Modern Farmhouse 301GB Black Ceiling Fan without Lights User Guide

Classic Series

CEILING FAN

Faster Air

Higher Efficiency
Less Consumption

USE AND CARE GUIDE

READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION

Item 301GB

THANK YOU FOR PURCHASING

Thank you for purchasing this quality product. To ensure correct function and safety, please read and follow all instructions before assembly, installation and use of this ceiling fan.

SAFETY NOTICES

A WARNING/CAUTION notice denotes a hazard. It calls attention to installation procedure, operating procedure, maintenance procedure, or the like, that if not correctly performed or adhered to, could result in damage to this appliance, personal injury or death. No not proceed beyond a WARNING/CAUTION notice until the indicated conditions are fully understood and met.

SAFETY PRECAUTIONS

Please observe the following general safety precautions carefully before and during all phases of handling, installation, removal, operation and maintenance of this product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. We assume no liability for the customer’s failure to comply with these requirements.

SAFETY WARNING

1. Read all instructions and safety information. Review assembly diagrams provided before installing your new ceiling fan.
2. This fan must be installed by a licensed and qualified electrician.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
4. Young children should be supervised to ensure that they do not play with the appliance.
5. All electrical works must only be undertaken after disconnection of the power by removing fuses or turning off the circuit breaker, to ensure all pole isolation of the electrical supply.
6. Do not use it outdoors where it could be exposed to water or moisture.
7. This manual is not intended to instructor assist untrained or unqualified persons to install this ceiling fan.
8. It is the responsibility of a qualified, licensed installer and user to apply common sense and care at all times during installation and operation.
9. Fan, light kit and mounting plate must be earthed.
10. Use of an unapproved remote control voids the warranty. Only use our remote control.
11. Make sure electricity is turned off at the main power box before commencing work. Turn off the power by removing fuse or turning off circuit breaker before installing the fan and replacing led light.
12. Do not use sad state controllers.

PARTS LIST

Open the original carton and verify the following items. If there are any missing or damaged items, contact customer service. On not throw away the carton or other packaging material as it may be needed for warranty replacement or repair.

        *A3**

B             C

D           E

F                 G

  *H3                       M **

*I7     ** J ****

*K4           *L4 ****

N   **O **

P                     Q ****

R     S           T ****

A     Blade x 3
B     Canopy x 1
C     Mounting Bracket x 1
D     Coupling Cover x 1
E     Blade Holder x 1
F     Motor Assembly x 1
G     Bottom Cover x 1
H     Downrod x 3
I       Blade Mounting Screw x 7
J       Inner Hexagon Spanner x 1
K     Wood Screw x 4
L      Wire Connector x 4
M     Motor Wire Terminal x 1
N     Balance Kit x 1
O     8#,10# Screw Set x 2
P     Remote x 1
Q    Wan Plug & Screw x 2
R     Wait Control x 1
S     Supply Wire Terminal x 1
T     Receiver x 1

FAN INSTALLATION INSTRUCTIONS

WARNING
Risk of electric shock

WARNING

In order to prevent fire and electric shock accidents, it is forbidden to install and use electrical accessories not equipped with this product! Please cut off the power before installation, disassembly, maintenance, or cleaning to avoid personal injury! If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.

1. INSTALL THE WALL CONTROL

NOTE
Please skip this step if you don’t need wall control.

NOTE
than indicated, have this unit installed by a qualified electrician.

a) Disconnect the power and remove the existing wall plate and switch.

b) Push the slide switch on the wall control down to the OFF position and connect wires correctly.

• Connect the Black (AC IN L) wire from wall control to Black (Hot) wire coming from the Household Supply.
• Connect the other Black (FOR LOAD L) wire from wall control to the Black wire going to the ceiling fan.
• Connect the White (Neutral) wire from Household Supply to the White (Neutral) wire going to the ceiling fan.
• Connect the Green (GROUND) wire from wall control to Ground (Green/Bare Copper) wire coming from the Household Supply.

c) Attach wall control unit to wall outlet box by using the two screws provided and attach wall plate to the switch control front by using the two screws provided.

WARNING

To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the well plate and the wall.
WARNING

Check to one that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until the blades are in place, or noise and fan damage could result.

