Origin 21 VS26EK-W Vertical Standard Extender Kit Instruction Manual

June 9, 2024
Origin 21

Origin 21 VS26EK-W Vertical Standard Extender Kit
logo

Origin 21 VS26EK-W Vertical Standard Extender Kit

Questions, problems, missing parts?
Before returning to your retailer, call our customer service department at 888-251-1026, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.

PACKAGE CONTENTS

Origin 21 VS26EK-W Vertical Standard Extender Kit 01

PART DESCRIPTION QUANTITY
A 26-IN Vertical Standard 1
DD Universal Wall Clip 2
EE Bottom Mount Wall Clip 1
FF Extender Bracket 1

HARDWARE CONTENTS

Origin 21 VS26EK-W Vertical Standard Extender Kit 03
Origin 21 VS26EK-W Vertical Standard Extender Kit 04

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

  • Please confirm all parts are correct before starting the assembly process.
  • Please read all instructions carefully before beginning.

WARNING

  • Do not allow children to climb or play in, on, or around this product.
  • Do not alter this product in any manner.
  • Failure to obey installation instructions and warnings can result in injury or death.
  • Use correct hardware for your specific wall type, the hardware provided is intended for 1/2 inch drywall.
  • Horizontal and Vertical Standards must be firmly secured to the wall.
  • Do not overload.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included):
Tape Measure, #2 Phillips Screwdriver, Pencil, Drill Bits (1/8” & 5/16”), Drill, LevelOrigin 21 VS26EK-W Vertical Standard Extender Kit
05

Tools Recommended for Assembly (not included): Step Ladder, Stud Finder, Rubber MalletOrigin 21 VS26EK-W Vertical Standard Extender Kit
06

Find helpful install videos and tips at lowes.com

ASSEMBLY INSTRUCTIONS

  1. Insert the Bottom Mount Wall Clip (EE) into the 26-IN Vertical Standard (A) with tab facing down. Fasten the Bottom Mount Wall Clip with M4 x 8 screws (CC).
    Hardware Used Origin 21 VS26EK-W Vertical Standard Extender Kit
07
    Origin 21 VS26EK-W Vertical Standard Extender Kit 08

  2. Insert the Extender Bracket (FF) into your existing Vertical Standard (sold separately). Fasten the Extender Bracket (FF) with a M4 x 8 screw (CC).
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 09
    Origin 21 VS26EK-W Vertical Standard Extender Kit 10 NOTE:
    Vertical Extender Kit can be used to extended an existing Vertical Standard or installed directly on to existing Horizontal Top Track as a shorter Vertical Standard.

  3. With the Extender Bracket (FF) installed, mark the hardware hole location.
    Origin 21 VS26EK-W Vertical Standard Extender Kit 11

  4. Remove the Extender Bracket (FF) and using 5/16″ drill bit, pre-drill marked hole locations into drywall. Then install Drywall Anchor (AA) into pre-drilled drywall holes. Do not drill through the metal bracket.
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 12
    Origin 21 VS26EK-W Vertical Standard Extender Kit 13 PRO TIP

    • If you are unsure if a stud is located behind markings, use 1/8″ drill bit to drill all holes. If no stud is present, then use 5/16″ drill bit to make holes larger for drywall anchors.
    • Use a rubber mallet to lightly tap Drywall Anchors (AA) into the drywall.
  5. Re-insert the Extender Bracket (FF) into your existing Vertical Standard (sold separately). Fasten the Extender Bracket (FF) with M4 x 8 screws (CC).
    Hardware Used Origin 21 VS26EK-W Vertical Standard Extender Kit
14
    Origin 21 VS26EK-W Vertical Standard Extender Kit 15

  6. Secure the Vertical Standard Connector (FF) to wall using 4.8 x 38 Panhead Screw (BB), then slide the 26-IN Vertical Standard (A) onto the Extender Bracket (FF).
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 16
    Origin 21 VS26EK-W Vertical Standard Extender Kit 17

  7. Use a Level to make sure the 26-IN Vertical Standard (C) are straight. Then mark hole locations of the Bottom Mount Wall Clips (EE).
    Origin 21 VS26EK-W Vertical Standard Extender Kit 18

