Supermicro 221H-TN24R Hyper SuperServer User Manual

Supermicro 221H-TN24R Hyper SuperServer

Product Information

Specifications:

• Model: SuperServer 221H-TN24R
• Form Factor: Tower
• Processor Support: Dual Intel Xeon Scalable Processors
• Memory Support: Up to 4TB DDR4 ECC RDIMM/LRDIMM
• Storage: Supports NVMe SSDs and SATA drives
• Expansion Slots: PCIe 5.0 x16, PCIe 5.0 x8, M.2 slots
• Networking: Gigabit Ethernet
• Power Supply: Dual PSU support

Product Usage Instructions

Installation:

1. Place the SuperServer on a stable surface.
2. Open the chassis to access the internal components.
3. Install the CPU(s) following the manufacturer’s instructions.
4. Insert memory modules into the appropriate DIMM slots.
5. Connect storage devices to the NVMe and SATA connectors.
6. Ensure all power connectors are properly connected.

Powering On:

1. Connect the power cords to the PSUs and a power source.
2. Press the power button on the front panel to turn on the SuperServer.
3. Check for LED indicators to ensure proper power and system operation.

BIOS Configuration:

1. Access the BIOS settings by pressing the designated key during startup.
2. Configure boot order, system time, and other settings as needed.
3. Save changes and exit the BIOS setup utility.

Maintenance:

1. Regularly clean dust from fans and components to prevent overheating.
2. Check for software updates and firmware upgrades periodically.
3. Monitor system temperatures and performance for any abnormalities.

Frequently Asked Questions (FAQ):

• Q: How many PCIe slots are available on the SuperServer?
  A: The SuperServer has multiple PCIe slots including PCIe 5.0 x16, PCIe 5.0 x8, and M.2 slots for expansion.

• Q: What is the maximum memory capacity supported?
  A: The SuperServer supports up to 4TB of DDR4 ECC RDIMM/LRDIMM memory.

• Q: How do I clear the CMOS on the SuperServer?
  A: To clear the CMOS, locate the CMOS clear jumper on the motherboard and move it to the clear position for a few seconds before moving it back.

Board Layout

Memory Support

System Information

Each system comes with a unique default password for the ADMIN user. This can be found on a sticker on the motherboard and a sticker underneath the service tag on chassis. If necessary, the password can be reset by the Supermicro IPMICFG tool.
For more information, please visit: https://www.supermicro.com/en/solutions /management-software/bmc-resources.

**Caution and Product Resources

**

SAFETY INFORMATION: IMPORTANT: See installation instructions and safety warning before connecting system to power supply. http://www.supermicro.com/about/policies/safety_information.cfm.
WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets. If any CPU socket empty, install protective plastic CPU cap.
CAUTION: Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the systemwill not operate.
CAUTION: This unit has redundant power sources. Please disconnect all the power cords before servicing.
PRODUCT RESOURCES:
For more information go to: http://www.supermicro.com/support

CPU Installation

1. Put processor into bracket – attention to the lineup Pin and key on both processor and carrier.
2. Put processor carrier module into HS.
3. Put processor heatsink module into MB.

OVERVIEW

Front View

Rear View

NVMe Drive Bay Cable Routing

Storage AOC Drive Bay Cable Routing

References

• Terms and Conditions | Supermicro
• Support | Supermicro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>