UME 6940101125-2pcs Motion Sensor Outdoor LED Wall Light Owner’s Manual

UME 6940101125-2pcs Motion Sensor Outdoor LED Wall Light

IMPORTANT
RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

PACKAGE CONTENTS

HARDWARE CONTENTS

HARDWARE CONTENTS (not shown actual size)

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Do not put the battery on fire – it may explode.
• Do not immerse in water.
• Do not expose the light to fire or intense heat as the battery may explode.
• The solar charger board should be set in a sunny area, where maximum sunlight can be collected. Typically, the solar board should face a direction (south) where sunlight can charge the board for at least 3 hours per day (5 hours per day if behind glass). It is suggested to charge the light for 24 hours before first use.

PREPARATION

Before beginning to assemble or install lighting fixtures, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.

• Estimated Assembly Time: 10-20 minutes.
• Tools Required for Assembly: Phillips Screwdriver, Electric Drill, Ladder.

INSTALLATION

1. Choosing a desired location for the fixture (A), then mark the position of the drill holes by using a pencil.
2. Drill with a suitable drill bit (7/32 in.) and plug the mounting holes with plastic anchors (BB).
3. Insert the screws (AA) into the mounting holes by using the Phillips screwdriver.
4. Leave 0.2 in. of the screws exposed. Hang the fixture (A) on the two screws (AA).

OPERATING INSTRUCTIONS

1. Move the switch to the desired mode.
2. Using ON mode: Light on at night; the sensor is off.
3. Using AUTO mode:
   • Light on when the sensor detects motion.
   • Light off when the motion leaves.
4. Using DIM mode:
   • Light on when the sensor detects motion.
   • The light turns to low brightness when the motion leaves.

BATTERY CHANGE

1. Detach the diffusor by unscrewing the screws pre-assembled in the fixture with a Phillips screwdriver.

2. Detach the LED plate by unscrewing the screws on the LED plate with a Phillips screwdriver.

3. Take out the old battery from the battery compartment.
   CAUTION: Batteries must be recycled or destroyed appropriately.

4. Install a new battery (3.7 V 1500 mAh Li-ion).

5. Install the LED plate using the screws removed in step 2.

6. Install the diffusor using the screws removed in step 1.

CARE AND MAINTENANCE

• To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.
• Periodically clean the solar panel with a soft cloth and warm water.
• Keep the panel clear of snow and leaves.
• Make sure trees and other objects do not block sunlight from the panel.
• Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish.
• This is not a defect in the finish and will not be covered by the warranty.
• Do not spray the light fixture with a hose or power washer.

TROUBLESHOOTING

PROBLEM

| POSSIBLE CAUSE|

CORRECTIVE ACTION

---|---|---
The light will not come ON.| 1.     The battery is low or drained.

2.     The light may be detecting daylight or light from another source preventing the light from coming on.

| 1.     Charge the battery fully.

2.     Relocate the light.

The light stays at a low brightness, and the battery does not fully charge.| 1. If there are overcast days, the solar panel may not convert enough daylight to recharge the battery sufficiently.| 1.     Wait for a sunny day.

2.     Reposition the solar panel to receive more sunlight.

3.     Clean dust and debris from solar panels.

 | 2.  There is not enough sunlight.
 | 3. There is dust and debris on the solar panel.

3-YEAR LIMITED WARRANTY

• If this product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge.
• This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
• IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC:

• 149B Houston Rd Troutman NC 28166 Ningbo UME Lighting Co., LTD CN8, Far East Industry Park, Yuyao, China
• Help@umelux.com.

Printed in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>