VEVOR 5GL Insulated Beverage Dispenser Instruction Manual
- May 15, 2024
- VEVOR
Table of Contents
VEVOR 5GL Insulated Beverage Dispenser Instruction Manual
SAFETY INSTRUCTIONS
Read and understand this entire manual before operating and servicing this
product. Failure to follow these warning sand instructions can cause death,
personal injury or damage to valuable property.
Tip Over Hazard
- A child or adult can tip the insulated beverage dispenser and be killed or seriously injured.
- Serious injury may occur to children and adults if not secured before installation.
- This product is not a toy. Children should not play with or around insulated beverage dispenser at any time.
- Use as intended only.
- Do not stand on the product.
- Do not exceed the listed weight capacity
SAVE THESE INSTRUCTIONS
PROPER USE OF YOUR INSULATEDPRODUCT
- Wash and rinse the unit prior to its use.
- Preheating interior with hot water will improve heat retention.
- Pre-chilling entire unit will improve cold retention.
- Load container to its maximum capacity. Make sure thegasketisin place. Replace lid and lock in position.
CARE AND CLEANING OF INSULATED CARRIER
- Clean after every use. Destaining compounds approved for food or beverage contact may be used. Ask your detergent supplier for propercompound.
- Make sure gasket is removed prior to running through dishwasher. Also, prevent latches from getting caught in the conveyor.
BEVERAGE DISPENSER FILLINGINSTRUCTIONS
CAUTION: Liquid can overflow or squirt out of the vent cap
whensecuringlid if the unit is overfilled.
TO PREVENT OVERFLOW, DO NOT FILL HIGHERTHAN11/4”FROMTOP.
CARE AND CLEANING OF THEFAUCET
To remove faucet assembly from unit:
- Unscrew union nut to remove faucet from unit.
- Unscrew bonnet from faucet body to expose rubber seat cupandstemend. Pull down on seat cup to remove.
- Push back union nut and remove metal “c” ring. Unscrew Wing Nut To Remove spout from unit completely. Set aside large rubber washer, small rubber washer and “c” ring.
- Depress faucet lever in “locked open” position to clean top of bonnet thoroughly.
- Clean all parts of faucet with a solution of hot water andurncleaner.Usea faucet brush to clean the insides of the faucet and spout.
To return faucet assembly to unit:
- Place small rubber washer on spout first. Then place spout inside unit.
- Place large rubber washer on spout from outside the unit.
- Screw wing nut on spout with circle base facing the unit. Fit uniontown spout with inner screw side facing out. Replace metal “c” ring.
- Replace rubber seat cut on spring and stemend of faucet. Applypressure to secure seat cup.
- Screw bonnet onto faucet body.
- Screw faucet onto spout and tighten union nut.
EXPLODED PARTS DIAGRAM
Beverage Dispenser Faucet
| Number | Part Name |
|---|---|
| 1 | Faucet Lever |
| 2 | Bonnet |
| 3 | Stem End |
| 4 | Spring |
| 5 | Rubber Seat Cup |
| 6 | Faucet Body |
| 7 | Union Nut |
| 8 | Wing Nut |
| 9 | Large Rubber Washer |
| 10 | Small Rubber Washer |
| 11 | Metal C Ring |
| 12 | Spout |
Address : Baoshanqu Shuangcheng 803long 11hao 1602A-1609shi Shanghai
Imported to USA: Sanven Technology Ltd., Suite 250, 9166AnaheimPlace,
Rancho Cucamonga, CA 91730
Made In China
Technical Support and E-Warranty Certificate
www.vevor.com/support
We continue to be committed to provide you tools with competitive price. “Save
Half”, “Half Price” or any other similar expressions used by us only
representsanestimate of savings you might benefit from buying certain tools
with us compared to the major top brands and does not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
NEED HELP? CONTACT US! Have product questions? Need technical support?
Please feel freetocontact us:
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation four user
manual. The appearance of the product shall be subject totheproduct you
received. Please forgive us that we won’t informyouagainifthere are any
technology or software updates on our product.