1. Household Supply

2. BLACK(Hot)

3. WHITE(Neutral)

4. GROUND
   (Green /Bare Copper)

5. Outlet Box

6. GROUND
   (Green mom Receiver, Downrod a Bracket)

7. WHITE

8. GREEN

9. BLACK

10. Receiver

11. BLACK
    (FOR LOAD L)

12. GREEN
    (GROUND)

13. BLACK
    ( AC IN L)

Well Control Function

(1) LED Indicator
(2) Fan ON/OFF (Pairing Button)
(3) No Function
(4) Fan Forward/Reverse
(5) Fan Speed 1-6
(6) Power Supply OFF
(7) Power Supply ON

Kindly Reminders

1. The well control and receiver included with your fan have been paired beforehand. The learning code matching mode is only for when the well control and receiver lose control after installation or during use.
2. Learning code matching mode is used between wall control and receiver. Turn “ON” the supply power within 30 seconds and press the wall control ” ” for 5 seconds, it can load normally after hearing a long sound “bee” , which means learning successfully and it can work normally. (PS: Matching mode is not accepted after turning “ON” the supply power over 30 seconds)
3. When the well control cannot control the receiver, please check whether any existence of similar remote controlled products nearby, then check whether they work, because a remote-controlled product with the same frequency will disturb each other.
4. When installing the fan, the fan ceiling cover doesn’t press the antenna (or other wire), or it is easy to damage the wire and cause short-circuit or loss of control.

2. INSTALL THE MOUNTING BRACKET

The lowest point on the fan blade must be at least 2.1m (7ft) from the floor. Make sure that ceiling joists are strong enough and of adequate size to support the weight of the fan of about 18kg (40lb).

WOODEN CEILING

Secure mounting bracket to ceiling joist or suitable piece of timber inserted between the ceiling joists. The mounting bracket should be attached with four wood screws.

1. Support Structure
2. Ceiling Outlet Box (required)
3. Standard Mounting Style

CONCRETE CEILING

According to the length of expansion screws, bore holes by percussive drills with 8mm drill. After that, fix the mounting bracket on ceiling with expansion screws.

Use standard mounting or low-profile mounting to hang the fan from a fiat ceiling. Attach the mounting bracket to the electrical box.

1. Support Structure
2. Ceiling Outlet Box (required)
3. Angled Mounting Style
4. Maximum tilting angle 30°

For angled ceilings, point the mounting bracket opening toward the peak. Attach the mounting bracket to the electrical box.

If there isn’t an existing outlet box, then install one using the following instructions:

Disconnect the power by removing the fuses or turning off the circuit breakers.
Secure the outlet box (A) (not included) directly to the building structure.
Use appropriate fasteners and materials (not included).
The outlet box and its bracing must be able to fully support the weight of the moving fan (at Least 35 lbs).
Do not use a plastic outlet box.
Figures below show two different ways to mount the outlet box (not included).

NOTE
If you are installing the ceiling fan on A sloped ceiling, you may need a longer Downrod to maintain proper clearance Between the tip of the blade and the Ceiling.

NOTE
The ceiling fan must be installed in a location no that the blades are spaced 50cm (20inch) from the tip of the blade to the nearest objects or walls.

To hang your fan where there is an existing fixture but no ceiling joist, you may need to install a ceiling fan hanger bar / Saf-T-Bar / Saf-T-Brace (C).

3. INSTALL THE FAN BLADES

Install the fan blades by aligning the holes on the blade with the holes on the fan motor assembly net by the provided set screws and washers. Make sure the net screws securing the blade are tight and the blades are properly seated. Finally screw the bottom cover into the motor shaft.

4. INSTALL DOWNROD, CANOPY & COUPLING COVER

a) Select the right downrod according to the height of ceiling; This fan attaches 5 &10 & 24 inches downrod for your preference.

b) Take off the locking pin, hanger ball, bolt and two downrod screws from coupler.

c) Let the downrod across the canopy and coupling cover in right direction, then put the power cord through downrod.

d) Put the downrod into coupler; Insert the bolt, hanger ball and locking pin. Lock the downrod screw and cover the coupler with the upper cover.

5. FAN MOUNTING

a) Hang the fan motor assembly on the mounting bracket, and ensure the key slot of the hanger ball is positioned on the key pin of the mounting bracket.

b) Plug motor wire terminal, lamp wire terminal (if the fan has lamp) and the included supply terminal in the corresponding port on the remote receiver.

1. Motor Wire Terminal
2. Supply Wire Terminal
3. Remote Receiver

c) Connect wires correctly: Connect the Neutral (White or Blue) supply wire from the outlet box to the Neutral (White or Blue) fan wire; Connect the Hot (Black or Brown) supply wire from the outlet box to the Hot (Black or Brown) fan wire; Connect the Ground wire (Bare Copper or Green&Yeltow) from the outlet box to the fan Ground (Green or Green&Yellow) wire, mounting bracket Ground (Green or Green&Yellow) wire and downrod Ground (Green or Green&Yellow) wire. Screw each wire with a connector until wires are tightly joined together, and wrap each connector with approved electrical tape for more secure connection.

1. GROUND
   Bare Copper or Green&Yellow

2. GROUND
   Green or Green&Yellow

3. AC IN N NEUTRAL
   White or Blue

4. AC IN L HOT
   Black or Brown

5. NEUTRAL SUPPLY WIRE
   White or Blue

6. HOT SUPPLY WIRE
   Black or Brown

d) Slide the remote controller receiver unit into the mounting bracket as shown in the figure below.

1. Remote Receiver

e) Unscrew the two top canopy fixing screws halfway attached at the bottom of the mounting bracket. Slide the top canopy up the downrod onto the mounting bracket. Turn the canopy until fixing screws lock into position and then fasten the screws.

REMOTE CONTROL FUNCTION

(1) LED Indicator
(2) Fan ON/OFF (Pairing Button)
(3) Fan Speed Up
(4) Fan Speed Down
(5) Timer Control
(6) Natural Wind
(7) BATTERY: 12V/23A x 1
(8) Fan Forward/Reverse

Kindly Reminders

1. The remote and receiver included with your fan have been paired beforehand. The learning code matching mode is only for when the remote and receiver lose control after installation or during use.
2. When the remote cannot control the receiver, please check whether the battery switch touching normally or not, correction of the positive and negative, and full or empty of power.
3. When the remote cannot control the receiver, please check whether any existence of similar remote-controlled products nearby, then check whether they work, because remote-controlled product with the same frequency will disturb each other.
4. The low voltage of battery will affect the sensitivity of the remote and the signal reception accordingly. Replace the battery if it is getting low voltage (the indicated light will flash out when the battery gets low voltage).
5. Please take out the battery from the remote when left unused for a long time.
6. When installing the fan, the fan ceiling cover doesn’t press the antenna (or other wire), or it is easy to damage the wire and cause short-circuit or loss of control.
7. The motor does not react instantaneously to changes made by the handset. Be patient and allow the motor to process the instruction when changing functions.
8. The remote control includes a memory function. This function records the status when power has been disconnected to allow resumption when power is restored.

REPAIRING THE FAN’S RECEIVER WITH REMOTE

Should the remote and receiver lose control after installation or during use, the pairing of the remote and the receiver must be repaired. Below are the operating symptoms and methods to repair the pairing of the ceiling fan remote and receiver.

Issues:

Loss of control – Fan is only running at high speed after installation

Loss of control – No reverse function after installation

Loss of control – Remote cannot communicate with the receiver

a) Switch OFF the main power to the ceiling fan for 30 seconds.

b) Press and hold the Pairing Button on the remote until the beep sound heard within 30 seconds of switching the power ON to the receiver of the ceiling fan. If the fan has a light kit attached, the light will flash on and off to indicate the pairing process is activated. When a long beep sound is heard, the pairing is successful.

c) Turn ON and change the speed of the ceiling fan via the remote to check the operation and successful pairing.

When multiple fans are installed e.g. “Fan A” and “Fan B”, and each fan needs to be paired separately.

a) Switch OFF the main power to both “Fan A” and “Fan B” for 30 seconds.

b) Press and hold the Pairing Button on remote for 5 seconds within 30 seconds of switching the power ON to the receiver of “Fan A”. If the fan has light kit attached, the light will flash on and off to indicate the pairing process is activated. When a long beep sound is heard, the pairing is successful.

c) Turn OFF the main power to “Fan A” which is paired first; Press and hold the Pairing Button on another remote for 5 seconds within 30 seconds of switching the power ON to the receiver of “Fan B”. When a long beep sound is heard, the pairing is successful.

When multiple fans are installed e.g. “Fan A” and “Fan B”, and you want to use one remote to control both “Fan A” and “Fan B”.

