LEVOLOR 187689 Roller Shades Fabric Instruction Manual

LEVOLOR 187689 Roller Shades Fabric

Specifications

• Child Safety Warning
• Includes Cord Tension Device and Hold-Down Brackets
• Mounting Brackets included based on shade width

Product Usage Instructions

Installation

Ensure installation brackets are mounted correctly before proceeding. Review window terminology for inside or outside mount.

Mounting Types and Window Terminology

• Inside Mount: Mounting the shade inside the window frame or casing.
• Outside Mount: Mounting the shade outside the window opening.

Components Included

• Mounting Brackets (L bracket only required on outside mount)
• Cord Loop Tension Device
• Hex Head Screws (2 per Bracket)
• Hold Down Brackets (optional)

Tools and Fasteners You May Need (not included)

Refer to the user manual for a list of tools and fasteners that may be required for installation.

Operation

Learn how to operate the shade safely to ensure proper functioning.

Uninstall

Follow the instructions to safely remove the shade when needed.

Cleaning and Care

Refer to the cleaning instructions provided to maintain the shade in good condition.

Additional Information and Support

• Troubleshooting tips are available in case of any issues.
• Warranty details for product coverage.
• Contact Customer Service for further support or replacement parts.

FAQ

Q: How many brackets are included per shade based on width?
A: The number of brackets included varies based on the width of the shade. Refer to the table provided in the manual for details. Q: Are hold-down brackets necessary for installation? A: Hold-down brackets are optional but recommended for added safety and stability. Q: Where can I obtain replacement parts? A: Contact Customer Service at 1-800-538-6567 for replacement parts.

Roller Shades–Fabric/Solar/Banded

Continuous Cord Loop Lift Control–Cassette Valance

CHILD SAFETY

WARNING

Young children can STRANGLE in cord loops. They can also wrap cords around their neck and STRANGLE.

• Always keep cords out of the reach of children.
• Move cribs, playpens and other furniture away from cords. Children can climb furniture to get to cords.

Cord Loop Tension Device

• Attach the tension device on the cord loop to the wall or window casement. See “Install the Tension Device” on page 11. This can prevent children from pulling cord loops around their necks.
• For the shade to operate properly, the cord tensioner must be correctly mounted and secured.
• Fasteners provided in this kit may not be appropriate for all mounting surfaces. Use appropriate anchors for mounting surface conditions.
• Only supplied tension device and hardware should be used. Replacement parts may be obtained by contacting Customer Service at 1-800-538-6567.

Canadian Residents Only: For more safety information: 1-866-662-0666 or visit www.canada.ca, search “blind cords”.

WARNING: Keep all small parts, components and packaging away from children as they pose a potential choking hazard which may result in serious injury or death. Please reference all warning tags and labels in the instructions and on the shade.

WINDOW AND SHADE TERMINOLOGY

Thank you for purchasing LEVOLOR® Roller Shades. With proper installation, operation, and care, your new roller shade will provide years of beauty and performance. Please thoroughly review this instruction booklet before beginning installation.

MOUNTING TYPES AND WINDOW TERMINOLOGY

If the installation brackets are mounted correctly, the rest of the installation process follows easily. To prepare for this important first step, review the mounting types and basic window terminology illustrated below.

WINDOW AND SHADE TERMINOLOGY

INSTALLATION OVERVIEW

• Leaving the shade rolled up completely will ease installation.
• Confirm that the headrail and shade are the proper width and length.
• If installing several sets of shades, be sure to match them with the appropriate window.
• Check the installation surface to ensure that you have suitable fasteners and tools.
• Lay out and organize all parts and components.

Installation Brackets

Installation Brackets

Your order will include the correct number of installation brackets for your shade width, as shown in the table below
Shade Width (inches)| Number of Brackets per Shade
Up to 36| 2
36 to 54| 3
54 to 72| 4
72 to 108| 5
108 to 144| 6
2-on-1 Headrail Shades| 2 additional brackets provided

GETTING STARTED

COMPONENTS INCLUDED IN THE BOX

• Shade
• Mounting Brackets
• Installation Hardware

Optional items will be included, if selected at time of shade order.

