TOMADO TRT4702W Table Model Refrigerator Instruction Manual
- May 15, 2024
- TOMADO
Table of Contents
TRT4702W
KOELKAST | REFRIGERATOR Instruction manual
REVERSING THE DOOR OPENNG
Tools you will need
REVERSING THE DOOR OPENING
The door of the appliance can be opened on the right or left side. In order to
reverse the door opening, please observe the instructions below. It would be
best to do this with two people.
Attention: switch off the thermostat and remove the plug from the socket.
Remove all items from the appliance, including the shelf, before reversing the
door opening.
- Remove the upper hinge cap.
- Using a sharp object, pry out the plug buttons.
- Remove the Philips screws that connect the upper hinge on the right side of the appliance.
- Carefully lift the door and place it on a padded surface to prevent it from scratching.
- Remove the plug and transfer it to the uncovered hole at the right side. Be sure to press the plug firmly into the hole.
- Then tilt the appliance backwards. Remove the bolts that hold the lower hinge on the right side.
- Remove the pen from the hinge. Rotate the hinge 180 degrees and place the pen back in the hinge.
- Remove the screw-type leveling front leg and transfer it to the right side.
- Secure the lower hinge. Carefully place the appliance upright again.
- Set the door into it’s new place. Make sure the door is straight in relation to the exterior of the appliance.
- Secure the upper hinge and replace the upper hinge cap. Insert the plug buttons on the uncovered holes on (right side).
- Allow the appliance to rest for 3 hours before inserting the plug in the socket.
SAFETY INSTRUCTIONS
- Please read these instructions before operating the appliance and retain for future use.
- Only use this appliance for the purposes described in the instruction. The appliance is suitable for storing food. It is possible to freeze fresh food in the freezer section.
- Only connect the appliance to alternate current, to an earthed wall socket, with a mains voltage that corresponds with the information provided on the information plate of the appliance.
- Do not use single/multiple adapters or extension cords.
- Do not use the appliance if the plug, cord or appliance are damaged, or if the appliance no longer functions properly or if it is damaged in any other way. If this is the case, consult the shop or our technical service. Never replace the plug or cord yourself.
- The appliance must be moved and installed by two or more persons.
- Be careful when moving the appliance to prevent the floor from getting damaged.
- During installation, do make sure the power cable is not damaged.
- Check that the appliance is not placed too close to a heat source.
- In order to ensure proper ventilation, a free space of 10 cm should be maintained around the appliance.
- Never cover the ventilation openings.
- Make sure the cooling pipes do not get damaged.
- Install the appliance on a sturdy, flat and stable surface.
- Install the appliance in a dry and well ventilated room. The appliance is intended for use in a room where the ambient temperature falls within the applicable class, depending on the climate class found on the information plate on the back of the appliance.
Climatic class | Ambient temperature |
---|---|
SN | From 10°C to 32°C |
N | From 16°C to 32°C |
ST | From 16°C to 38°C |
T | From 16°C to 43°C |
-
Do not store explosive or highly flammable substances in the appliance. The vapours could cause a fire hazard or an explosion.
-
Do not store glass bottles or jars with liquids in the freezer, as they could break when frozen.
-
Do not use mechanical, electrical or chemical agents to speed up the defrosting process.
-
Make sure that children are unable to play with the appliance, such as hide in it. This is dangerous.
-
Keep the appliance out of reach of children. Children do not see the dangers when handling electrical appliances. Therefore, never allow children to work with electrical appliances without supervision. Keep the appliance and cord out of reach of children younger than 8 years of age.
Note: Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances. -
The appliance can be used by children of 8 years and older and persons with a limited physical, sensory or mental capacity or lack of experience or knowledge, provided they use the appliance under supervision or have been instructed about its safe use and understand the hazards involved.
-
The appliance may not be cleaned or maintained by children, unless this is done under supervision.
-
Repairs to electrical appliances should only be performed by skilled persons. It is dangerous to perform a repair whereby the base unit of the appliance must be opened.
-
Only use and store the appliance indoors.
-
Never bend the power cord sharply or allow it to run across hot parts.
