mode, press “+”or”-” to adjust the value, it will automatic enter into temporary manual mode
B| +| Increasing key
C| PRG| clock key: short pressing is setting clock,  long pressing is setting programme Keys locked/unlocked：press “+”and“-”at the same time for 3 seconds
D| –| Decreasing key
E| ****| Power on/off key

Run Mode

Factory Preset Mode

Interval| Monday to Friday| the default value| Saturday and Sunday| the default value| **
---|---|---|---|---|---
1st| 06:00-08:00| 20°C| 06:00-08:00| 20°C
2nd| 08:00-11:30| 15°C| 08:00-11:30| 15°C
3rd| 11:30-13:30| 15°C| 11:30-13:30| 15°C
4th| 13:30-17:00| 15°C| 13:30-17:00| 15°C
5th| 17:00-22:00| 22°C| 17:00-22:00| 22°C
6th| 22:00-06:00| 15°C| 22:00-06:00| 15°C
Mode| explain| printscreen
---|---|---
Programming mode| Press“ SET ”to switch into programme mode (As shown in picture one) Programme illustration 5+2 programme function(advanced options contain of 6+1 and 7 days programme function, you can also cancel this programme function), that is Monday to Friday is the same setting value, and Saturday to Sunday is the same setting value。Every day can be divided into 6 time interval Setting the programme value:long press“PRG” to enter into programme setting mode, then short press“PRG”to switch, press“+ ”or“-”to adjust value.|
Manual Mode| Press “SET” to enter into manual mode (As shown in picture two), press“+”or“-”to adjust value.| **
Temporary manual mode| at programme mode,press “ +” or “-” to adjust the value, it will automatic enter into temporary manual mode|

Sending condition ofThermostat

Send once for 20 minutes
Press on/off key
****Switch over output state
Communication instruction,be long bright display in normal communication and blinking display in abnormal communication

Transceiver tips
Transceiver LED display instruction:

• Power light (green light):it’s bright when power on
  Signal light(orange light):it’s long bright within 10s after power on (match IP),signal light offwhen it receive match,signal light is blinking within 10s when power off.

• Load light/fault light (red light):

A, When no fault:light on when load output,light offwhen no load output
B, When fault: light is blinking and indication when fault
Signal light blink 1 time when it does not receive 485 signal for 1 hour (light on 0.25 seconds light off 0.25 seconds), spacing out the light for 2 seconds
IP is fault(IP:FFFF),light blink 2 times (light on 0.25 seconds light off 0.25 seconds), spacing out the light for 2 seconds
Light blink 3 times when it does not receive wireless signal for 1 hour (light on 0.25 seconds light off 0.25 seconds),spacing out the light for 2 seconds
Light blink 4 times when built-out sensor is fault (light on 0.25 seconds light off 0.25 seconds), spacing out the light for 2 seconds

Advanced Options

Advanced options can be classified to two sets
MODE 1：
Turn off thermostat,long press SET for 3 seconds,it will display A01-A09,then press SET to switch between these options

1. When the setting temperature is higher than or equal to the sum of indoor temperature and the start differential temperature, the heating equipment will turn on.
2. When the indoor temperature is higher than or equal to the sum of the setting temperature and the start differential temperature, the heating equipment will turn off.
| Keypad (A03）| 0  half locked：all keys are locked except for the on-off key;
1  full locked,all keys are locked including the on-off key.
| high temperature protection (A04）| Range:35~70 When the lowest setting temperature is 35°C,press “ ”,it will display “ ”, high temperature protection function is canceled; if the indoor temperature is higher than the high temperature protection value,the heating equipment will be cut off.
| low temperature protection (A05）| Range:5°C~10°C ;When the highest setting temperature is 10°C,press “  ”,it will display “  ”, low temperature protection function is canceled; if the indoor temperature is lower than the low temperature protection value,the heating equipment will turn on.
| setting temperature lowest limiting value（A06）| Range:1°C~10°C:
| setting temperature highest limiting value （A07）| Range:30°C~70°C
| Week programme choice（A08）| WON TUE WED THU FRI SAT SUN : represent 7days programme
WON TUE WED THU FRI SAT ：represent6+1 programme
WON TUE WED THU FRI ：represent5+2 programme “ ”represent programme is canceled
| Transceiver I P check ( A 0 9 ):| Within 10 seconds after transceiver power on,press “ + ”key shortly,check transceiver .Check successfully as shown

MODE 2：
Turn off thermostat, long press “ PRG” for 3 seconds it will display B01-B08,then press “ SET” ” to switch between these options

F )
| IP low setting (b03)| Press “+ ”or“ -” key to adjust setting value ( 1 ~ F F )
| Write transceiver IP address (b04)| Within 10 seconds after transceiver power on, press“+”key to send address
| valve controlling selection (b05)| Press “ + ”or“ – ” key to adjust setting value, 0 valve is controlled by thermostat, 1 valve is not controlled by thermostat, Keep valve in closed state
| Descaling function (b06)| Press“+ ”or“-”key to adjust setting value, 0 turn off, 1 turn on Descaling function:continue to close valve for 100 hours and force to open valve for 3 minutes
| Degrees Celsius and Fahrenheit selection (b07)| 0= °C
1= °F
| Factory reset (b08)| Display Ao, long press PRG key,show all setting key and factory reset

Wiring Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>