SENAO PCE2311M WiFi 6 ax3000 2×2 Dual Concurrent mPCIe Module User Manual
- June 17, 2024
- Senao
Table of Contents
SENAO PCE2311M WiFi 6 ax3000 2×2 Dual Concurrent mPCIe Module
Product Information
Specifications
-
Product Name: WiFi 6 ax3000 2×2 dual concurrent mPCIe Module
-
Model Name: PCE2311M
-
FCC ID: U2M-PCE2311M
-
Hardware Design Specification:
- PCE2311M is a WiFi 6 dual concurrent mPCIe module supporting 2.4GHz HE40 and 5GHz HE160 interfaces.
- Backward compatible with 802.11a/b/g/n/ac standards.
- Equipped with MTK chipset for high-performance WiFi 6 traffic.
-
Power Consumption: Max 8W
-
PCB Dimensions/Layers: 50.95 x 30 x 1.0 mm / 4 layers
-
Support driver: Integrated module on
customer’s system board, SDK, or driver to be discussed. -
Compliant Regulatory:
- Tier 1 Compliant Regulations for USA and EU standards.
Product Usage Instructions
Installation
- Ensure the system is powered off before installing the PCE2311M module.
- Locate the mPCIe slot on your system board and insert the module carefully.
- Secure the module in place and power on your system.
Driver Installation
- Download the appropriate driver or SDK for the PCE2311M module from the manufacturer’s website.
- Install the driver following the provided instructions.
- Restart your system to complete the driver installation process.
Antenna Installation
- Ensure the antennas are connected to the designated ports on the PCE2311M module.
- Place the antennas at least 20 cm away from all persons for RF exposure compliance.
- Avoid co-locating antennas with other transmitters for optimal performance.
FAQ
-
Q: What should I do if I encounter connectivity issues with the PCE2311M module?
A: If you experience connectivity issues, try restarting your system and ensuring proper antenna placement. You can also check for driver updates or contact customer support for assistance. -
Q: Is the PCE2311M module compatible with older WiFi standards?
A: Yes, the PCE2311M module is backward compatible with ancient standards such as 802.11a/b/g/n/ac.
Product Name: WiFi 6 ax3000 2×2 dual concurrent mPCIe Module
Model Name: PCE2311M
FCC ID: U2M-PCE2311M
Hardware Design Specification
PCE2311M is a WiFi 6 dual concurrent mPCIe module to engine 2.4GHz HE40 and 5GHz HE160 interface to carry high-performance WiFi 6 traffic and be backward compatible with ancient 802.11a/b/g/n/ac standard. The advanced MTK chipset had been built in this module to operate service connections via Gateway and SASE appliances under a pervasive environment.
Major Components
WiFi Specification (2.4GHz/5GHz)
- Based on the transmit power (Tx) and receive sensitivity (Rx) specifications of MT7976DN, we conclude Tx power from chips and summarize Rx specification as the following table.
Power Consumption
- The max power consumption is around 8W.
- PCB Dimensions/Layers.
Support driver
- PCE2311M is an integrated module on the customer’s system board. The selected SDK or driver would be discussed and be negotiated firstly. According to initial validation from Seano, we successfully brought up this module on the MTK7622 platform.
Compliant Regulatory
The planned certification domain would be covered following regulations.
Tier 1 Compliant Regulatory
Warning statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, under part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used per the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
- Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
- This module is intended for OEM integrators. The OEM integrator is responsible for compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.
RF Exposure warning
This equipment must be installed and operated per provided instructions and
the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure
compliance.
USERS MANUAL OF THE END PRODUCT
- In the user’s manual of the end product, the end-user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated.
- The end-user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
- The end-user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT
- The final end product must be labeled in a visible area with the following ” Contains FCC ID: U2M-PCE2311M “.
- This radio transmitter FCC ID: U2M-PCE2311M has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Antenna List Note: The antenna connector is SMA Male type.