Note that “Fan A” and “Fan B” should be located in one room within 10 meters/32 feet and there is no wall blocked between “Fan A” and “Fan B”.

a) Switch OFF the main power to both “Fan A” and “Fan B” for 30 seconds.

b) Press and hold the Pairing Button on one remote for 5 seconds within 30 seconds of switching the power ON to the receiver of both Tan A” and “Fan B”. If the fan has a light kit attached, the light will flash on and off to indicate the pairing process is activated. When a long beep sound is heard, the pairing is successful.

TROUBLESHOOTING GUIDE

1. Fan / Remote Is Not Working

Ensure the remote is within the 20-foot range of the receiver.

a) Check that mains circuit breakers are in the ON position.

b) Check that isolation wall switch is in the ON position.

c) Check that batteries in the remote handset (if any) are in good condition and oriented correctly.

d) Carry out and complete remote and receiver pairing process (refer to REPAIRING THE FAN’S RECEIVER & REMOTE above).

e) Check that live, neutral, ground and light (if any) wires from isolation wall switch, remote receiver (if any) through to fan are all wired correctly in accordance with wiring diagram.

f) Check that all wire connections at wall switch, wire connector and/or terminal block are secured (not loosened). If fan still does not work, please contact customer service.

2. Fan Sounds Noisy

a) Fully tighten light fitting (version with light).

b) Re tighten all screws on fan blades (do not over-tighten).

c) Re-tighten all screws in the hanging bracket and covering plate.

d) Allow 24-hour break-in period. Most noises associated with the new fan may disappear during this time.

3. Fan Turns But Does Not Move Much Air

a) The fan may be running in reverse (for fans with reverse running option).

b) The room may contain items that obstruct the airflow.

4. Fan Wobbles

a) Check that all blade brackets are tightened securely.

b) Inconsistent blade level: To check blade level, measure the distance from each blade tip to the ceiling. If measurements are inconsistent, adjustments of brackets will be required.

c) Deviations in distance from blade to blade: To check blade separation, measure the distance from blade tip to blade tip. Should measurements vary, loosen screws connecting blades and brackets (one at a time) then shift the blade to a proper position and re-tighten the screws.

HOW TO USE BALANCING KITS

For your convenience, a balancing kit is included. Please follow this procedure when balancing the fan:

1. Check that all blades and blade arm screws are secure.
2. Most fan wobbling problems result from blade levels being unequal. Check this level by selecting a point on the ceiling above one fan blade’ s tip. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be within 1/8″ (0.32cm).
3. Use the enclosed blade balancing kit if the blade wobbling is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smooth operation.

IMPORTANT FACTS

Warm Note

All electric motors, including fan motors make some noise and may feel hot to touch, this is not a fault. Ceiling fans tend to move during operation as they are not generally rigid-mounted. Movement of a couple of centimeters is quite normal and doesn’t suggest the fan will fall down. Rigidly mounted ceiling fans generate excessive vibration and stress on their mountings. Fan lights will rattle if they are not supplied with the fan. And this is not covered by warranty.

Fan Operation

A ceiling fan is an environmentally smart choice when it comes to cooling as well as helping to warm your room. You should see a reduction in both cooling and heating costs by regular use of your fans. Do not hesitate to use your fans in both summer and winter months. In summer, fan should be set to spin in anti-clockwise direction blowing down coot breeze. In winter, fan should be set to spin in clockwise direction so that an upward airflow will push warm air off the ceiling and circulate it downwards into the living areas. In winter months use the fan at a lower speed than in summer.

Normal Wear And Tear

Threaded components working slightly loose, or blade carriers becoming slightly bent due to vigorous cleaning or bumping can cause extra wobble and noise. This is not covered under warranty, but a little care and maintenance can reduce or prevent this problem.

Night Noises

This is the biggest cause of service calls, which are outside the manufacturer’s warranty. If a fan has a fault it will be noticeable at all times. Naturally when everything is quiet at night you will be more inclined to hear small noises, which may not be noticeable at other times. Even slight signals superimposed in your electricity supply for off -peak hot water control may cause a change in the fan motor noise. This is normal.

Customer Service

Check that all parts are available before beginning assembly.
Do not attempt to assemble the product if any parts are missing or broken. If you encounter any problems before and during the installation, please feel free to contact us.

Technical Support:
support@yaobo-global.com

Business Cooperation:
business@yaobo-global.com

YaoBo-Global
WhatsApp

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>