KIT BUILDINGS SYSTEMS C2620 Container Shelter Instruction Manual

KIT BUILDINGS SYSTEMS C2620 Container Shelter

Specifications

• Length: 6m
• Width: 8m
• Height: 3m

Product Information

This container shelter model W8 x L6 x H3m C2620 does not include front and back panels. It comes with various parts as listed in the parts list, each identified with a part code for easy assembly.

The roof fabric needs to be tightened sufficiently to avoid sagging and should be re-tightened after a few months, especially during cold weather to prevent slackening.

It is the owner’s responsibility to remove snow promptly if it does not slide off on its own.

Product Usage Instructions

Before Assembly

1. Keep the work area clean and free of clutter.
2. Ensure children are kept away from the assembly area.
3. Maintain proper footing and balance during assembly.
4. Do not assemble under the influence of alcohol or drugs.

Equipment and Tools Required for Installation

• Measuring tape
• String for alignment
• Step ladder
• Welder
• Sledge hammer
• Wrench
• Scissors

Installation Process

Base Installation

1. Refer to the diagram (Figure 1) for placing the base plates ensuring square foundation.
2. Weld all base plates onto the containers.

Frame Installation

1. Refer to the diagram (Figure 2) for frame installation.
2. Place the roof cover evenly on the frame and adjust it square and centered.
3. Cut pockets in the cover for lower tensioning tubes, insert them, and tie down using straps.
4. Weld angle seats on each container and secure the cover using ropes tied to the angle seats.

FAQ

Q: What should I do if the roof fabric sags?
A: Tighten the roof fabric enough to avoid sagging, and re-tighten after a few months, especially in cold weather.

Q: Is it necessary to remove snow from the shelter?
A: It is the owner’s responsibility to remove snow promptly if it does not slide off on its own to prevent damage.

Q: Can the shelter withstand high winds?
A: Avoid setting up the shelter in high winds to prevent potential damage. Ensure proper anchoring for stability.

Model # W8 x L6 x H 3m
C2620 Container Shelter
Without Front & Back Panel

Parts List

SPECIFICATION

• Length: 6m
• Width: 8m
• Height: 3m

IMPORTANT—–READ MANUAL FIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause unnecessary and costly mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or twice again after a few months of use. This is important when assembly in cold weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric “slack” again and need to be re-tighten before next winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur. Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION

1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors

INSTALLATION PROCESS

BASE INSTALLATION
Please refer to the diagram (Figure 1) to place the base plates. UNIT: m

1. The measure is from center to center of the tubes. Referring to the above diagram and confirm the place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE.
2. All the base plates need use welder to be welded on the Containers.

FRAME INSTALLATION
Please refer to the diagram( Figure 2) to install the frame.

1. As Figure 2 shown find Top bent tube (part code 1), Middle bent tube (part code2) and Sidewall bent tubes (part code3). To connect them by Screw M8x70（part code 9）, which makes one group of arches. Please NOTE the direction of the screw. DO NOT install the screws on the top of the truss where the fabric will rest.
2. Lift an assembled arch into one base plate and force the other end of the arch into the opposite base plate.
3. As the following Figure 3 Shown, when finishing installing the first two arches,connect the Connection purlins onto them by using screw M10x80 （ part code 10）.There are 5 pieces of Connection purlins (part code 4) between two groups. Then install the third arch into base plate and connect the purlins. Finally install the Support tube (part code 5) using Screw M8x70（part code9）and Clip (part code 6). By turns the assembly for the frame is finished.
4. Please install the rest of other groups construction according to the first two groups.

INSTRUCTION FOR COVER ATTACHED

Install the Roof Cover

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail filled with air.

1. As Figure 4 shown, before assembly the roof cover, please insert the lower tensioning tube (part code7) into the pockets on end of the roof cover. And also put on the plastic plug.(part code12).
2. As Figure 5 shown, put the Roof cover (part code 8) EVENLY, CARRFULLR AND SLOWLY on the frame. Adjust the cover so that it is square and evenly centered on the frame.
3. As Figure 6 shown, Cut some pockets according to the position of the base plates and put the lower tensioning tubes for roof cover (part code 7) into the pocket of roof cover. Then use Straps (part code13) to tie down the Lower tensioning tubes like the Figure. Finally install the∮32 Plastic plug for base rail section (part code 12) into two end of the lower tensioning tubes.
4. As Figure 7 shown, weld the Angle seats (part code14) on each container and use Ropes (part code 11) to knit the cover on the two side arches, finally tie the Roof cover to the Angle seats.

NOTE: DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANY

CIRCUMSTANCES until the final assembly and tightening has been completed.
The process is quite easy. But some tightening adjustments will be necessary to produce a flat, tensioned roof cover. Please adjust the roof cover every month.

FRONTWALLWITH DOOR
FOR
C2640/C2620
(CONTAINER OUTSIDE THE SHELTER)

Spare Parts List

Frontwall with door Assembly

According to above Figure to find out all spare parts for frontwall, connect them together by using screw, make sure the spacing. There are stake pegs for base plates.

Find out the back cover(No. 20), use ropes(No. 23) to tie it to the back wall.
Adjust and tighten them once per month after assembly to make sure them works perfect.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>