Panasonic ET-LAF100A Replacement Lamp Unit Instruction Manual

: June 9, 2024
: Panasonic

Table of Contents

Read This First
Documents / Resources

Panasonic ET-LAF100A Replacement Lamp Unit Instruction Manual

Read these instructions completely before operating this unit.

Thank you for purchasing a Panasonic product.
Before using this product, be sure to read [Read this first!]

Read This First

WARNING

Remove the power plug before replacing the lamp unit.
- If the lamp unit is replaced without removing the power plug. electric shocks and breakage may Occur.
Wait until the lamp is cooled sufficiently before replacing the lamp unit (wait one hour or longer).
- The lamp cover gets very hot, and contact with it can cause burns.
Do not remove any screws (such as the black screws) other than those indicated when replacing the lamp unit.
- If this is not observed. electric shocks, burns or other injuries may occur.

Notes on replacing the lamp unit

The light source lamp is a glass component. If it is hit on a hard object or dropped, breakage may occur. Be careful when handling a light source lamp.
A Phillips screwdriver is necessary when replacing the lamp unit. Hold the screwdriver firmly.
Grip the handle when you remove the lamp unit. Some parts of the lamp unit are sharpened and may cause injury.
The lamp may be broken. Hold the lamp unit horizontally and exercise care during lamp replace-ment to prevent scattering of glass fragments should the lamp break. If the projector is installed on the ceiling, do not carry out any replacement procedure directly underneath the lamp unit and keep your face away from the unit.
The lamp contains mercury. Contact the local government office or distributor for the correct dis-posal of the old lamp unit.
If you continue to use a lamp after the replacement time, the lamp may break.
Do not disassemble the lamp unit.
Note
Dispose of the packaging materials properly after unpacking the product.

NOTICE
For USA only Hg-LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws, See: www.lamorecycle.orq or 1-888-411-1996

Replacing the lamp unit

If the projector is operating, turn off the power by the following procedure and wait for the lamp unit to cool down before carrying out replacement.
1. Press the Power button twice to turn the projector off. (The power indicator lamp will illuminate orange.)
2. Wait until the power monitor on the projector turns red or starts flashing.
3. Turn off the MAIN POWER switch and disconnect the power cord plug from the wall outlet.

Replacement procedure

Make sure that components in the vicinity of the lamp unit are cool.
Use a Phillips screwdriver to turn the lamp cover fixing screws (lamp unit compartment fixing screw) (x2) on the projector rear panel until the screws turn freely and remove the lamp cover (lamp unit compartment).
- Remove the lamp cover by gently pulling it in the direction of the arrow in the figure.
- The location of the screws may differ with projector model. Check the operating instructions supplied with the projector for information on screw location.
Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely, and then hold the handles of the lamp unit and gently remove the lamp unit from the projector.
Insert the new lamp unit while making sure that the direction is correct, and then use a Phillips screwdriver to securely tighten the two lamp unit fixing screws. When inserting the new lamp unit, be particularly sure to push it in at point ®.
Insert the lamp cover (lamp unit compart-ment) and then use a Phillips screwdriver to securely tighten the two lamp unit fix-ing screws (lamp unit compartment fixing screws).
- Install the lamp cover by gently pushing it in the di-rection of the arrow in the figure.

Notes

Be sure to properly install the lamp unit and the lamp cover (lamp unit compartment).
If the lamp unit gets stuck during installation, remove it and try again. Never use force as you risk damaging the connectors.

Note

When the lamp unit is replaced, total lamp runtime will automatically be reset to 0.

Disposal of Old Equipment Only for European Union and countries with recycling systems

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local authority.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

EEE Complies with Directive of Turkey

Documents / Resources

| Panasonic ET-LAF100A Replacement Lamp Unit [pdf] Instruction Manual
ET-LAF100A Replacement Lamp Unit, ET-LAF100A, Replacement Lamp Unit, Lamp Unit
---|---