FLASH F7100555 7X40W BIG EYE PRO User Manual

June 17, 2024
FLASH

SERIES: EVENT

FLASH F7100555 7X40W BIG EYE PRO - cover

7X40W BIG EYE PRO
User Manual

https://flash-butrym.pl/en_US/p/4x-7X40W-BIG-EYE-PRO/723

F7100555 7X40W BIG EYE PRO

WARNING! The Led Moving Head (LMH) has a powerful pan and tilt motor.
The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the LMH unless the baase is
securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The LMH lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LMH, as intense illumination can damaged the display.

FLASH F7100555 7X40W BIG EYE PRO - overview 1

INTRODUCTION

THANK YOU FOR PURCHASING 7X40W BIG EYE PRO. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

  • Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.

  • Unpack and check carefully  here is no transportation damage before using the fixture.

  • Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.

  • It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

  • Disconnect main power before servicing and maintenance.

  • Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.

  • Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.

  • In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself.
    Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

  • Do not connect the device to any dimmer pack.

  • Do not touch any wire during operation and there might be a hazard of electric shock.

  • To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.

  • The housing must be replaced if they are visibly damaged.

  • Do not look directly at the light spot while the fixture is on.

PRODUCT INFORMATION

  • Light Source: LED RGBW 7x40W RGBW
  • Power consumption: 350W
  • Power supply voltage: 100-240V, 50/60Hz AC
  • PAN range: 540°
  • TILT range: 270°
  • Beam angle (min/max): 3,5°-55°
  • Features: CTO, Zoom, Macro Colors, Variable Strobo
  • Operating modes: DMX, Auto, Sound-controlled, Master, Slave, RDM
  • DMX channel mode: 2 3 / 3 5 / 5 1
  • IP Rating: IP20
  • Housing made: ABS
  • Cooling: Active
  • AC IN/OUT: TrueCon
  • 3-Pin XLR DMX Input/Output
  • Net Weight: 9,8 kg
  • Dimensions: H(41)xW(31)xD(23) cm

INSTALATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.
Regardless of the rigging option ypu chose for our fixture, always be sure to secure your fixture with safety cable. The fixture provides a builitin rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.

CONNECTION

The device is equipped with the following interfaces:

  1. DMX (in/out): XLR 3(5)-pin socket
  2. Power (in/out): TrueCon socket
    The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.
Diagram of connection of devices by DMX cable.

FLASH F7100555 7X40W BIG EYE PRO - CONNECTION 2

IMPORTANT! The maximum number of devices connected in series via power cable is 3 pcs.
The connection is performed using power cable with TrueCON connector (included). The device must be operated by qualified personnel.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions
Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

Voltage Specification.

Input Voltage Amperage Frequency Total Power
230[V] AC 1.13[A] 50[Hz] 350[W]

Manual Menu

  1. DMX ADDRES — ENTER — 001-512

  2. SET — ENTER
    RUN MODE — ENTER — DMX / AUTO 1 / AUTO 2 / SOUND
    CHANELL MODE — 23CH / 35CH / 51CH
    PAN INWERT — ENTER — ON / OFF
    TILT INWERT — ENTER — ON / OFF
    HALL CRCT — ENTER — ON / OFF
    ENCODER — ENTER — ON / OFF
    SIGNAL KEEP — ENTER — ON / OFF
    SCREEN SAVER — ENTER — AUTO / ON / OFF
    UPDATE SLAVE — ENTER — ON / OFF
    LANGUAGE —- ENTER —- ENG / CH
    LOAD DEFAULT — ENTER — OK / CANCEL

  3. MANUAL — ENTER —- POSSIBILITY OF MANUAL SETTINGS OF EACH
    PRE-SELECTED MODES 23CH / 35CH / 51CH

  4. CALIBRACJON — ENTER — CALIBRATION OF THE DEVICE FUNCTIONS

  5. RESET — ENTER — RESET EFFECT / RESET SCAN / RESET ALL

  6. NOTE — ENTER — SYSTEM INFO

DMX CHART

23 CH

1| PAN| 0-255|
---|---|---|---
2| PAN FINE| 0-255|
3| TILT| 0-255|
4| TILT FINE| 0-255|
5| PAN /TILT SPEED| 0-255|
6| ZOOM| 0-255|
7| ZOOM ROTATION| 0-255|
8| DIMMER| 0-255|
9| STROBO| 005-103| STROBO SLOW TO FAST
| | 104-107| LIGHT ON
| | 108-207| PULS STROBO SLOW TO FAST
| | 208-212| LIGHT ON
| | 213-251| RANDOM STROBO SLOW TO FAST
| | 252-255| LIGHT ON
10| RED| |
11| GREEN| |
12| BLUE| |
13| WHITE| |
14| CTO| |
15| MACRO| |
16| STATIC EFFECT| 000-029| LIGHT ON
| | 030-044| EFFECT 1
| | 045-059| EFFECT 2
| | 060-074| EFFECT 3
| | 075-089| EFFECT 4
| | ……|
| | 120-134| EFFECT 7
STATIC EFFECT MACRO COL.| 135-149| EFFECT 8
| | 150-164| EFFECT 9
| | 165-179| EFFECT 10
| | 180-209| EFFECT 11
| | 210-224| EFFECT 12
| | 225-239| EFFECT 13
| | 240-254| EFFECT 14
| | ……|
| | 255| EFFECT 15
17| DYNAMIC EFFECT| 000-008| LIGHT ON
| | 009-014| EFFECT 1
| | 015-019| EFFECT 2
| | 020-029| EFFECT 3
| | 030-034| EFFECT 4
| | 035-039| EFFECT 5
| | ……|
| | 080-084| EFFECT 13
| | 085-089| EMPTY
| |  090-094| EFFECT 14
| | ……|
| | 120-124| 120-124 EFFECT 20
DYNAMIC  EFFECT MACRO COL.| 125-129| EFFECT 21
| | 130-134| EFFECT 22
| | 135-139| EFFECT 23
| | 140-144| EFFECT 24
| | ……|
| | 200-204| EFFECT 36
| | 205-255| EFECT 37
18| DYNAMIC SPEED| |
19| BACKGR. RED| |
20| BACKGR. GREEN| |
21| BACKGR. BLUE| |
22| BACKGR. WHITE| |
23| RESET| |