-
Always remove the plug from the socket when the appliance must be cleaned or repaired.
-
Never use the appliance with parts that are not recommended or supplied by the manufacturer.
-
Do not pull the cord and/or appliance to remove the plug from the wall socket. Never touch the plug with wet or moist hands.
-
Be careful with ice cubes and ice pops. If these are consumed directly out of the freezer, there is a risk of frostbite.
-
Never submerge the appliance, cord or plug in water.
-
The appliance cannot be used with a timer or separate remote control.
-
This appliance is only suitable for household use. If the appliance is not used as intended, no compensation can be claimed in case of defects or accidents and the warranty will be invalidated.
-
If you decide not to use the appliance any more due to a defect, we recommend cutting off the cord after removing the plug from the wall socket. Household appliances are not normal waste. Take the appliance to the waste processing department concerned of your municipality.
Refrigerant
The refrigerant isobutene (R600a) is contained within the refrigerant circuit
of the appliance, a natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, ensure that none of
the components of the refrigerant circuit becomes damaged. The refrigerant
(R600a) is flammable.
WARNING: Refrigerators contain refrigerant and gases in the insulation.
Refrigerant and gases must be disposed of professionally as they may cause eye
injuries or ignition. Ensure that tubing of the refrigerant circuit is not
damage prior to proper disposal.
WARNING: Risk of fire/ flammable materials
If the refrigerant circuit should be damaged:
– Avoid open flames and sources of ignition.
– Thoroughly ventilate the room in which the appliance is situated.
It is dangerous to alter the specifications or modify this product in any way.
Any damage to the cord may cause a shortcircuit, fire, and/or electric shock.
PRODUCT DESCRIPTION
- Freezer compartment
- Thermostat
- Door compartments
- Bottle compartment
- Adjustable feet
- Vegetable drawer
- Glass shelf
PRIOR TO FIRST USE
Before using the appliance for the first time, you should proceed as follows:
carefully unpack the appliance and remove all packaging material and any
promotional stickers. Keep the packaging (plastic bags, polystyrene and
cardboard) out of the reach of children. After unpacking the appliance, check
it for external damage that may have occurred during transport.
Place the appliance on a sturdy, flat surface and make sure there is enough
space all around for sufficient ventilation. A minimum space of 10 cm is
required between the appliance and the surrounding walls. In this way the
appliance is able to release heat properly, cool well and function in an
energy efficient way. You can use the adjustable feet to level the appliance.
Do not place the appliance near heat sources such as central heating or a
stove. Do take note of the climate class of the appliance. When placed in a
room that is too cold, the refrigerator will not function properly.
After placing the appliance, leave it for at least 3 hours before inserting
the plug in the socket.
First clean the interior of the appliance. Use warm soapy water with, for
instance, washing-up liquid, all-purpose cleaner or soda. Wipe the inside of
the appliance after cleaning with clean water and properly wipe everything
dry. Leave the appliance to dry for 1 to 2 hours.
USE
The control unit of the appliance is located at the back of the appliance.
Check that the thermostat is in position OFF.
Check that the voltage corresponds with what is stated on the information
plate and insert the plug in the socket.
Adjusting the temperature
By means of the thermostat you are able to switch on the appliance and change
the temperature in the refrigerator.
The possible positions of the thermostat:
Position OFF | – no cooling, but there is power |
---|---|
Position 1/2 | – highest temperature, least cold |
Position 3 | – optimum temperature |
Position 4 | – lowest temperature, coldest |
Set the temperature with the thermostat and select a position between 1 and 4.
We recommend setting the appliance to position 3. The appliance will now cool
continuously until the set temperature has been reached. Allow the appliance
to reach the required temperature with no food. Usually this will take 2 to 3
hours. After that, you can set the thermostat to the required position and
fill the appliance with food.
To switch the appliance off, set the thermostat to position OFF and unplug the
appliance.
Attention:
The ambient temperature, the frequency of opening the door and the position of
the appliance have an effect on the temperature in the appliance. Take this
into account when setting the thermostat.
- Do not place hot food in the appliance.
