LOG BARN A03255 Industrial Black Dome Island Chandelier Modern Farmhouse Instruction Manual

June 17, 2024
LOG BARN

LOG BARN A03255 Industrial Black Dome Island Chandelier Modern Farmhouse

LOG BARN A03255 Industrial Black Dome Island Chandelier Modern
Farmhouse

SAFETY INFORMATION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

LOG BARN A03255 Industrial Black Dome Island Chandelier Modern
Farmhouse

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

  • Ladder
    Tool Required

  • Phillips head, flat blade screwdriver
    Tool Required

  • Electrical tape

  • Pliers
    Tool Required

  • Wire Cutter / Stripper
    Tool Required

PARTS TYPE & QTY INCLUDING

(B) Round mounting plate (1)
(C) Green ground screw (1)
(E) Canopy (1)
(F) Swivel joint (1)
(G) Knob ball (2)
(H) Tube (4)
(I) Fixture (1)
(J) Metal shade (3)
(L) Socket ring (3)

ACCESSORIES & QTY ENCLOSED

(A) Plastic wire connector (3)
(D) Mounting screw (2)

Product Description

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the  “OFF” position. B). Place the wall switch in the “OFF” position.

  3. Place metal shade (J) over the sockets of fixture (I), then secure with socket rings (L)
    Assembly & Installation Instructions

  4. Unscrew the knobs from canopy then remove the mounting plate (B)
    Assembly & Installation Instructions

  5. According your desired hanging length to choose and use the tubes (H). Pass wires through the chosen tubes (I) , swivel joint (F) and canopy (E), Thread the chosen tubes (I) , swivel joint (F), canopy (E) and fixture (J) together. Hand tighten until snug..
    Installation

  6. If needed, cut off the extra power cord length on the 2 wire cord and bare ground wire so that they all are at least 6 inches (152.4 mm) long from the canopy (E).
    Assembly & Installation Instructions

  7. Carefully pass the outlet box wires through mounting plate (B) Attach the mounting plate(B) to outlet box with the mounting screws (D)
    Assembly & Installation Instructions

  8. Make wire connections
    Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE , NEVER CONNECT WIRES TO GROUND WIRES
    Connect ground wire according to below chart
    Connect ground wire according to below chart
    Connect wires according to below chart
    * Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
    ---|---
    Black| White
    Parallel cord (round & smooth)| Parallel cord (square & ridged)
    Clear, Brown. Gold or Black without tracer| Clear. Brown, Gold or Black with tracer
    Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
    Note:** When parallel wires (SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)|

Twist plastic wire connector until wires are tightly joined together, wrap each connector with approved  electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  1. Raise canopy (E) to ceiling and secure canopy (E) in place by tightening knobs (G) onto the threaded nipple on mounting plate (B)
    Assembly & Installation Instructions

  2. Install the bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.)
    Assembly & Installation Instructions

  3. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals