UME 5290205053 Dusk to Dawn LED Outdoor Wall Light Fixtures Owner’s Manual
- June 14, 2024
- UME
Table of Contents
5290205053 Dusk to Dawn LED Outdoor Wall Light Fixtures
Owner’s Manual
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
PACKAGE CONTENTS
| PAR | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
HARDWARE CONTENTS (not shown actual size)
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
WARNING:
- Consult a qualified electrician if you are not certain about the installation process. Always install wiring connections in accordance with local code, ordinances and the National Electric Code.
- hanges or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This light fixture is designed to fit standard junction boxes as defined by the National Electrical Code.
- This light fixture is not dimmable.
This Class B digital apparatus complies with Canadian ICES-005.
NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
PREPARATION
Before beginning to assemble or installing lighting fixture, make sure all
parts are present. Compare parts with package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to assemble,
install or operate the product.
Estimated Assembly Time: 20-30 minutes. Tools Required for Assembly: Phillips
Screwdriver, Silicone Caulking Adhesive, Ladder.
INSTALLATION
-
Turn OFF power to work area at main circuit breaker or fuse box.
CAUTION: Do not rely on wall switch alone to turn off power. -
Remove the crossbar from the fixture (A) by unscrewing the pre-assembled nuts. Put these two nuts a side as they will be used later.
-
Attach the crossbar to the junction box (not included) using the two screws (AA).
-
Connect the ground wire from the junction box to the ground screw on the crossbar. Then connect the ground wire from the junction box to the ground wire from the fixture (A) by twisting a wire nut (BB) onto the bare ends of the wires.
Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box. -
Attach the light fixture (A) to the crossbar using the nuts previously removed in step 2.
-
After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.
-
Turn ON power to work area at main circuit breaker or fuse box.
CARE AND MAINTENANCE
- Clean surfaces with a mild, non-abrasive cleaner.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| The light will not go on. | 1. No power. |
2. Fixture may be wired incorrectly.
3. Switch may be wired incorrectly.| 1. Make sure lamp fixture is plugged in
and power is on.
2. Check wiring.
3. Check wiring.
Fuse blows or circuit trips when fixture is turned on.| Crossed wires or power
wire is grounding out.| Consult a certified electrician.
3-YEAR LIMITED WARRANTY
If this product fails due to a defect in materials or workmanship within three
(3) years from the date of purchase, return it along with proof of date of
purchase and it will be replaced with the same or comparable model free of
charge.
This warranty is void if damage or defect has resulted from accident, abuse,
misuse or faulty repair. This warranty gives you specific legal rights and you
may have other rights that vary from state to state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR
INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO
YOU.
LUTEC USA LLC:
149B Houston Rd Troutman NC 28166
Ningbo UME Lighting Co., LTD
CN8, Far East Industry Park, Yuyao, China
Help@umelux.com
Printed in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>