- You should never place hazardous, highly flammable or explosive substances such as alcohol, acetone or petrol in the appliance, because there will be a hazard of explosion.
- Carefully package meat and fish to prevent unpleasant smells.
- Do not place food items in contact with the cold wall at the back of the appliance.
- Leave sufficient space between the different foods, to allow the air to circulate properly.
- Do not leave the door open for longer than necessary.
TIPS
- High ambient temperatures have a negative effect on energy use. Keep the appliance in a position away from direct sunlight or other sources of heat.
- Keep ventilation openings free. Clogged openings lead to higher use of energy.
- Try not to open the door too often, especially when the weather is wet and hot. Once you open the door, mind to close it as soon as possible.
- Turn the thermostat to a lower setting when the circumstances allow it.
- Before storing fresh cooked food, make sure the food has cooled at least to room temperature.
- Ice and frost layer increase energy consumption, so clean the appliance as soon as the layer is 3 to 5 mm thick.
- If the gasket is damaged or if it turns out that the sealing is poor, the energy consumption is substantially higher. To restore efficiency, replace the gasket.
- Always consider the instructions, otherwise the energyconsumption is substantially higher.
To avoid contamination of food, please respect the following instructions
– Opening the door for long periods can cause a significatn increase of the temperature in the compartments of the appliance.
– Clean regularly surfaces that can come in contact with food and accessible drainage systems.
– Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
– Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making icecream and making ice cubes.
– One-, two- and three-start compartments are not suitable for the freezing of fresh food.
Order| Compartments TYPE| Target storage temp. [°C]|
Appropriate food
---|---|---|---
1| Fridge| +2 — +8| Eggs, cooked food, packaged food, fruits and vegetables,
dairy products, cakes, drinks and other foods are not suitable for freezing.
2| (*)-Freezer| 5-18| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
3| -Freezer| 5-18| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
4| *-Freezer| 5-12| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
5| -Freezer| <-6| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
6| 0-star| -6 — 0| Fresh pork, beef, fish, chicken, some packaged processed
foods, etc. (Recommended to eat within the same day, preferably no more than 3
days).
Partially encapsulated processed foods (non-freezable foods).
7| Chill| -2 — +3| Fresh/ frozen pork, beef, chicken, freshwater aquatic
products, etc. (7 days below 0°C and above 0°C is recommended for consumption
within that day, preferably no more than 2 days). Seafood (less than 0 for 15
days, it is not recommended to store above 0°C.
8| Fresh food| 0 — +4| Fresh pork, beef, fish, chicken, cooked food, etc.
(Recommended to eat within the same day, preferably no more than 3 days)
9| Wine| +5 —+20| Red wine, white wine, sparkling wine, etc.
Note: please store different foods according to the compartments or
target storage temperature of your purchased products.
– If the refrigerating appliance is left empty for long periods, switch off,
defrost, clean, dry, and leave the door open to prevent mould developing
within the appliance.
Water dispenser cleaning (special for water dispenser products):
– Clean water tanks if they have not been used for 48 h; flush the water
system connected to a water supply if water has not been drawn for 5 days.
WARNING -Food needs to be packed in bags before putting into the
refrigerator, and liquids need to be packed in bottles or capped containers to
avoid the problem that the product design structure is not easy to clean.
DEFROSTING
Defrost the freezer compartment when the layer of ice reaches a thickness of 3
to 5 mm.
Turn the thermostat to position OFF and unplug the appliance. Remove all
products from the freeze compartment.
Keep the contents of the freezer in a cool place and wrapped in blankets or
newspapers.
Place a container under the freezing compartment and wait for the ice to
defrost. You can speed up the defrosting process by placing a bowl of hot
water in the freezer.
Remove the ice with an ice scraper. Warning: Never remove the ice with the aid
of sharp objects, defrost sprays, a hair-drier, a heater, or similar items.
This may lead to unsafe situations and may cause irreparable damage to the
appliance.
Clean and dry the freezer comparment. Switch the thermostat on to the right
setting. When the freezer compartment reaches its correct temperature, replace
the food items.
CLEANING AND MAINTENANCE
Regularly clean the refrigerator to ensure proper operation. Before cleaning,
switch off the appliance by setting the thermostat to the OFF position and
unplugging the appliance.