GETTING STARTED

TOOLS AND FASTENERS YOU MAY NEED (not included)

The tools you will need for installing your shade will vary, depending on the installation surface and mounting bracket type.

Tools typically used for installation include

CAUTION: Use drywall anchors when mounting into drywall. (Not provided.) Failure to properly anchor shade could cause shade to fall possibly resulting in injury.

INSTALLATION

INSIDE MOUNT (IM)

STEP 1: MARKING THE BRACKET LOCATIONS

IMPORTANT: Before marking bracket locations, ensure that your bracket placement will not interfere with any components inside the headrail.

• Verify that your window casing has a minimum depth of 1 1⁄4″ which allows for a partially recessed headrail mount.
• If flush mount (fully recessed mount) is desired, a minimum mounting depth of 3″ is required.
• Mark approximately 1” from each jamb for bracket location.
• Mark screw locations for each end bracket, 2 holes per bracket.
• If more than two installation brackets come with your order, space additional bracket(s) evenly between the two end brackets, no more than 30” apart.

STEP 2: INSTALLING THE BRACKETS

• Pre-drill screw holes.
  • If installing brackets into wood, used supplied screws.
  • If installing into drywall, use anchors in combination with supplied screws.
• Screw in brackets at marked locations, 2 screws per bracket.
• Ensure all brackets are square with each other.

STEP 3: INSTALLING THE SHADE

• Hook the top, middle rib of the cassette valance onto all of the bracket hooks.
• Rotate the back of the cassette valance firmly upwards and toward the window until the groove at the bracket snaps into place.
  CAUTION: Be sure the brackets are properly engaged before operating the shade. Failure to do so may result in the shade falling and possible injury.

OUTSIDE MOUNT (OM)

STEP 1: MARKING THE BRACKET LOCATIONS

IMPORTANT: The brackets must be flush against a flat mounting surface. Do NOT mount brackets on curved molding

• Center the headrail over the window opening at the desired height.

• Mark screw locations for each L bracket approximately 3″ from end of cassette, 2 holes per bracket.
  Use a level to ensure all brackets will be in alignment.

• If more than two installation brackets come with your order, space additional bracket(s) evenly between the two end brackets, no more than 30″ apart.

STEP 2: INSTALLING THE BRACKETS

• Pre-drill screw holes using a 1⁄16″ drill bit, using pencil marks as a guide.
  • If installing brackets into wood,used supplied screws.
  • If installing into drywall, use anchors in combination with supplied screws.
• Screw in L brackets at marked locations, 2 screws per bracket.
• Ensure all brackets are square with each other.
• Attach cassette mounting bracket to L bracket using screws and hex nuts.— Make sure the release tab is always mounted on the bottom.

STEP 3: INSTALLING THE SHADE

• Hook the top, middle rib of the cassette valance onto all of the bracket hooks.
• Rotate the back of the cassette valance firmly upwards and toward the window until the groove at the bracket snaps into place.

CAUTION: Be sure the bracket and headrail are properly secured before operating the shade. Failure to do so may result in the shade falling and possible injury.

INSTALLATION–ADDITIONAL COMPONENTS

CONTINUOUS CORD LOOP CORD TENSION DEVICE

• Continuous Cord Loop Shades will arrive with the tension device mounted to the shade.
• Use the included screws to secure the hold-down tension device to the mounting surface, ensuring that the cord loop is taut.
• SEE WARNING LABEL ON SHADE

INSTALL THE TENSION DEVICE
IMPORTANT: Before you proceed, you must first slide the cord tensioner to the bottom of the cord loop.

• Insert a small screwdriver, punch, or awl through the screw hole at the bottom of the cord tensioner.
• Move the screw hole down to the indicator line to release the safety mechanism.
• Slide the cord tensioner down to the bottom of the cord loop.
• Attach the cord tensioner according to the instructions provided with the Universal Cord Tensioner Installation Kit.
• WARNING: It is imperative that the cord tensioner be properly secured to the wall or window frame to reduce children’s access to the cord loop. Young children can strangle in cord loops. They can also wrap cords around their necks and strangle.
• CAUTION: The shading will not operate properly unless the cord tensioner is secured. A universal Cord Tensioner Installation Kit has been included with your shading. Follow the instructions in the kit to correctly secure the cord tensioner.

HOLD-DOWN BRACKETS (optional)

• Ideal for doors, hold-down brackets prevent shade from swaying. Assemble as shown to each side of bottom rail.
• Position hold-down brackets against wall / frame, mark screw hole locations.
• Screw into marked hole locations.

OPERATION

CONTINUOUS CORD LOOP

• Pull the rear cord of the cord loop to lower the shade to the desired height.
• Pull the front cord of the cord loop to raise the shade to the desired height.

WARNING: If the tension device moves up the cord, you have not secured the tension device to the wall or window frame. You must do so for the shade to operate properly and to help protect young children from accidental strangulation.

UNINSTALL

REMOVING THE SHADE

• Fully raise the shade.
• While holding the headrail, use a flathead screwdriver to engage the release tab on the bottom of all of the installation brackets.
• Rotate the bottom of the shade away from the window, fully releasing it from the brackets.
• Uninstall remaining brackets if necessary.
  CAUTION: Hold shade firmly when removing. Failure to do so may result in the shade falling and possible injury.

CLEANING AND CARE

CLEANING PROCEDURES
All LEVOLOR Roller Shades have multiple cleaning options.
NOTICE: Avoid contact with window cleaning products. Improper cleaning may void warranty.

ADDITIONAL INFORMATION

TROUBLESHOOTING TIPS

Do not lower the shade past the ordered length. (If it is lowered beyond the limit, the tube underneath the roller will be exposed and fabric damage could occur.)

Roller Shades–Fabric/Solar/Banded

Cordless Lift Control–Cassette Valance

CANADIAN RESIDENTS ONLY

• Control operation systems vary by country. Call 1-866-937-1875 for more information.
• For all safety related inquiries, call 1-866-662-0666 or visit www.canada.ca, search “blind cords”.

WARNING STRANGULATION HAZARD
Young children can be strangled by cords. Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible..

WARNING: Keep all small parts, components and packaging away from children as they pose a potential choking hazard which may result in serious injury or death. Please reference all warning tags and labels in the instructions and on the shade.

WINDOW AND SHADE TERMINOLOGY

Thank you for purchasing LEVOLOR® Roller Shades. With proper installation, operation, and care, your new roller shade will provide years of beauty and performance. Please thoroughly review this instruction booklet before beginning installation.

MOUNTING TYPES AND WINDOW TERMINOLOGY
If the installation brackets are mounted correctly, the rest of the installation process follows easily. To prepare for this important first step, review the mounting types and basic window terminology illustrated below.

INSTALLATION OVERVIEW

• Leaving the shade rolled up completely will ease installation.
• Confirm that the headrail and shade are the proper width and length.
• If installing several sets of shades, be sure to match them with the appropriate window.
• Check the installation surface to ensure that you have suitable fasteners and tools.
• Lay out and organize all parts and components.

Installation Brackets

Installation Brackets

Your order will include the correct number of installation brackets for your shade width, as shown in the table below
Shade Width (inches)| Number of Brackets per Shade
Up to 36| 2
36 to 54| 3
54 to 72| 4
72 to 108| 5
2-on-1 Headrail Shades| 2 additional brackets provided

GETTING STARTED

COMPONENTS INCLUDED IN THE BOX

• Shade
• Mounting Brackets
• Installation Hardware

Optional items will be included, if selected at time of shade order.

GETTING STARTED

TOOLS AND FASTENERS YOU MAY NEED (not included)
The tools you will need for installing your shade will vary, depending on the installation surface and mounting bracket type.

Tools typically used for installation include

CAUTION: Use drywall anchors when mounting into drywall. (Not provided.) Failure to properly anchor shade could cause shade to fall possibly resulting in injury.

INSTALLATION

INSIDE MOUNT (IM)

STEP 1: MARKING THE BRACKET LOCATIONS
IMPORTANT: Before marking bracket locations, ensure that your bracket placement will not interfere with any components inside the headrail.

