PHENOM 55860 Rgb LED Strip Magiccontrol Instruction Manual

PHENOM 55860 RGB LED Strip Magic control

Warnings and Installation Instructions
The danger of suffocation! Please keep the packaging of the device away from children, as it may lead to suffocation. The device is for adults only and can be used, the storage location must be chosen in such a way that children cannot accidentally access it. With the device, children are not allowed to play.

The device may only be used for its intended purpose! The device may only be used by persons who have read and understood the user manual and can operate the device accordingly! Decreased persons with mental, physical or sensory disabilities may not use the device! Children do not they can use the device! The device is designed for residential use! Do not use the device if it has previously been dropped or bumped against something and it is visibly damaged! The safety devices must be used as intended, their modification or elimination is strictly prohibited!

Risk of electric shock

1. If you are not familiar with connecting electrical devices to the electrical network, ask for professional help from an electrician!
2. The control unit must NOT be operated with a free cable end! Only apply voltage to the device if you have connected all cables and made sure they are connected correctly!
3. Do not operate the device in a damp, wet environment, the power supply unit of the device should only be used indoors, in a dry place can be used. Otherwise, there is a risk of short circuit and electric shock!
4. Only operate the device with voltage according to the specification (100 – 240 V AC)!
5. Do not touch the device with wet, wet hands! Touching the device, including its cable, with wet hands is strictly prohibited!
6. Before applying voltage to the device, check the correct connection and integrity of the insulation! The wrong wiring can cause an accident-prone situation and cause material damage!
7. For safe installation of the device, fix the device! Use the self-adhesive glue included in the package!
8. Install the device so that it is not exposed to direct sunlight or heat sources!
9. It is forbidden to cover the device with any material! Do not disassemble the device. It is forbidden to modify the parameters of the device!
10. The manufacturer and the distributor are not responsible for damages resulting from improper use!

First steps, warnings

1. Before use, make sure that the LED strip and the power cable are undamaged. The LED strip is a Do not operate on a plastic drum required for safe transport!
2. The rolled-up LED strip can be damaged and defective can result in operation!
3. The device is controlled with the included remote control or via Wi-Fi using the Tuya application, please do not use near signal noise or high current, magnetic field.
4. The LED strip is IP65, the controller and power supply are IP20. Please keep it when installing the device keep these ratings in mind! It is strictly forbidden to deviate from this!
5. Do not expose the power supply unit and control unit to direct sunlight!
6. Keep away from children! Not child’s play! 6. You can shorten the light strip, cut it every 3 LEDs. Look for the lines placed at the copper connectors which cutting along is allowed.
7. After cutting, we recommend ensuring that the tape is properly insulated. Such in this case, proceed with caution during installation and subsequent use! The quality of the factory insulation is damaged, the IP classification changes!
8. If you do not use the device for a long time, please unplug the power plug and remove the battery from the from remote control. 
9. In case of failure, it is forbidden to disassemble or modify the device. Have the device repaired by a specialist.
10. The manufacturer and distributor assume no responsibility for damages resulting from incorrect installation and operation.

Device assembly

Connect the 4-cable connector of the LED strip to the connector of the control unit. At the time of connection pay attention to the correct cable sequence! Connect the “+” wire to the connection leg indicated by the arrow. Connect the DC connector of the control unit to the power supply in the box, then to the mains to a power source. (centre positive connector)

LED mounting
The power supply must be placed in a well-ventilated place protected from direct sunlight, heat and moisture. 2. Sticking the LED strip is only possible on a well-cleaned, dry, smooth surface. 3. Depending on the surface to be installed, you can use an alcohol wipe for cleaning. 4. Pull off the protective strip on the back of the LED strip. Always peel off as much as you can stick right away. Control multiple tapes simultaneously: If you have several identical LED strips, it is possible to control them with a remote control. Put it together the corresponding (4-pin) connectors.

Remote controller

1. Brightness up
2. Brightness down
3. On / off button
4. Colours  White Speed ​
5. Pre-programmed lighting effects
6. Speed ​​- 9. 1 hour / 2 hour timing
7. Light effects on ambient sounds (using the microphone in the controller)
8. Control buttons: “C” – Switching between colour modes button
9. To turn the device on and off serving button.
10. “M” – Microphone mode. By repeatedly pressing the “C” and “M” keys you can switch between individual color effects and color modes.

Application

1. Connect to local WiFi to your network!
2. Program installation: Download Play From the store or the AppStore a Tuya Smart app and install it, if you haven’t done so before.
3. If it has log in with a user account into your profile. If not If you have registered an account, please register by entering your details and then sign in.
4. When you turn on the switch, the application will automatically recognize the devices waiting to be paired.
5. Follow the instructions on the screen, add the device to your profile, name the device and set it if necessary in which room the device is located. (This can be useful in the case of several identical devices)

To download the program for your phone’s camera scan the QR code below.

If your phone does not recognize the device automatically, please turn the device off and on 5 times in a row. If the LED strip flashes red, it indicates that it has switched to pairing mode. In this case, also on the screen of your phone the device appears:

Tip: If it doesn’t appear automatically and the device, you can choose it a “Lighting” / “Lighting (Wi-Fi) device in the menu item. 5. After successful addition remotely using a smartphone the switch can also be controlled. Other, with the application settings for related information consult TuyaSmart in its description. Cleaning If accessible there is the switch and on the outer housing there is contamination, de-energize the device, then soft, dry, microfiber wipe off any with a cloth impurities. Don’t use it wet wipes! Destruction: This mark is on the product or the companion documentation indicates that it is an electrical or electronic product non-disposable household waste.

For proper disposal and reuse these products hand it over to a designated waste collection point.

By disposing of the product correctly helps to prevent the living environment and risk for human health the development of possible dangers, which waste is incorrect could result from treatment. THE more about delivery ask your local for details You are the nearest to the authority’s collection point.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>