Remove the food. Clean the interior of the appliance. Use warm water and a
neutral detergent, such as baking soda, to prevent any bad smells occurring.
Use two tablespoons and a quart liter of warm water. After cleaning, rinse the
interior with clean water and leave the door open to let it air dry for 1 to
2 hours before the power is turned on. Be careful not to affect the electrical
insulation properties when rinsing with water.
For areas that are difficult to clean in the refrigerator, such as narrow gaps
or corners, it is recommended to wipe them regularly with a soft rag, soft
brush, etc. When necessary use some auxiliary tools, such as thin sticks
(tooth picks), to ensure no contamination can accumulate in these areas.
Clean the outside of the refrigerator and the door gasket with mild soap and
water. Use a soft moist cloth.
We recommend that you dust the back of the appliance and on the floor with a
cloth or vacuum cleaner once a year in order to maintain a good output and low
energy consumption.
Do not use hard brushes, cleaning steel wire balls, wire brushes, abrasives,
such as toothpastes, organic solvents (such as alcohol, acetone, oils, etc.),
boiling water, acid or alkaline items to clean the refrigerator considering
that this may damage the appliance surface and interior. Boiling water and
benzene may deform or damage plastic parts.
RESOLVING FAILURES YOURSELF
Breakdown | Cause | Solution |
---|---|---|
The appliance no longer works | There is an interruption in the power supply. |
– check that the plug is properly inserted in the socket – check that the
power cable is not damaged
– check that there is voltage on the socket by connecting a different
appliance, such as a night lamp
Temperature in the freezer is too high or too low| Wrong setting of the
thermostat.| – turn the thermostat to a different position
The ambient temperature is higher or lower than the
temperature indicated in the table with technical data.| The appliance is
intended for operation in an
ambient temperature indicated in the table with technical data supplied with
the appliance.
The appliance is located in direct sunlight or near a heat source.| Change the
location of the appliance according to the information in the instruction
manual.
The ventilation at the rear of the appliance is hindered.| Keep the appliance
10 cm away from the walls, for sufficient ventilation.
The door of the freezer is opened too frequently or remains open for too
long.| Open the door less often and/or reduce the time that the door remains
open.
The door is not closed properly.| Make sure the foods are placed in such a way
that they do not hinder the door when it is being closed.
The compressor does not work often enough.| Check that the ambient temperature
is not lower than the range of the climate class.
The door rubber is loose.| Fasten the door rubber or have it replaced.
The appliance is working continuously.| Wrong setting of the thermostat.| –
turn the thermostat to a higher position
Unusual or loud noises| The appliance is not level and stable.| Level the
appliance with the adjustable feet.
The appliance is standing against something.| Place the appliance in such a
way that it is not standing against anything.
During normal use of the cooling appliance, different types of noises can
occur that do not have any effect on the correct operation of the appliance.
Noises that can be easily remedied:
- Noise due to the fact that the appliance is not level – position the appliance using the front adjustable feet. If necessary, place soft material under the rear wheels, particular in case of a tiled floor.
- Friction against other furniture – move the appliance.
- Grinding of drawers or shelves – remove the shelf or drawer and then place it back.
- Noise of colliding bottles – place the bottles apart.
Noises that can be heard during normal use of the appliance are caused by the operation of the thermostat, compressor (activation), cooling system (shrinkage and expansion of the material under the influence of temperature differences and flow of cooling liquid).
ORDERING ACCESSORIES
Go to www.tomado.com/support to purchase
accessories or spare parts.
WARRANTY CONDITIONS
A 24 month warranty is provided for this product. Your warranty is valid if
the product has been used in accordance with the user instructions and for the
purpose for which it was made. Also the original proof of purchase must be
submitted, stating the date of purchase, the name of the retailer and the item
number of the product. For extensive warranty information you are referred to
our website: www.tomado.com/support
TRT4702W
Tomado Electric Appliances
Postbus 159
6920 AD Duiven
The Netherlands
support@tomado.com
www.tomado.com
Modifications and printing errors reserved
TOMADO.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>