• Verify that your window casing has a minimum depth of 1 3⁄4″ which allows for a partially recessed headrail mount.
• If flush mount (fully recessed mount) is desired, a minimum mounting depth of 3″ is required.
• Mark approximately 1″ from each jamb for bracket location.
• Mark screw locations for each end bracket, 2 holes per bracket.
• If more than two installation brackets come with your order, space additional bracket(s) evenly between the two end brackets, no more than 30″ apart.

STEP 2: INSTALLING THE BRACKETS

• Pre-drill screw holes.
  If installing brackets into wood, used supplied screws.
  If installing into drywall, use anchors in combination with supplied screws.

• Screw in brackets at marked locations, 2 screws per bracket.

• Ensure all brackets are square with each other.

STEP 3: INSTALLING THE SHADE

• Hook the top, middle rib of the cassette valance onto all of the bracket hooks.
• Rotate the back of the cassette valance firmly upwards and toward the window until the groove at the bracket snaps into place.
  CAUTION: Be sure the brackets are properly engaged before operating the shade. Failure to do so may result in the shade falling and possible injury.

OUTSIDE MOUNT (OM)

STEP 1: MARKING THE BRACKET LOCATIONS

IMPORTANT: The brackets must be flush against a flat mounting surface. Do NOT mount brackets on curved molding.

• Center the shade over the window opening at the desired height.

• Mark screw locations for each L bracket approximately 3″ from end of cassette, 2 holes per bracket.
  Use a level to ensure all brackets are aligned.

• If more than two installation brackets come with your order, space additional bracket(s) evenly between the two end brackets, no more than 30″ apart.

STEP 2: INSTALLING THE BRACKETS

• Pre-drill screw holes using a 1⁄16″ drill bit, using pencil marks as a guide.
  If installing brackets into wood, use supplied screws.
  If installing into drywall, use anchors in combination with supplied screws.

• Screw in L brackets at marked locations, 2 screws per bracket.

• Ensure all L brackets are square with each other.

• Attach cassette mounting bracket to L bracket using screws and hex nuts.
  Make sure the release tab is always mounted on the bottom.

STEP 3: INSTALLING THE SHADE

• Hook the top, middle rib of the cassette valance onto all of the bracket hooks.
• Rotate the back of the cassette valance firmly upwards and toward the window until the groove at the bracket snaps into place.

CAUTION: Be sure the bracket and headrail are properly secured before operating the shade. Failure to do so may result in the shade falling and possible injury.

INSTALLATION–ADDITIONAL COMPONENTS

INSTALL BOTTOM RAIL OPERATING HANDLE(S)

• For Fabric/Solar shades, insert front lip of the optional bottom rail handle into the top of the bottom rail of the shade. The handle will snap into place.
  For Fabric/Solar shades, optional Tassel will come attached to shade.
  For Banded shades, Bottom Rail Handle will come attached to shade.

HOLD-DOWN BRACKETS (optional)

• Ideal for doors, hold-down brackets prevent shade from swaying. Assemble as shown to each side of bottom rail.
• Position hold-down brackets against wall / frame, mark screw hole locations.
• Screw into marked hole locations.

OPERATION

CORDLESS

• Pull the bottom rail of shade towards bottom of window frame to the desired height.
  Optional bottom rail handles may be used.

• Gently pull bottom rail and release shade, and it will raise fully unless stopped at a new height.

UNINSTALL

REMOVING THE SHADE

• Fully raise the shade.
• Press in the clear tab on the shade bracket.
• Release one edge of the headrail from the bracket.
• Rotate the shade to release the other edge of the headrail from the bracket.
• Uninstall remaining brackets if necessary.
• CAUTION: Hold shade firmly when removing. Failure to do so may result ! in the shade falling and possible injury.

CLEANING AND CARE

CLEANING PROCEDURES

All LEVOLOR Roller Shades have multiple cleaning options.

NOTICE: Avoid contact with window cleaning products. Improper cleaning may void warranty.

ADDITIONAL INFORMATION

TROUBLESHOOTING TIPS
Do not lower the shade past the ordered length. (If it is lowered beyond the limit, the tube underneath the roller will be exposed and fabric damage could occur.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>