Ubuy 28990695 Farmhouse Chandelier Instruction Manual

Ubuy 28990695 Farmhouse Chandelier

Product Specifications

• Product Name: Hanging Pendant Light Fixture
• Model Number: HPF-1000
• Material: Iron, Wood
• Maximum Wattage: 60W
• Power Source: Electric Hardwired

Product Usage Instructions

1. Pre-Installation Preparation:

Before starting assembly and installation, ensure you have the following tools ready:

• Chain pliers
• Mounting screws
• Quick links
• Wire connectors
• Electrical tape

2. Installation Steps:

Step A: Adjust Wooden Arms

Adjust wooden arms (M) to the proper position. Pass finial (P) through iron plate (O) and tighten ball nut (N) to finial (P).

Step B: Hanging Height Adjustment

Determine the correct number of links needed for proper hanging height. Use chain pliers to disconnect and discard any excess chain. Attach quick link (H) to chain (I) and loop (J) on the upper cover.

Step C: Electrical Connection

Connect wires as per the provided chart. Ensure proper grounding and wire connections. Secure all wires tightly with wire connectors and electrical tape.

Step D: Final Installation

Raise canopy (E) to the ceiling and secure it in place. Install bulbs with wattage not exceeding the recommended maximum.

3. Final Checks and Power On:

Ensure all components are properly installed before turning on the light. Once confirmed, turn on the power and enjoy your new pendant light fixture.

Frequently Asked Questions

Q: Can I install the pendant light fixture myself?

A: While installation instructions are provided, it is recommended to have a licensed electrician perform the installation to reduce risks.

Q: What is the maximum wattage for bulbs in this fixture?

A: The maximum recommended wattage for bulbs in this fixture is 60W. Do not exceed this limit to ensure safety.

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

TOOLS REQUIRED

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Single bar (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Collar ring (1)
• (G) Collar loop (1)
• (H) Quick link (2)
• (I) Chain (1)
• (J) Loop (1)
• (K) Upper cover（1）
• (L) Threaded pipe (1)
• (M) Wooden arm (4)
• (N) Ball nut (3)
• (O) Iron plate (1)
• (P) Finial (1)

ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation

   • Step A1: Adjust wooden arms (M) to the proper position.
   • Step A2: Pass finial (P) through iron plate (O) and tighten ball nut (N) to finial (P).
   • Step A3: Carefully pass the fixture wires through threaded pipe (L) and upper cover (K), then screw loop (J) onto threaded pipe (L).
   • Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted parts.
   • Step B2: Attach quick link (H) to chain (I) and loop (J) on the top of the upper cover (K).
   • Step B3: Carefully weave the fixture wires through the chain (I) in and out of every other link and stop just when you reach the top of the chain (I). Gently pull the wires to ensure the wires are not stressed.

3. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.

4. Make installation

   • Step C1: Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
     Note: the side of single bar (C) marked “GND” must face out.

   • Step C2: Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position
     Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you would know the proper position where collar loop (G) should be located.
     Note: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed enough threads (no less than 6 threads) on the pre-assembled threaded nipple for more secure hanging. If not, adjust collar loop (G) on single bar assembly (C) by screwing collar loop (G) in or out of single bar (C) until the secure length is achieved

   • Step C3: Pass chain (I) through collar ring (F) and then through canopy (E).

   • Step C4: Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H).

   • Pass the fixture wires through collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.

   • Step C5: If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.

   • Step C6: Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Note: When parallel wires (SPT | & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus. )

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step C7: Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
• Step C8: Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is already installed properly, and then you can turn on the light. Enjoy! CLEANING.

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>