makita DTW300 Cordless Impact Wrench Instruction Manual

makita DTW300 Cordless Impact Wrench

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
  WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire.

Intended use

The tool is intended for fastening bolts and nuts.

Noise
The typical A-weighted noise level is determined according to EN62841-2-2:

Model DTW300

• Sound pressure level (LpA) : 97 dB(A) Sound power level (LWA) : 108 dB (A) Uncertainty (K) : 3 dB(A)
  Model DTW301

• Sound pressure level (LpA) : 97 dB(A) Sound power level (LWA) : 108 dB (A) Uncertainty (K) : 3 dB(A)
  Model DTW302

• Sound pressure level (LpA) : 94 dB(A) Sound power level (LWA) : 105 dB (A) Uncertainty (K) : 3 dB(A)

NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.

• WARNING: Wear ear protection.
• WARNING: The noise emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
• WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) is determined according to EN62841-2-2:

• Model DTW300
  Work mode: impact tightening of fasteners of the maximum capacity of the tool
  Vibration emission (ah) : 12.5 m/s2
  Uncertainty (K) : 1.5 m/s2

• Model D TW301
  Work mode: impact tightening of fasteners of the maximum capacity of the tool
  Vibration emission (ah) : 12.5 m/s2
  Uncertainty (K) : 1.5 m/s2

• Model DTW302
  Work mode: impact tightening of fasteners of the maximum capacity of the tool
  Vibration emission (ah) : 15.4 m/s2
  Uncertainty (K) : 2.4 m/s2

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

• WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
• WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

SAFETY WARNINGS

General power tool safety warnings
WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instruct options for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Cordless impact wrench safety warnings

1. Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

2. Wear ear protectors.

3. Check the impact socket carefully for wear, cracks or damage before installation.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Do not touch the impact socket, bolt, nut or the workpiece immediately after operation. They may be extremely hot and could burn your skin.

7. Always be sure you have a firm footing.
   Be sure no one is below when using the tool in high locations.

8. The proper fastening torque may differ depending upon the kind or size of the bolt. Check the torque with a torque wrench.

9. Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the tool.
   WARNING: DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to safety rules for the subject product.
   MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

Important safety instructions for battery cartridge

1. Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.

2. Do not disassemble or tamper with the battery cartridge. It may result in a fire, excessive heat, or explosion.

3. If the operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

6. Do not touch the terminals with any conductive material.

7. Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.

8. Do not expose the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

9. Do not store and use the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).

10. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

11. Do not nail, cut, crush, throw, drop the battery cartridge, or hit a hard object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.

12. Do not use a damaged battery.

13. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
    For commercial transports e.g. by third parties or forwarding agents, the special requirements on pack-aging and labeling must be observed.
    For the preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations.
    Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.

14. When disposing of the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to the disposal of batteries.

15. Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.

16. If the tool is not used for a long period of time, the battery must be removed from the tool.

17. During and after use, the battery cartridge may take on heat which can cause burns or low-temperature burns. Pay attention to the handling of hot battery cartridges.

18. Do not touch the terminal of the tool immediately after use as it may get hot enough to cause burns.

19. Do not allow chips, dust, or soil to stuck into the terminals, holes, and grooves of the battery cartridge. It may result in poor performance or breakdown of the tool or battery cartridge.

20. Unless the tool supports the use near
    high-voltage electrical power lines, do not use the battery cartridge near high-voltage electrical power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.

21. Keep the battery away from children.
    CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
4. When not using the battery cartridge, remove it from the tool or the charger.
5. Charge the battery cartridge if you do not use it for a long period (more than six months).

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking the function on the tool.

Installing or removing the battery cartridge
CAUTION: Always switch off the tool before installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery cartridge firmly when installing or removing the battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury. Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator as shown in the figure, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

Tool/battery protection system

The tool is equipped with a tool/battery protection system. This system automatically cuts off the power to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions:

Overload protection
This protection works when the tool is operated in a manner that causes it to draw an abnormally high current. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.

Overheat protection
This protection works when the tool or battery is over-heated. In this situation, let the tool and battery cool before turning the tool on again.

Over-discharge protection
This protection works when the remaining battery capacity gets low. In this situation, remove the battery from the tool and charge the battery.

Indicating the remaining battery capacity
Only for battery cartridges with the indicator Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds. NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when the battery protection system works.

