saro JUSTIN Hand Wash Basin with Knee Control Instruction Manual
- June 15, 2024
- saro
Table of Contents
saro JUSTIN Hand Wash Basin with Knee Control
Product Information
Hand Wash Basin with Knee Control
Model: JUSTIN
Order No.: 353-1007
Specifications
- Dimensions: [insert dimensions]
- Material: [insert material]
- Color: [insert color]
- Knee Control Type: [insert type]
- Water Inlet Pipe Diameter: [insert diameter]
- Wastewater Pipe Diameter: 32mm
Product Usage Instructions
Assembly of the Hand Wash Basin
- Installing the Tap:
- Unscrew the plastic nut from the base of the top.
- Place the thread of the top through the hole located in the right corner of the sink bowl.
- Reattach the plastic nut to the thread of the top on the underside of the sink to secure the top in place.
- Flexible Hose:
- Screw one end of the flexible hose to the thread of the top on the underside of the sink.
- Note: There are two spare washers supplied.
- Push Button Installation:
- Lift knee flop on the sink to reveal a metal panel with a hole in the center.
- Unscrew the nut from the push button unit and place thread 1 through the hole, ensuring the button faces the front.
- Secure the push button unit in position by reattaching the nut to thread 1.
- When tightening the golden nut, make sure that thread 2 is pointing down.
- Flexible Hose:
- Take the free end of the flexible hose and attach it to thread 2 on the push button unit.
- Mixer Valve:
- Attach the mixer valve to thread 1 of the push button unit.
- Plug Unit:
- Unscrew the central bolt that holds the plastic waste pipe and the metal drain together.
- Place the metal drain inside the plug hole in the sink basin.
- Attach the plastic waste pipe to the underside of the basin using the long bolt, ensuring that the block rubber seal is positioned between the basin and the plastic waste pipe.
- Trap:
- Attach the trap to the plastic waste pipe, ensuring that it is in a vertical position.
- Fixing to the Wall:
- Fix the wall bracket to the wall using the screws provided.
- Hang the sink unit on the wall bracket using the lip on the reverse of the splashback.
- Secure the base of the sink to the wall using two additional screws.
- Run a silicon seal between the splashback and the wall.
- Connecting Pipes:
- Connect the hot/cold water inlet pipes to the mixer valve using a female 15/21 connector.
- Attach the wastewater pipe (32mm diameter) to the waste unit.
- Attention: An incorrect connection will lead to the destruction of the valve!
Frequently Asked Questions (FAQ)
Q: What should I do if the tap is leaking?
- A: If the tap is leaking, check if the plastic nut is securely attached to the thread of the top on the underside of the sink.
- Ensure that the washers are properly installed. If the issue persists, contact our customer support at info@saro.de.
Q: How do I clean the hand wash basin?
- A: To clean the hand wash basin, use a mild soap or detergent and a soft cloth or sponge. Avoid using abrasive cleaners or scrub brushes that may scratch the surface. Rinse thoroughly with water and dry with a clean towel.
Q: Can I use this hand wash basin for commercial purposes?
- A: Yes, this hand wash basin is suitable for both residential and commercial use.
General Information
- Read these installation instructions carefully as they contain important information for the installation of the hand wash basin.
- Should you pass the hand wash basin to a third party, these installation instructions should be handed over.
- As soon as you have unpacked the hand wash basin, check, whether everything is in a faultless condition. Should anything be damaged, inform your dealer.
- Dispose of the packing material according to the local regulations. All the packaging items (plastic bags, cardboard, polystyrene foam, nails, etc..) should not be left within reach of children, because they are potential sources of danger.
- The manufacturer/dealer cannot be made responsible for damages, which arise through not observing these installation instructions.
Installation
- The installation should be only done by a qualified specialist according to valid standards.
- Remove all protection and packing materials.
- Check the hand wash basin for any damages. If something is damaged, inform your dealer.
Assembly of the hand wash basin
- installing tap
- Unscrew the plastic nut from the base of the top, and place the thread of the top through the hole located in the right corner of the sink bowl.
- Reattach the plastic nut to the thread of the top on the underside of the sink securing the top in place (fig 1).
- Flexible hose
- Screw one end of the flexible hose to the thread of the top on the underside of the sink.
- Note: there are two spare washers supplied (fig 1).
- Push Button installation.
- Lift the knee flop on the sink to reveal a metal panel with a hole to the center, unscrew the nut from the push button unit, and place thread 1 through the hole, making sure the button faces the front.
- Secure this in position by reattaching the nut to thread 1. When tightening the golden nut make sure that thread 2 is pointing down (fig 2).
- Flexible hose
- Take the free end of the flexible hose and attach it to thread 2 on the push button unit (fig 2).
- Mixer valve
- Attach the mixer valve to thread 1 of the push button unit (fig 2).
- Plug unit
- To install the plug unit unscrew the central bolt that holds the plastic waste pipe and the metal drain together. Then place the metal drain inside the plug hole in the sink basin. Attach the plastic waste pipe to the underside of the basin using the lang bolt ensuring that the block rubber seal is positioned between the basin and the plastic waste pipe.
- Trap
- Attach the trap to the plastic waste pipe ensuring that it is in a vertical position.
- Fixing to the wall
- Fix the wall bracket to the wall using the screws provided. Hang the sink unit on the wall bracket using the lip on the reverse of the splashback, it should simply slide on. Once hung use the two remaining screws to secure the base of the sink to the wall. Run a silicon seal between the splashback and the wall.
- Connecting pipes
- Connect the hot /cold water inlet pipes to the mixer valve (using a female 15/21 connector)(fig 2). Attach the wastewater pipe (32mm diameter) to the waste unit.
- ATTENTION: an incorrect connection inevitably leads to the destruction of the valve!
Cleaning
- For hygienic reasons, the hand wash basin should be cleaned daily.
- Clean everything with a damp cloth and some commercial cleaning detergent. Afterward, dry it carefully.
- You can clean the hand wash basin with a high-grade steel cleaner also.
- Clean regularly the siphon.
Technical and other data
- Material: Stainless steel AISI 304
- Mixing valve
- With setback flap
- Splashback
- Connection to the waterpipe – ½“
- Siphon included
- Dimensions: W 400 x D 400 x H 240 mm
- Weight: net 5,2 kg – gross 5,8 kg
- info@saro.de
Documents / Resources
| saro
JUSTIN Hand Wash Basin with Knee
Control
[pdf] Instruction Manual
JUSTIN Hand Wash Basin with Knee Control, JUSTIN, Hand Wash Basin with Knee
Control, Basin with Knee Control, Knee Control, Control
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>