Farmhouse A02994 Chandeliers Rustic Round Wagon Wheel 8 Light Fixture User Manual

Farmhouse A02994 Chandeliers Rustic Round Wagon Wheel 8 Light Fixture

Specifications:

• Parts Included: Hex nut, Nipple, Single bar, Green ground screw, Canopy, Collar ring, Collar loop, Quick link, Chain, Loop, Metal box, Fixture loop, Arm, Socket, Fixture
• Accessories Included : Mounting screw, Plastic wire connector

Product Usage Instructions

Assembly & Installation:

1. Remove the fixture from the carton and ensure all parts and accessories are present.
2. Assemble the parts according to the instructions provided:
3. Thread the single bar onto the nipple and secure with a hex nut.
4. Thread the collar loop onto the nipple with the single bar facing down.
5. Determine the correct number of chain links needed for hanging height and connect the arms and loops using quick links.
6. Lace the wires through the chain and stop just before reaching the top.

Power Off:

1. Turn off electricity at the main fuse or circuit breaker box.
2. Place the wall switch in the OFF position.

Installation:

1. Attach the single bar to the outlet box with mounting screws.
2. Raise the canopy through the collar loop and position it securely against the ceiling.

FAQ:

1. Q: Can I install the fixture without shutting off the electricity?
   A: No, it is crucial to turn off the power before starting any installation work to prevent electric shock or injury.

2. Q: How do I adjust the collar loop for secure hanging?
   A: Unscrew threaded ring from screw collar loop, adjust collar loop on the single bar assembly by screwing in or out until secure hanging is achieved.

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1.  We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any  electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (A) Hex nut (1)
• (C) Nipple (1)
• (E) Single bar (1)
• (F) Green ground screw (1)
• (G) Canopy (1)
• (H) Collar ring (1)
• (I) Collar loop (1)
• (J) Quick link (10)
• (K) Chain (1)
• (L) Loop (1)
• (M) Metal box (1)
• (N) Fixture loop (8)
• (O) Arm (4)
• (P) Socket (8)
• (Q) Fixture (1)

ACCESSORIES & QTY ENCLOSED

• (B) Mounting screw (2)
• (D)Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1.  Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
2. Make assembly If the group of parts are not already assembled:

• Step A1 : Thread the single bar(E) onto nipple (C),
• Step A2 :Thread the hex nut (A)onto the nipple (C) till snug, At this point need note that: the side of single bar marked “GND”  must face to the down.
• Step A3: Thread the collar loop (I) onto the nipple (C) 3. Make pre-installation
• Step B1 : By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
• Step B2: Thread the loop (L)onto the threaded nipple onto the metal box (M)
  • Open the quick links to connect the arms (O)and the loops (N) on the metal box(M),then close the quick links
  • Open the quick links to connect the arms (O)and the loops (N) on the fixture(Q),then close the quick links
• Step B3: Attach the quick link(J)to connect the chain(K) and the loop(L) on the trim(M)
• Step B4: Carefully lace the wires through the chain (K)(every other link)and stop just before you reach the top of chain (K). Gently pull the wires till snug .

Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position
Make installation

1. Step C1: .Attach the single bar (E) to outlet box with mounting screws (B). The side of single bar marked “GND” must face out

2. Step C2: Raise the canopy (G) through screw collar loop (I) and screw the collar loop (I) to a proper position by measuring.
   Unscrew threaded ring (H) from screw collar loop (I) and remove the canopy (G). In this way, you would know the Proper position on which collar loop it should be located.

   • Note: The canopy (G) should be snug against the ceiling and the collar loop (I) should be screwed enough threads (no less than 6 threads )over the threaded nipple (C) for more secure hanging .If not, adjust the collar loop (H)on the single bar assembly by screwing the collar loop (I) in or out of the single bar (E) until the length is achieved.

3. Step C3: Slip the threaded ring(H) over the chain(K),then do the same with the canopy(G)

4. Step C4: Open the quick link(J)，attach the quick link (J) to connect the loop (I). Close the quick link(J)
   Pass the wires through screw collar loop(H) to the top of nipple(E) and gently pull till snug.

5. Step C5: If needed, cut off the wires length of fixture. At this point, the remaining wire length measured from the top of single bar(B) is at least 6″.

6. Step C6: Make wire connections Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE ,NEVER CONNECT
   WIRES TO GROUND WIRES

• Twist plastic wire connector(D) until wires are tightly joined together, wrap each connector with approved electrical tape for more secure connection, then carefully stuff all wires into the outlet box
• Step C7: Raise canopy (G) to ceiling and secure canopy (G) in place by tightening threaded ring (H) onto collar loop (I) Step C8: Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)
• Check everything is already installed properly, then you could turn on the light. Enjoy !

CLEANING
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>