Montigo DRLT36 Linear 36 Direct Vent Gas Fireplace Instruction Manual

Montigo DRLT36 Linear 36 Direct Vent Gas Fireplace

Product Specifications

• Models: DRLT36, DRLT36-2, DRLT48, DRLT48-2, DRLT60, DRLT60-2, DLT63, DLT63-2, DRSQT34, DRSQT34-2, DRSQT38, DRSQT38-2, DRSQT42, DRSQT42-2, DRSQT46, DRSQT46-2
• Product Type: Adjustable Trim Kit
• Mounting: Magnets to the inside edge of the lip

Product Usage Instructions

Installation

1. Ensure the facing material is fully finished before starting the installation of the trim kit.
2. Trim the bottom off the DelRay screen tabs before construction and installation of the trim kit.
3. Square off all 4 corners of the trim kit.
4. Orient the trim so that the notched section is at the bottom.
5. Slide the side pieces into the top and bottom tracks.
6. Slide the trim on the inside of the flush frame of the opening and push it in until it is flush with the facing material.
7. Use construction adhesive if needed to secure the trim in place.

Assembly

1. For DelRay Linear Screens manufactured before May 2020: Check the rating plate serial number for the date of manufacture. If unsure, measure the length of the tabs.
2. Square off all 4 corners of the trim kit.
3. Slide the side pieces into the top and bottom tracks.
4. Slide the trim on the inside of the flush frame of the opening and push it in until it is flush with the facing material.
5. The trim can slide in and out within the depth limits of the trim kit.

Notice

Installer: Leave this manual with the appliance. Consumer:
Retain this manual for future reference.

Warning

Some materials used in the manufacturing process of this product can expose you to Benzene which is known in the State of California to cause cancer and birth defects or other reproductive harm. For more information visit www.P65warnings.ca.gov

FAQ

Q: Can I use this trim kit on any type of facing material?

A: The facing material should be fully finished before installation. Ensure it falls within the depth limits of the trim kit for proper installation.

Q: How do I secure the top trim piece for Distinction Trims DLT72?

A: Secure the top of the trim to the finishing material with the included screw to prevent bowing when heated.

DRLT36, DRLT36-2, DRLT48, DRLT48-2, DRLT60, DRLT60-2, DLT63, DLT63-2, DRSQT34, DRSQT34-2, DRSQT38, DRSQT38-2, DRSQT42, DRSQT42-2, DRSQT46, DRSQT46-2

1” ADJUSTABLE TRIM KIT

• The installation of this KIT must be done by a qualified and certified gas appliance installer.
• Check local codes and read all instructions prior to installation.

Installation

Assembly

1. The facing material should be fully finished before installation of the trim kit.

THIS SECTION ONLY FOR DELRAY LINEAR SCREENS MANUFACTURED BEFORE MAY 2020
Please refer to your rating plate serial number for the date of manufacture. If unsure, measure the length of the tabs, if it is below ¼”, it does not need modification.

2. Before construction and installation of the trim kit can begin, the bottom ⅛” off the DelRay screen tabs must be trimmed.

3. Slide the side pieces into the top and bottom tracks.

4. Ensure the all 4 corners of the trim kit are squared off. Before installation orient the trim so the notched section is on the bottom.
   

5. The Trim slides on the inside of the flush frame of the opening. Push in until the trim is flush with the facing material.
   

6. The trim can slide in and out to the full depth of the facing material providing it falls within the depth limits of the trim kit. A construction adhesive can be used to better secure the trim.
   

DLT36, DLT36-2, DLT48, DLT48-2, DLT72, DLT72-2
1” ADJUSTABLE TRIM KIT

• The installation of this KIT must be done by a qualified and certified gas appliance installer.
• Check local codes and read all instructions prior to installation.

NOTICE
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.

WARNING
Some materials used in the manufacturing process of this product can expose you to Benzene which is known in the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65warnings.ca.gov

Assembly

1. The facing material should be fully finished before installation of the trim kit.

2. Slide the side pieces into the top and bottom tracks.

3. Ensure the all 4 corners of the trim kit are squared off.

4. The Trim slides on the inside of the flush frame of the opening. Push in until the trim is flush with the facing material.

5. The trim can slide in and out to the full depth of the facing material providing it falls within the depth limits of the trim kit.
   
   THIS SECTION ONLY FOR DISTINCTION TRIMS DLT72, DLT72-2

6. Secure the top of the trim to the finishing material with the included screw to prevent bowing of the top trim piece when heated.
   

References

• P65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>