noyafa NF-806 Lan Cable Wire Tracker Instruction Manual

noyafa NF-806 Lan Cable Wire Tracker

interfaces and functions
Find wire on all types of connected operating
Ethernet switch/Router/PC terminal(<48V)

OVERVIEW

Telephone cable tracing function

1. Directly insert telephone wire with RJ 11 plug into the RJ11 socket of emitter;
   (Note: Never put energized telephone cable into RJ45 port, in fear of burnout to the tester)

2. Push DIP switch of emitter to position of “SCAN” then wire finding indicator “STATUS” flashes, which means the emitter works normally;

3. Press the inching button, use the probe of receiver to find target wire at the other end;

4. During testing, function switchover button can be pressed for switchover of dual-tone.

Rapidly find the target wire from among plenty of telephone wires

Network cable tracing function

1. Directly insert network cable into the RJ45 port of emitter;
2. Push DIP switch of emitter to position of “SCAN” then wire finding indicator “STATUS” flashes which means normal work of emitter;
3. Press the inching button, use the probe of receiver to find target wire at the other end;
4. During testing, function switchover button can be pressed for switchover of dual-tone.

Rapidly find the target wire from among plenty of network wires

Electric wire tracing function

1. Directly insert RJ11 of crocodile clip into RJ11 port of emitter, connect telephone line with the clamp.
2. Push DIP switch of emitter to position of “SCAN” then wire finding indicator “STATUS” flashes, which means normal work of emitter.
3. Press the inching button, use the probe of receiver to find target wire at the other end.
4. During testing, function switchover button can be pressed for switchover of dual-tone.

Rapidly find the target wire from among plenty of network wires

CASE

Note: The equipment is prohibited to be used on heavy-current wires

How to find the wire from among so many wires?
It is so slow by using a multimeter.

Network wire Collation function

1. Insert the two ends of the network cable into the RJ45 ports of emitter and receiver.
2. Push function switchover button on emitter to the position of “TEST” testing indicator “VERIFY” flashes meaning normal work of emitter.
3. According to 18 indicators, judge the characteristics of short-circuit, breaking circuit, open circuit and crossing.
4. During testing, function switchover button can be pressed for switchover of fast and slow levels.

Network wire sequence collation

CASE

Note: The equipment is prohibited to be used on heavy-current wires

Support direct wire collation of operating switch

Replace the above tester in cabling
It can take place of cable tester

Other function

Open or Short circuit test Function
Please turn the button to the “TEST” position and press the “SWITCH” button for 2 seconds of the Emitter, then the “VERIFY ” keep lighting and clamp the clips to the two side of the wire. If the condition is short, the “STATUS” light of the emitter will turns red. The impedance of the wire can be showed by the degree of status light, the more bright light the less impedance.

DC level testing function

Push DIP switch on emitter to position of ” SCAN”, press function switchover button on emitter for 2 seconds, ” STATUS” indicator will turn off and ” VERIFY” indicator flashes, insert the crystal plug of crocodile clamp into RJ11, clamp the two ends of cable with crocodile clamps, in case that ” STATUS” indicator lights up in red, it means the end clamped by red clamp is positive pole, in case that ” STATUS” indicator lights up in green, it means the end clamped by red clamp is negative pole, electric level can be judged by brightness of the status indicators; the lighter the indicator, the higher the level is; the darker, the lower.

Low voltaage alarm function
Push DIP switch on emitter to position of “SCAN”, if the that battery level is lower than 6.0V, “STATUS” and “VERIFY” indicators will light up at the same time, it indicates to have new battery.

Earphone function

In noisy environment, earphone can be used to prevent interference from the outside.

Volume adjusting function
While tracing cable, volume can be adjusted for moderate level of sound.

Spotlight function
You can easily work as usual with backlight at night and in dark.

Energy-saving
Inching switch can automatically delay power-off.
The continuous lifespan of battery is over 50 hours.

Accessories

Applicable users
Telecom bureau/net bar/telecom engineering companies / network engineering companies/power supply/army and other departments requiring wire.

Applicable scope
Wire engineering of telecom, network and regular maintenance work; network line engineering of computer; other wire engineering and maintenance.

Specification of product

Appearance dimension

| Emitter| 126X49X34,mm
Receiver| 175X42X27,mm
Whole set| 270X 165X45,mm

Weight

| Emitter| 0.060kg
Receiver| 0.072kg
Whole set| 0.420kg

The list of package

Diagram of series products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>