LOVMOR W2436-E Wall Mounted Bathroom Medicine Cabinet Instruction Manual
- June 17, 2024
- LOVMOR
Table of Contents
LOVMOR W2436-E Wall Mounted Bathroom Medicine Cabinet
Specifications
- Model: W2436-E, W2736-E
- Hardware Contents:
- Soft-close hinge x 4
- Corner brace x 16
- Adjustable shelf clip x 8
- Flat head Phillips screws x 8 (1/2 inch)
- Round head Phillips screws x 68 (1/2 inch)
- Round head Phillips screws x 12 (3/4 inch)
- Tools Required (Not Included): Phillips screwdriver
Product Usage Instructions
Caution
Be sure to carefully remove all parts from the carton and check for damages. Keep hardware away from children. Assembly is recommended with two adults.
Assembly Overview
- Attach Box Side Panel – Left (A1) using 1/2 round head Phillips screws x 10.
- Attach Box Side Panel – Right (A2) using 1/2 round head Phillips screws x 10.
- Continue assembling the sides, bottom, back panel, and top panel following the provided instructions.
- Install the adjustable shelf using the clips provided.
- Attach the face frame and door panel with the specified screws.
- Adjust the hinges as needed to ensure proper door alignment.
Troubleshooting
If the door is not level after installation, adjust the hinges by turning the screws clockwise or counterclockwise as necessary.
FAQ
Q: What should I do if I find damaged parts?
A: Contact the customer service team at the retailer where you purchased the product for assistance with replacement parts.
Q: Can I assemble the product alone?
A: While assembly is possible alone, it is recommended to have two adults for ease and safety.
Q: Are the hinges pre-installed?
A: Some products may come with hinges pre-installed, but always refer to the provided instructions for installation guidance.
Q: How do I adjust the door alignment?
A: Turn the screws on the hinges clockwise to extend or counterclockwise to shorten for proper door alignment.
Product Overview
| PART | DESCRIPTION |
|---|---|
| A1 | Box side panel – left |
| A2 | Box side panel – right |
| B | Box bottom panel |
| C | Box back panel |
| PART | DESCRIPTION |
| --- | --- |
| D | Face frame |
| J | Door panel |
| K | Adjustable Shelf |
| L | Box top panel |
CAUTION
- Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them.
- The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly.
- Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended.
- Do not tighten all the screws until all the adjacent parts have been properly connected.
Please do not throw away extra screws.Please refer to the actual product for the screw hole position.
HARDWARE CONTENTS
-
CC:Soft close hinge x 4
Be careful the length of the screws. -
EE: Corner brace x 16
-
FF: Adjustable shelf clip x 8
-
GG: 1″ Flat head Phillips screw x 6
-
HH: Rubber bumper x 4
TOOLS REQUIRED (NOT INCLUDED)
INSTALLATION OVERVIEW
Use 1/2″ round head Phillips screw × 10 
Use 1/2″ round head phillips screw x 10
Use 1/2″ round head phillips screw
x 12
Use 1/2″ round head phillips screw
x 12
1″ Flat head Phillips screw x 6
Use 1/2″ round head phillips screw x 14
Use 1/2″ round head phillips screw x 2
Adjustable shelf clip x 8
Use 1/2″ flat head phillips screw x 4
3/4″ Round Head Phillips Screw x 4
Some products may have hinges pre-installed.
If the door is not level when it is installed, the customer will need to turn the screw clockwise to extend the hinge or counterclockwise to shorten the hinge.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>