Switch action

Fig.3: 1. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
NOTE: The tool automatically stops when you keep pulling the switch trigger for 6 minutes.
NOTE: When full speed mode is turned on, the rotation speed becomes fastest even if you do not pull the switch trigger fully.
For detail information, refer to the section of full-speed mode.

Electric brake
This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service center.

Lighting up the front lamp
CAUTION: Do not look in the light or see the source of light directly. Fig.4: 1. Lamp Fig.5: 1. Button To turn on the lamp status, press the button for one second. To turn off the lamp status, press the button for one second again.
With the lamp status ON, pull the switch trigger to turn on the lamp. To turn off, release it. The lamp goes out approximately 10 seconds after releasing the switch trigger.
With the lamp status OFF, the lamp does not turn on even if pulling the trigger.

• NOTE : To confirm the lamp status, pull the trigger. When the lamp lights up by pulling the switch trigger, the lamp status is ON. When the lamp does not come on, the lamp status is OFF.
• NOTE: When the tool is overheated, the light flashes for one minute, and then the LED display goes off. In this case, cool down the tool before operating again.
• NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
• NOTE: While pulling the switch trigger, the lamp status cannot be changed.
• NOTE: The lamp status can be changed within approximately 10 seconds after releasing the switch trigger.

Reversing switch action

Fig.6: 1. Reversing switch lever

• CAUTION: Always check the direction of rotation before operation.
• CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
• CAUTION: When not operating the tool, always set the reversing switch lever to the neutral position.

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A-side for clockwise rotation or from the B side for counterclockwise rotation.
When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

Changing the application mode

Changing the impact force
You can change the impact force in four steps: 4 (max), 3 (hard), 2 (medium), and 1 (soft).
This allows a tightening suitable to the work.
The level of the impact force changes every time you press the button .
You can change the impact force within approximately one minute after releasing the switch trigger.
NOTE: You can extend the time to change the impact force by approximately one minute if you press the button or  Fig.7

The lamp is on.
Example of application

Application mode

(Impact force grade displayed on panel)

| Example of application
---|---
4 (Max)| Assembling steel frames and tightening long screws or bolts.
3 (Hard)| Assembling steel frames.
Application mode

(Impact force grade displayed on panel)

| Example of application
---|---
2 (Medium)| Assembling or disassembling scaffolds and frameworks.
1 (Soft)| Assembling furniture.

NOTE : When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button.
NOTE : All lamps on the switch panel go out when the tool is turned off to save the battery power. The impact force grade can be checked by pulling the switch trigger to the extent that the tool does not operate.

Changing the application mode
This tool employs several easy-to-use application modes for driving bolts with good control.
The type of the application mode changes every time you press the button.
You can change the application mode within approximately one minute after releasing the switch trigger.
NOTE: You can extend the time to change the application mode by approximately one minute if you press the button or Fig.8

Application mode (Assist type displayed on panel)| Feature| Purpose
---|---|---
Bolt mode| Clockwise

This mode helps to repeat screwdriver continuously with equal torque. This mode

also helps to reduce the risk of breakage of bolts/nuts due to overtightening.

Counterclockwise

This mode helps to prevent a bolt from falling off. When loos- ening a bolt with the tool driving in counterclockwise rotation, the tool automatically stops or slows down after the bolt/nut gets enough loosened.

NOTE:

The timing to stop the driving varies depending on the type of the bolt/nut and the material to be driven. Make a test driving before using this mode.

| Clockwise

Preventing overtightening of bolts.

Counterclockwise

Loosening bolts.

Bolt mode (1)| Clockwise

The tool stops automatically as soon as it has started impact blows.

Counterclockwise

The impact force is 4. The tool stops automatically as soon as it has stopped impact blows.

| –
Bolt mode (2)| Clockwise

The tool stops automatically approximately 0.5 second later from the moment that the tool has started impact blows.

Counterclockwise

The impact force is 4. The tool stops automatically approximately 0.2 second later from the moment that the tool has stopped impact blows.

| –
Application mode (Assist type displayed on panel)| Feature| Purpose
---|---|---
Bolt mode (3)| Clockwise

The tool stops automatically approximately 1 second later from the moment that the tool has started impact blows.

