LOVMOR W0936-E Shaker Dove Wall Cabinet Instruction Manual

LOVMOR W0936-E Shaker Dove Wall Cabinet

Product Information

Specifications

• Model: W0936-E, W1236-E, W1536-E, W1836-E, W2136-E
• Box Side Panel – Left: A1
• Box Side Panel – Right: A2
• Box Bottom Panel: B
• Box Back Panel: C
• Face Frame: D
• Door Panel: J
• Adjustable Shelf: K
• Box Top Panel: L

Product Usage Instructions

Assembly Precautions
Before assembling the product, please take note of the following precautions

• Ensure all parts are carefully removed from the carton and check for any damages.
• Keep the hardware away from children during unpacking and assembly.
• Assembly is recommended to be done by two adults.
• Follow the instructions in the manual carefully and strictly to ensure proper assembly and operation.
• Do not tighten all the screws until all adjacent parts have been properly connected.
• Do not throw away extra screws. Refer to the actual product for screw hole positions.

Hardware Contents

• Soft-close hinge (CC) x 2
• 1/2 Flat Head Phillips Screw x 4
• 3/4 Round Head Phillips Screw x 2
• Corner brace (EE) x 12
• 1/2 Round Head Phillips Screw x 48
• Adjustable shelf clip (FF) x 8
• 1 Flat head Phillips screw (GG) x 4
• Rubber bumper (HH) x 2

Tools Required (Not Included)
The following tools are required for installation

• 1/2 round head Phillips screwdriver
• Drill

Installation Overview
The following steps provide an overview of the installation process

1. Attach A1 box side panel to A2 box side panel using 1/2 round head Phillips screws x 8.
2. Attach A2 box side panel to C box back panel using 1/2 round head Phillips screws x 8.
3. Attach C box back panel to A2 and A1 box side panels.
4. Attach L box top panel to A2 and A1 box side panels using 1/2 round head Phillips screws x 10.
5. Attach C box bottom panel to A2 and A1 box side panels using 1/2 round head Phillips screws x 10.
6. Attach D face frame to A1 and A2 box side panels using 1 Flat head Phillips screw x 4.
7. Attach K adjustable shelf to C box bottom panel using 1/2 round head Phillips screws x 8.
8. Attach J door panel to D face frame using 1/2 flat head Phillips screws x 4.
9. Install CC soft-close hinges to A2 box side panel and D face frame.
10. Attach HH rubber bumpers to the door panel.

FAQ

What should I do if the door is not level when installed?
If the door is not level when installed, you can adjust the hinges. Turn the screw clockwise to extend the hinge or  counterclockwise to shorten the hinge.

How do I reverse the door?
To reverse the door, follow these steps:

1. Unscrew the 3/4 round head Phillips screws from each hinge and remove the door panel.
2. Reverse the door panel.
3. Drill the 3/4 round head Phillips screws through the pre-drilled holes in the door panel to tighten the hinges with the cabinet face frame.

Where can I get customer service assistance?
If you require assistance, please contact the customer service team at the retailer where you purchased the product. They will be happy to assist you.

Wall Cabinet Instruction Manual

MODEL: W0936-E W1236-E W1536-E W1836-E W2136-E

CAUTION

Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them.
The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly.
Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended.
Do not tighten all the screws until all the adjacent parts have been properly connected. Please do not throw away extra screws.Please refer to the actual product for the screw hole position.

HARDWARE CONTENTS

TOOLS REQUIRED (NOT INCLUDED)

INSTALLATION OVERVIEW

Dear customers,
Thank you for purchasing our product. If you require assistance, please contact the customer service team at the retailer where you purchased the product. The customer service team will be happy to assist you.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>