35 CH

1| RED| 0-255|
---|---|---|---
2| RED FINE| 0-255|
3| GREEN| 0-255|
4| GREEN FINE| 0-255|
5| BLUE| 0-255|
6| BLUE FINE| 0-255|
7| WHITE| 0-255|
8| WHITE FINE| 0-255|
9| CTO| 0-255|
10| MACRO| 0-255|
11| STROBO| 005-103| STROBO SLOW TO FAST
| | 104-107| LIGHT ON
| | 108-207| PULS STROBO SLOW TO FAST
| | 208-2120| LIGHT ON
| | 213-251| RANDOM STROBO SLOW TO FAST
| | 252-255| LIGHT ON
12| DIMMER| 0-255|
13| DIMMER FINE| 0-255|
14| PAN| 0-255|
15| PAN FINE| 0-255|
16| TILT| 0-255|
17| TILT FINE| 0-255|
18| FUNCTION| 0-255|
19| RESET| 0-255|
20| ZOOM| 0-255|
21| ZOOM ROTATION| 0-255|
22| SHAPE SELECTION| 0-255|
23| SHAPE SPEED| 0-255|
24| SHAPE FADE| 0-255|
25| SHAPE RED| 0-255|
26| SHAPE GREEN| 0-255|
27| SHAPE BLUE| 0-255|
28| SHAPE WHITE| 0-255|
29| SHAPE DIMMER| 0-255|
30| BACKGR.  DIMMER| 0-255|
31| SHAPE TRANSITION| 0-255|
32| SHAPE OFF SET| 0-255|
33| FOREGR. STROBE| 0-255|
34| BACKGR. STROBE| 0-255|
35| BACKGR. SELECTION| 0-255|

51 CH

1| PAN| |
---|---|---|---
2| PAN FINE| |
3| TILT| |
4| TILT FINE| |
5| PAN /TILT SPEED| |
6| ZOOM| |
7| ZOOM ROTATION| |
8| DIMMER| |
9| STROBO| 005-103| STROBO SLOW TO FAST
| | 104-107| LIGHT ON
| | 108-207| PULS STROBO SLOW TO FAST
| | 208-212| LIGHT ON
| | 213-251| RANDOM STROBO SLOW TO FAST
| | 252-255| LIGHT ON
10| RED| |
11| GREEN| |
12| BLUE| |
13| WHITE| |
14| CTO| |
15| MACRO| |
16| STATIC EFFECT| 000-029| LIGHT ON
| | 030-044| EFECT 1
| | 045-059| EFECT 2
| | 060-074| EFECT 3
| | 075-089| EFECT 4
| | ……|
| | 120-134| EFECT 7
STATIC EFECT MACRO COL.| 135-149| EFECT 8
| | 150-164| EFECT 9
| | 165-179| EFECT 10
| | 180-209| EFECT 11
| | 210-224| EFECT 12
| | 225-239| EFECT 13
| | 240-254| EFECT 14
| | ……|
| | 255| EFECT 15
17| DYNAMIC EFFECT| 000-008| LIGHT ON
| | 009-014| EFECT 1
| | 015-019| EFECT 2
| | 020-029| EFECT 3
| | 030-034| EFECT 4
| | 035-039| EFECT 5
| |  ……|
| | 120-124| EFECT 20
DYNAMIC  EFECT MACRO COL.| 125-129| EFECT 21
| | 130-134| EFECT 22
| | 135-139| EFECT 23
| | 140-144| EFECT 24
| | ……|
| | 200-204| EFECT 36
| | 205-255| EFECT 37
18| DYNAMIC SPEED| |
19| BACKGR.  RED| |
20| BACKGR.  GREEN| |
21| BACKGR.  BLUE| |
22| BACKGR.  WHITE| |
23| RESET| |
24| RED 1| |
25| GREEN 1| |
26| BLUE 1| |
27| WHITE 1| |
28| RED 2| |
29| GREEN 2| |
30| BLUE 2| |
31| WHITE 2| |
32| ……| |
33| ……| |
48| RED 7| |
49| GREEN 7| |
50| BLUE 7| |
51| WHITE 7| |

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FLASH User Manuals

Related Manuals