Nathan James 12201 Leigh Pendant Lighting User Manual
- June 17, 2024
- NATHAN JAMES
Table of Contents
Nathan James 12201 Leigh Pendant Lighting
Ok, let’s get rolling
- This should be easy, just follow our instructions and you will be back to Netflix in no time.
Estimated time for assembly
What you need
- Your favourite snack or energy bar (Save the bubbly for once your fixture is safely installed!)
- Use the packaging carton as a working surface to prevent product damage during assembly
- Phillips head screwdriver
Do not use a drill
What’s included
|
Description
|
Qty
---|---|---
A| Glass Shade| 1
B| Fixture| 1
C| Canopy| 1
D| Stem (6”)| 1
E| Stem (12”)| 1
F| Stem (12”)| 1
G| Finial Nut| 2
H| Shade Nut| 4
I| M425mm Mounting Screw| 2
J| Mounting Plate| 1
K| Wire Connector| 3
L| M1025mm Thread Insert| 1
Scan me! Free Lifetime Warranty
- Toll-free at 1-866-619-1004
- Help@nathanjames.com
- Nathanjames.com/help
Safety first, fun later
Safe use of this product starts with you.
- Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect the product upon receipt and each use.
- Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulting from failure to follow instructions or improper use of this product.
Do not modify the structure of this product in any way
- Our products have been tested to meet specific safety measures as they were originally intended to be sold.
- Any modifications will present the risk of creating significant safety issues which Nathan James will not be responsible for.
Proper use
- DO NOT use for commercial purposes
- DO NOT leave spilled liquid on the fixture
- DO NOT use light fixture if damaged
- DO NOT make temporary repairs
- DO NOT use outdoors
WARNING
Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004
WARNING: RISK OF ELECTRIC SHOCK
Before starting the installation, disconnect the power by turning off the
circuit breaker or by removing the appropriate fuse at the fuse box. Turning
the power off at the switch is NOT SUFFICIENT to prevent electrical shock.
PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
The goods
IMPORTANT
- Do not tighten bolts/screws completely until all bolts/screws are lined up and inserted into holes.
- Do not over-tighten screws and bolts to avoid stripping.
- Please use hand tools to assemble this product. Do not use power tools.
Pre-Installation
- Read all instructions before beginning assembly.
- To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
- Keep the receipt and these instructions for proof of purchase.
- Suggested Bulb: G19 Edison 60 Watt Equivalent | E26 Medium Base | Dimmable
- Fixture Max Wattage: 60W
- 120V 60Hz AC Only.
Step 1
- Let’s get this thing fired up! Or should we say, lit!
- Separate the Mounting Plate (J) from the Canopy (C) by removing the Finial Nuts (G).
Step 2
- Install a Mounting Plate (J) to your pre-installed electrical box using the M4*25mm Mounting Screws (I).
Note: Be sure that you are only making the connections to a 120V 60Hz AC circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
Step 3
Decide your necessary fixture stem length to achieve your desired fixture
height. Then, pass the cord through each of the necessary stem components for
your desired fixture height.
Step 4
- Thread the necessary stem components together to complete the connection between the Canopy (C) and the Fixture (B) (components will vary depending on your desired fixture height).
Step 5
- Wrap the Ground Wire from the Fixture (B) around the grounding screw on the Mounting Plate (J) & then secured by tightening the screw.
- Use a Wire Connector (K) to join the ground wire from the Fixture (B) with the ground wire from the Electrical Box.
Step 6
Use Wire Connectors (K) to join the remaining matching coloured wires (White to White, Black to Black). Once complete, tuck the excess wire into the electrical box.
Step 7
- Secure the Canopy (C) to the Mounting Plate (J) by threading the Finial Nuts (G) into place.
- To properly fasten the Finial Nuts (G), thread in or out to adjust for proper threading length.
Step 8
- Remove the Shade Set Screws (H) from the Fixture (B).
Step 9
- Carefully slide the Glass Shade (A) into the ring of the Fixture (B) and then use the Shade Nuts (H) to hold it in place.
Step 10
- And last but not least, we need to add the bulb! Insert the bulb of your choice (we recommend a Type G80 bulb) and let there be light!
Troubleshooting
| Problem | Possible Causes | Solutions |
|---|---|---|
| The bulb will not light. | The bulb is burned out. | Replace the light bulb. |
| The power is off. | Ensure the power supply is on. | |
| The circuit breaker is off. | Ensure the circuit breaker is in the ON position. | |
| The fuse blows or the circuit breaker blows when the light is turned on. | ||
| There is an exposed wire. | Discontinue the use of the light. |
Contact a qualified electrician or reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004.
Questions? Don’t worry, we’ve got the answers
- What other light bulbs can fit in this light?
- The bulb must not be greater than the maximum wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than the diameter of any area of shade so that it can fit.
- Can I use an LED light bulb?
- Yes, so long that the base size matches and the diameter of any area of the bulb is less than the diameter of any area of shade so that it can fit.
- Is this UL/ETL certified?
- Yes, all our products are either UL or ETL.
- Do I need an electrician to set up the hardware?
- We recommend using a certified electrician for all hardwiring, although all of our fixtures can be set up without an electrician, as long as you are replacing an existing fixture or have an existing junction box ready for a fixture installation. ENSURE POWER IS
- OFF WHEN INSTALLING. For all new constructions, please use a certified electrician.
- Can I retrofit this hard-wired to a plug-in or vice-versa?
- Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire fixture can become a plug-in fixture. For many products we will provide all the necessary hardware to make these changes, if not, you will need to purchase the necessary hardware.
- Is this light compatible outside
- North America?
- Our lighting is only warranted in Canada and the United States.
- What do I do if the product is not working?
- Try a different light bulb and confirm proper installation.
- Can these lights work on a dimmer?
- Disability is related to the light bulb and the wall switch, not the light fixture. All our hardware fixtures are compatible with dimmable light bulbs. We recommend using a dimmer switch, as it extends the life of the bulb and allows for energy saving and great ambience. If using an LED bulb, please ensure both your LED bulb and dimmer switch are compatible.
- Can I use the fixture outdoors?
- No, this product was designed to be used indoors only in dry locations.
No heartburn, when we handle the return
- Give us a call at 1-866-619-1004 or shoot us a message at help@nathanjames.com we will issue you a free replacement with zero hassle.
- We don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
We are only in business if you’re happy
For starters, thanks for being you.
- Toll-free at 1-866-619-1004
- Help@nathanjames.com
- NathanJames.com/help
We do our best to ensure your product arrives without any problems, but occasionally mistakes happen—as humans, we are imperfect beings. If a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.
Warranty
- This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q
Did we do alright? Please spread the love!
If you are happy with your product, tell your friends and family about us or
even better leave us a review online. Spreading the word allows us to make
more people happy and keep our prices low for your next purchase.
CONTACT
- Toll-free at 1-866-619-1004
- Help@nathanjames.com.
- NathanJames.com/help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>