LOVMOR V3021DL-E Vanity Base Cabinet Instruction Manual
- May 15, 2024
- LOVMOR
Table of Contents
LOVMOR V3021DL-E Vanity Base Cabinet
PARTS DESCRIPTION
| PART | DESCRIPTION |
|---|---|
| A1 | Box side panel – left |
| A2 | Box side panel – right |
| B | Box bottom panel |
| C | Box back panel |
| D | Face frame |
| E | Toe kick panel |
| F1 | Drawer face panel |
| F2 | Drawer face panel |
| G1 | Drawer side panel – left |
| G2 | Drawer side panel – right |
| H | Drawer bottom panel |
| I | Drawer back panel |
| J | Door panel |
CAUTION
- Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them.
- The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly.
- Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended.
- Do not tighten all the screws until all the adjacent parts have been properly connected. Please do not throw away extra screws. Please refer to the actual product for the screw hole position.
HARDWARE CONTENTS
AA Glide and runner profile x 6
Included:
5/8” Flat Head Phillips Screw x 30
BB Adjustable drawer clips x 6
Included:
5/8” Flat Head Phillips Screw x 12
3/8” Flat Head Phillips Screw x 12
CC Soft – close hinge x 2
Be careful the length of the screws.
Included:
1/2” Flat Head Phillips Screw x 4
3/4” Round Head Phillips Screw x 2
**DD Wood corner block x 4
**
Included:
1” Flat Head Phillips Screw x 8
**EE Corner brace x 13
**
Included:
1/2” Round Head Phillips Screw x 52
**GG 1” Flat head Phillips screw x 4
**
**HH Rubber bumper x 14
**
TOOLS REQUIRED (NOT INCLUDED)
INSTALLATION OVERVIEW
Use 1/2” round head Philips screw x 10
Use 1/2” round head Philips screw x 10
Use 1/2” round head Philips screw x 2
Use 1/2” round head Philips screw x 2
Use 1/2” round head Philips screw x 8
Use 1/2” round head Philips screw x 20
Use 1/2” flat head Philips screw x 12
Use 5/8” flat head Philips screw x 12
Use 5/8” flat head Philips screw x 4 Be careful of the screw type.
Use 3/8” flat head Philips screw x 4 Be careful of the screw type.
Insert the drawer on the extended runner. To secure the drawer clips with
the runner, push the drawer in. Upon successful locking, a click can be heard.
Ensure that the hook on each runner profile fits into the corresponding holes
on the drawer back panel.
To level the drawer, use the green spur gears 1 to adjust drawer left and
right, the green spur gears 2 to adjust drawer up and down, and the green spur
gears 3 to adjust drawer inside and outside.
To take the drawer out, push the green clips at the same time to unlock drawer
clips.
Use 1/2” flat head Philips screw x 4
Use 3/4” flat head Philips screw x 2
If the door is not level when it is installed, the customer will need to turn
the screw clockwise to extend the hinge or counterclockwise to shorten the
hinge.
Some products may have hinges pre-installed.
To reverse the door, unscrew the 3/4″ round head phillips screws from each
hinge and remove the door panel. Then, reverse the door panel and drill the
3/4” round head phillips screws to each hinge through the pre-drilled holes to
tighten the hinges with cabinet face frame.
1” Flat Head Phillips Screw x 8 (2 screws for 1 corner block)
CUSTOMER SUPPORT
Dear customers,
Thank you for purchasing our product. If you require assistance, please contact the customer service team at the retailer where you purchased the product. The customer service team will be happy to assist you.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>