Ibstock P8T5 Profile Tile Vented Ridge Pack Installation Guide
- May 15, 2024
- Ibstock
Table of Contents
WE ARE
Roofing and more.
INSTALLATION GUIDE – RIDGE DETAILING
Profile Tile Vented Ridge Pack 6m
Providing 5000mm²/linear metre Free Vent Area
Conforms to the requirements of BS:8612
- Install felt spacers if using V2 or Centurion/Senator packs (Picture 1). Lay underlay in accordance with BS 5534. Before fixing the top tiling batten, fix a ridge batten bracket to the top of each truss using 25mm aluminium nails on either side (Picture 2). The brackets should be fixed such that 20mm penetration into the ridge batten is acheivable when fixing theridge tiles. Fix the top tiling batte
- Locate a 25x50mm ridge batten into the ridge batten brackets and fix using 20mm nails on either side. Additional ridge battens should be spliced diagonally over a ridge batten bracket (Picture 3).
- Lay roof tiles in accordance with BS 5534.
- Snap together 3 top fillers to form a track for either side of the ridge. Locate a nailhole block end ridge tile into the tracks centrally over the ridge line. The top fillers must be positioned with the smaller ventilation voids on the outside of the ridge tile (Picture 4).
- Place a ridge seal under the block end ridge and locate into the channels of the top fillers (Picture 5).
- Secure the block end ridge using 2 x 80mm drive screws with washers and grommets.
- Continue fixing nailhole ridge tiles, top fillers and ridge seals along the ridge. If cutting is necessary to maintain the aesthetics of the ridge line, the block end ridge must not be cut. Ridge tiles must not be cut to less than half of their original length. All ridge tiles must be twice fixed with drive screws supplied (re-drill nailholes if necessary). At the verge, trim the last top fillers and fix the block end ridge tile as described in step 6 to finish the ridge line (Picture 6).
PAN8 Vented Ridge Pack (6m) (P8T5)
A) 10 no. Ridge Batten Brackets
B) 40 no. 25mm Aluminium Nails
C) 34 no. Top Filler PAN8
D) 26 no. 80mm Drive Screw (1 x Washer, 1 Grommet)
E) 13 no. Ridge Seals
Colours available: Grey, Rustic.
V2 Vented Ridge Pack (3m) (V2T5)
A) 6 no. Ridge Batten Brackets
B) 24 no. 25mm Aluminium Nails
C) 30 no. Top Filler V2
D) 14 no. 80mm Drive Screw (1 x Washer, 1 Grommet)
E) 7 no. Ridge Seals
F) 6 no. Duo-pitch Felt Spacers
Colours available: Grey, Rustic.
Centurion/Senator Vented Ridge Pack (3m) (CST5)
A) 6 no. Ridge Batten Brackets
B) 24 no. 25mm Aluminium Nails
C) 30 no. Top Filler Centurion/Senator
D) 14 no. 80mm Drive Screw (1 x Washer, 1 Grommet)
E) 7 no. Ridge Seals
F) 6 no. Duo-pitch Felt Spacers
Colours available: Grey, Rustic.
Conforms to the requirements of BS:8612
Plastic Type: Polypropylene
For further help and advice contact Technical on 01525 244900 or email Roofing.Technical@Ibstock.co.uk
IG4662A
WE ARE Ibstock.
Documents / Resources
|
Ibstock P8T5 Profile Tile Vented Ridge
Pack
[pdf] Installation Guide
P8T5, V2T5, P8T5 Profile Tile Vented Ridge Pack, Profile Tile Vented Ridge
Pack, Tile Vented Ridge Pack, Vented Ridge Pack, Ridge Pack, Pack
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>