  8. Remove the 26-IN Vertical Standards (A) to reveal the marks made in the previous step. Using 5/16” drill bit to pre-drill holes into drywall. Then, install Drywall Anchors (AA) into pre-drilled drywall holes.
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 19
    Origin 21 VS26EK-W Vertical Standard Extender Kit 20 PRO TIP

    • If you are unsure if a stud is located behind markings, use 1/8″ drill bit to drill all holes. If no stud is present, then use 5/16″ drill bit to make holes larger for drywall anchors.
    • PRO TIP Use a rubber mallet to lightly tap Drywall Anchors (AA) into the drywall.
  9.  Fasten 26-IN Vertical Standard (A) to the Vertical Standard Connector (FF) with M4 x 8 screws (CC).
    Origin 21 VS26EK-W Vertical Standard Extender Kit 21
    Origin 21 VS26EK-W Vertical Standard Extender Kit 22

  10. Secure the 26-IN Vertical Standard (A) to wall through the Bottom Mount Wall Clip (EE) using 4.8 x 38 Panhead Screw White (BB).
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 23
    Origin 21 VS26EK-W Vertical Standard Extender Kit 24

  11. Insert the Universal Wall Clip (DD) into both sides of the 26-IN Vertical Standards (A) near its center point. Once inserted push clips up and mark the hardware hole locations.
    Hardware Used
    Origin 21 VS26EK-W Vertical Standard Extender Kit 25
    Origin 21 VS26EK-W Vertical Standard Extender Kit 26 NOTE:
    Ensure Universal Wall Clip is installed in upward direction for maximum support.

  12. Remove Universal Wall Clip (DD) and using 5/16″ drill bit, pre-drill marked hole locations into drywall. Do not drill through the metal brackets.
    Origin 21 VS26EK-W Vertical Standard Extender Kit 27 PRO TIP

    • If you are unsure if a stud is located behind markings, use 1/8″ drill bit to drill all holes. If no stud is present, then use 5/16″ drill bit to make holes larger for drywall anchors.
  13.  Install Drywall Anchors (AA) into pre-drilled drywall holes.
    Origin 21 VS26EK-W Vertical Standard Extender Kit 28
    Origin 21 VS26EK-W Vertical Standard Extender Kit 29 PRO TIP

    • Use a rubber mallet to lightly tap Drywall Anchors (AA) into the drywall.
  14. Re-install each Universal Wall Clip (DD) into the 26-IN Vertical Standard (A) at marked hole locations and secure Clips to wall using 4.8 x 38 Panhead Screw White (BB).

Hardware Used
Origin 21 VS26EK-W Vertical Standard Extender Kit 30
Origin 21 VS26EK-W Vertical Standard Extender Kit 31

OPERATING INSTRUCTIONS

Example 26-IN Vertical Standard Kit Layouts Origin 21 VS26EK-W Vertical
Standard Extender Kit 32
Origin 21 VS26EK-W Vertical Standard Extender Kit 33

CARE AND MAINTENANCE

  • Use a soft, clean cloth that will not scratch the surface when dusting.
  •  Make sure all bolts/screws are tightly fastened before the unit is used, check bolts/screws periodically and tighten them if necessary.

WARRANTY

This limited warranty covers the original purchase of this product used for normal personal or household us. Origin 21 warrants its products will be free from defects in materials and workmanship (normal wear and tear excepted), for a period of one (1) year from the date of purchase, except as provided below. As the exclusive remedy under this warranty, Origin 21 will repair or replace any defective component. This warranty does not apply to damage caused by fire, accident, negligence, misuse, use other than as stated in product instructions, improper cleaning or other circumstances not directly attributable to defects in materials and workmanship. Materials are warranted for one year from date of purchase. Proof of purchase is required in the form of a receipt (copy or original) to validate the warranty.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 888-251-1026, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com.
Origin 21 VS26EK-W Vertical Standard Extender Kit 34
Origin 21 VS26EK-W Vertical Standard Extender Kit 35

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Origin 21 User Manuals

Related Manuals