LOVMOR 3DB30-E Drawer Base Cabinet Instruction Manual
- June 17, 2024
- LOVMOR
Table of Contents
LOVMOR 3DB30-E Drawer Base Cabinet
Product Specifications
- Model: 3DB30-E
- Drawer Base Cabinet
Product Usage Instructions
Part Identification:
Refer to the manual for part identification. Ensure all parts are present and undamaged before assembly.
Assembly Precautions:
- Keep hardware away from children.
- Assembly is recommended with two adults.
- Follow instructions carefully for proper assembly and operation.
Hardware Contents:
- Glide and runner profile x 6
- Adjustable drawer clips x 6
- Wood corner block x 4
- Corner brace x 13
- Rubber bumper x 12
Tools Required:
Tools required for installation are not included. Ensure you have the
necessary tools before assembly.
Installation Overview:
Follow the step-by-step installation overview provided in the manual
carefully for the proper assembly of the drawer base cabinet.
Drawer Installation:
- Insert the drawer on the extended runner.
- Secure the drawer clips with the runner by pushing the drawer in until a click is heard.
- To level the drawer, adjust using the green spur gears as indicated in the manual.
- To remove the drawer, push the green clips simultaneously to unlock the drawer clips.
Frequently Asked Questions (FAQ):
-
Q: Can I assemble the product alone?
A: It is recommended to assemble the product with two adults to ensure proper assembly and safety. -
Q: What should I do if I find damaged parts?
A: If you find any damaged parts, contact customer support for assistance and replacement.
MODEL : 3DB30-E
DESCRIPTION
| PART | DESCRIPTION |
|---|---|
| A1 | Box side panel – left |
| A2 | Box side panel – right |
| B | Box bottom panel |
| C | Box back panel |
| D | Face frame |
| E | Toe kick panel |
| PART | DESCRIPTION |
| --- | --- |
| F1 | Drawer face panel |
| F2 | Drawer face panel |
| G1 | Drawer side panel – left |
| G2 | Drawer side panel – right |
| H | Drawer bottom panel |
| I | Drawer back panel |
CAUTION
- Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them.
- The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly.
- Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended.
- Do not tighten all the screws until all the adjacent parts have been properly connected. Please do not throw away extra screws.Please refer to the actual product for the screw hole position.
HARDWARE CONTENTS
TOOLS REQUIRED (NOT INCLUDED)
INSTALLATION OVERVIEW
- Use 1/2” round head phillips screw x 10
- Use 1/2” round head phillips screw x 10
- Use 1/2” round head phillips screw x 2
- Use 1/2” round head phillips screw x 2
- Use 1/2” round head phillips screw x 8
- Use 1/2” round head phillips screw x 20
- Use 5/8” flat head phillips screw x 12
- Use 5/8” flat head phillips screw x 12
- Use 5/8” flat head phillips screw x 4 Be careful of the screw type.
- Use 3/8” flat head phillips screw x 4 Be careful of the screw type.
- Insert the drawer on the extended runner. To secure the drawer clips with the runner, push the drawer in. Upon successful locking, a click can be heard.
- Ensure that the hook on each runner profile fits into the corresponding holes on the drawer back panel.
- To level the drawer, use the green spur gears 1 to adjust drawer left and right, the green spur gears 2 to adjust drawer up and down, and the green spur gears 3 to adjust drawer inside and outside.
- To take the drawer out, push the green clips at the same time to unlock the drawer clips.
- Use 1” flat head phillips screw x 8
Dear customers,
Thank you for purchasing our product. If you require assistance, please
contact the customer service team at the retailer where you purchased the
product. The customer service team will be happy to assist you.