Counterclockwise

The tool slows down the rotation after it has stopped impact blows.

| –

NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button.
NOTE: All lamps on the switch panel go out when the tool is turned off to save the battery power. The type of the application mode can be checked by pulling the switch trigger to the extent that the tool does not operate.

Full speed mode

Fig.9: 1. Button 2. Lamp
When full speed mode is turned on, the tool speed becomes fastest even if you do not pull the switch trigger fully. When full speed mode is turned off, the tool speed increases as you increase the pressure on the switch trigger.
To turn on full speed mode, press and hold the button . To turn off full speed mode, press and hold the button again.
The lamp turns on while full speed mode is on.
NOTE: Full speed mode continues even after switching the impact force mode/auto-stop mode.

ASSEMBLY

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Selecting the correct impact socket
Always use the correct size impact socket for bolts and nuts. An incorrect size impact socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut.

Installing or removing the impact socket
CAUTION: Make sure that the impact socket and the mounting portion are not damaged before installing the impact socket.
CAUTION: After inserting the impact socket, make sure that it is firmly secured. If it comes out, do not use it.
NOTE: The way of impact socket installation varies depending on the type of square drive on the tool.

Tool with the ring spring
For impact socket without O-ring and pin
Model DTW300, DTW302 Fig.10: 1. Impact socket 2. Square drive 3. Ring spring
Push the impact socket onto the square drive until it locks into place.
To remove the impact socket, simply pull it off.

For impact socket with O-ring and pin
Model DTW300 Fig.11: 1. Impact socket 2. O-ring 3. Pin

Move the O-ring out of the groove in the impact socket and remove the pin from the impact socket. Fit the impact socket onto the square drive so that the hole in the impact socket is aligned with the hole in the square drive.
Insert the pin through the hole in the impact socket and square drive. Then return the O-ring to the original position in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation procedures in reverse.

A tool with the detent pin
Model DTW301 Fig.12:

1. Impact socket
2. Hole
3. Square drive 4. Detent pin

Align the hole in the side of the impact socket with the detent pin on the square drive and push the impact socket onto the square drive until it locks into place. Tap it lightly if required.
To remove the impact socket, simply pull it off. If it is hard to remove, depress the detent pin while pulling the impact socket.

Installing hook

CAUTION: When installing the hook, always secure it with the screw firmly. If not, the hook may come off from the tool and result in personal injury.
CAUTION: Use the hanging/mounting parts for their intended purposes only. Using for the intended purpose may cause accidents or personal injury. Fig.13:

1. Groove 2. Hook 3. Screw
   The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out.

OPERATION

CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Fig.14
Hold the tool firmly and place the impact socket over the bolt or nut. Turn the tool on and fasten for the proper fastening time.
The proper fastening torque may differ depending upon the kind or size of the bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures.
Proper fastening torque for a standard bolt

1. Fastening time (second)
2. Fastening torque

Proper fastening torque for high tensile bolt

1. Fastening time (second)
2. Fastening torque

• NOTE: Hold the tool pointed straight at the bolt or nut.
• NOTE : Excessive fastening torque may damage the bolt/nut or impact socket. Before starting your job, always perform a test operation to determine the proper fastening time for your bolt or nut.
• NOTE: If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery cartridge.

The fastening torque is affected by a wide variety of factors including the following. After fastening, always check the torque with a torque wrench.

1. When the battery cartridge is discharged almost completely, the voltage will drop and the fastening torque will be reduced.
2. Impact socket
   • Failure to use the correct size impact socket will cause a reduction in the fastening torque. A worn impact socket (wear on the hex end or square end) will cause a reduction in the fastening torque.
3. Bolt
   • Even though the torque coefficient and the class of bolt are the same, the proper fasten-ing torque will differ according to the diameter of bolt.
   • Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque coefficient, the class of bolt and the bolt length.
4. The use of the universal joint or the extension bar somewhat reduces the fastening force of the impact wrench. Compensate by fastening for a longer period of time.
5. The manner of holding the tool or the material of the driving position to be fastened will affect the torque.
6. Operating the tool at low speed will cause a reduction in the fastening torque.

MAINTENANCE

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

• Impact socket
• Extension bar (for DTW300, DTW301)
• Universal joint (for DTW300, DTW301)
• Socket bit adapter (for DTW300, DTW301)
• Tool hanger
• Makita genuine battery and charger
  NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.

References

• MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>