UME 6938501345 Solar Motion Sensor Outdoor Light Owner’s Manual

UME 6938501345 Solar Motion Sensor Outdoor Light

Specifications

• Model: #6938501345-2pcs
• Quantity: 2 Wall Lantern Fixtures
• Hardware Contents: 4 Screws, 4 Plastic Anchors
• Estimated Assembly Time: 10-20 minutes
• Tools Required: Phillips Screwdriver, Electric Drill, Ladder

Product Usage Instructions

Preparation

Before assembling or installing the lighting fixture:

• Ensure all parts are present as per the package contents list.
• If any part is missing or damaged, do not proceed.

Installation

1. Choose a desired location for the fixture and mark drill hole positions.
2. Drill holes using a suitable drill bit and plug with plastic anchors.
3. Attach the fixture using screws and a Phillips screwdriver.
4. Adjust the lamp head to the desired position.

Operating Instructions

1. Switch to desired mode: 1 mode or 2 mode based on your preference.
2. In 2 mode: Light on when motion is detected, off when motion leaves.
3. In 1 mode: Light on when motion is detected, turns to low brightness when motion leaves.

Care and Maintenance

Regular maintenance is key to optimal performance:

• Check for dust and debris on the solar panel regularly.
• If the light stays dim, ensure the panel receives adequate sunlight.
• Clean the solar panel to remove any obstructions.

FAQ

Q: What should I do if the light does not come on?

A: Check if the battery is low or drained. Charge the battery fully if needed.

Q: How can I improve charging in low-light conditions?

A: Reposition the solar panel to receive more sunlight or wait for a sunny day for better charging.

Q: What if the light stays dim despite being fully charged?

A: Clean any dust and debris from the solar panel to ensure proper charging.

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Do not put the battery in fire – it may explode.
• Do not immerse into water.
• Do not expose the light to fire or intense heat as the battery may explode.
• The solar charger board should be set in a sunny area, where maximum sunlight can be collected.
• Typically, the solar board should face a direction (south) where sunlight can charge the board for at least 3 hours per day (5 hours per day if behind glass). It is suggested to charge the light for 24 hours before first use.

PREPARATION

Before beginning to assemble or installing lighting fixture, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Estimated Assembly Time: 10-20 minutes. Tools Required for Assembly: Phillips Screwdriver, Electric Drill, Ladder

INSTALLATION

1. Choosing a desired location for the fixture (A), then mark the position of the drill holes by using a pencil.
2. Drill with a suitable drill bit (7/32 in.) and plug the mounting holes with plastic anchors (BB).
3. Attach the light fixture (A) to the mounting holes using the screws (AA) with a Phillips screwdriver (not included).
4. Rotate the lamp head to the desired position

OPERATING INSTRUCTIONS

1. Move the switch to the desired mode.
2. Using 2 mode:
   • Light on when the sensor detects motion.
   • Light off when the motion leaves.
3. Using 1 mode:
   • Light on when the sensor detects motion.
   • Light turns to low brightness when the motion leaves.

CARE AND MAINTENANCE

1. To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.
2. Periodically clean the solar panel with a soft cloth and warm water.
3. Keep the panel clear of snow and leaves.
4. Make sure trees and other objects do not block sunlight from the panel.
5. Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish.
6. This is not a defect in the finish and will not be covered by the warranty.
7. Do not spray the light fixture with a hose or power washer.

TROUBLESHOOTING

.

| 2.    The light may be detecting daylight or light from another source preventing the light from coming on.| 2.| Relocate the light.
| | |
The light stay in a low brightness, the battery does not fully charge.| 1. If there is overcast days, the solar panel may not convert enough daylight to recharge the battery sufficiently.| 1.     Wait for a sunny day.

2.     Reposition the solar panel to receive more sunlight.

3.     Clean dust and debris from solar panels.

| 2. There is no enough sunlight.
| ****

3. There is dust and debris on the solar panel.

WARRANTY

3-YEAR LIMITED WARRANTY

If this product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge. This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights and you may have other rights that vary from state to state. IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC:

• 149B Houston Rd Troutman NC 28166
• Ningbo UME Lighting Co., LTD
• CN8, Far East Industry Park, Yuyao, China
• Help@umelux.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>