VEVOR LL9450UP Insulated Beverage Dispenser User Manual
- June 17, 2024
- VEVOR
Table of Contents
VEVOR LL9450UP Insulated Beverage Dispenser
Product Information
Specifications
- Model: KF-40
- Product: Insulated Beverage Dispenser
- Manufacturer: VEVOR
- Website: www.vevor.com/support
FAQ
- Q: How do I prevent liquid overflow when filling the dispenser?
- A: Do not fill higher than 1/4 from the top to prevent overflow.
- Q: How should I clean the insulated carrier?
- A: Clean after every use using approved destaining compounds for food or beverage contact.
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
SAFETY INSTRUCTIONS
Read and understand this entire manual before operating and servicing this product. Failure to follow these warnings and instructions can cause death, personal injury or damage to valuable property.
Tip Over Hazard
- A child or adult can tip the insulated beverage dispener and be killed or seriously injured.
- Serious injury may occur to children and adults if not secured before installation.
- This product is not a toy. Children should not play with or around the insulated beverage dispener at any time.
- Use as intended only. Do not stand on the product.
- Do not exceed the listed weight capacity.
SAVE THESE INSTRUCTIONS
PROPER USE OF YOUR INSULATED PRODUCT
- Wash and rinse the unit prior to its use.
- Preheating interior with hot water will improve heat retention.
- Pre-chilling entire unit will improve cold retention.
- Load container to its maximum capacity. Make sure the gasket is in place. Replace lid and lock in position.
CARE AND CLEANING
CARE AND CLEANING OF INSULATED CARRIER
- Clean after every use. Destaining compounds approved for food or beverage contact may be used. Ask your detergent supplier for proper compound.
- Make sure gasket is removed prior to running through a dishwasher. Also, prevent latches from getting caught in the conveyor.
BEVERAGE DISPENSER FILLING INSTRUCTIONS
CAUTION
- Liquid can overflow or squirt out of the vent cap when securing lid if the unit is overfilled.
TO PREVENT OVERFLOW, DO NOT FILL HIGHER THAN 11/4” FROM TOP.
CARE AND CLEANING OF THE FAUCET
To remove faucet assembly from unit:
- Unscrew union nut to remove faucet from unit.
- Unscrew bonnet from faucet body to expose rubber seat cup and stem end. Pull down on seat cup to remove.
- Push back union nut and remove metal “c” ring. Unscrew wing nut to remove spout from unit completely. Set aside large rubber washer, small rubber washer and “c” ring.
- Depress faucet lever in “locked open” position to clean top of bonnet thoroughly.
- Clean all parts of faucet with a solution of hot water and urn cleaner. Use a faucet brush to clean the insides of the faucet and spout.
To return faucet assembly to unit:
- Place small rubber washer on spout first. Then place spout inside unit.
- Place large rubber washer on spout from outside the unit.
- Screw wing nut on spout with circle base facing the unit. Fit union nut on spout with inner screw side facing out. Replace metal “c” ring.
- Replace rubber seat cut on spring and stem end of faucet. Apply pressure to secure seat cup.
- Screw bonnet onto faucet body.
- Screw faucet onto spout and tighten union nut.
EXPLODED PARTS DIAGRAM
Beverage Dispenser Faucet
| Number | Part Name |
|---|---|
| 1 | Faucet Lever |
| 2 | Bonnet |
| 3 | Stem End |
| 4 | Spring |
| 5 | Rubber Seat Cup |
| 6 | Faucet Body |
| 7 | Union Nut |
| 8 | Wing Nut |
| 9 | Large Rubber Washer |
| 10 | Small Rubber Washer |
| 11 | Metal C Ring |
| 12 | Spout |
Contact
- Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
- Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
- Technical Support and E-Warranty Certificate: www.vevor.com/support
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
- Technical Support and E-Warranty Certificate
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>