Metalux 2WPLD2035C 2 Foot Linear LED Wrap Light Instruction Manual

: June 17, 2024
: METALUX

Table of Contents

Metalux 2WPLD2035C 2 Foot Linear LED Wrap Light
Product Information
Product Usage Instructions
FAQ
PACKAGING CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
WARRANTY
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Metalux 2WPLD2035C 2 Foot Linear LED Wrap Light

Product Information

Specifications

Series: WPLD
Packaging Contents:
- Fixture housing
- Lens
- Wire connectors (3)

Product Usage Instructions

Installation Instructions

Turn off the power at the main fuse/breaker box. Carefully open the carton and remove the fixture.
Remove the lens from the luminaire by pulling up from the edge of the lens near the endcap.
Locate wires in the outlet box. Connect fixture wires to power supply wires (white to white, black to black, green to green) using wire nuts.
Push all wires and wire nuts inside the junction box.
Align fixture mounting slots with J Box mounting holes. Secure the fixture to J Box using 8-32 x 25 mm mounting screws.
Attach the lens by aligning the lens groove with the edge of the channel. Ensure the lens groove is secured along the entire length on both sides. Remove the protective film from the lens.
Turn on the breaker and use the wall switch to verify that the light turns on.

FAQ

Q: Can I use this fixture outdoors?
A: This fixture is suitable for indoor use only.

PACKAGING CONTENTS

Metalux-2WPLD2035C-2-Foot-Linear-LED-Wrap-Light-FIG-1

ITEMS REQUIRED
(Purchase separately)

Phillips screwdriver
Flat head screwdriver
Pliers
Safety glasses
Ladder
Hammer

Note: This product is not intended for continuous row applications. Suspension kits are sold separately.

IMPORTANT SAFETY INSTRUCTIONS

When using the product, basic precautions should always be followed, including the following:

Read and follow these instructions.
Heed all warnings, including the below warnings AND those included on the product.
Save these instructions and warnings.

WARNING

Risk of fire/electric shock.
Ground fixture to avoid potential electric shock.
Turn off the power at the fuse or circuit breaker box before installation and maintenance.
Edges may be cut. Handle with care.

CAUTION

Connect model: 4WPLD3140R9, 4WPLD2340R or 2WPLD2040R fixture to a 120-volt, 60 Hz power source. Any other connection voids the warranty.
Connect model: 4WPLD4035C, 4WPLD4040C, 2WPLD2035C fixture to a 120 or 277-volt, 60 Hz power source. Any other connection voids the warranty
Fixture should be installed by persons with wiring experience or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be under the National Electrical Code and local building codes.

INSTALLATION INSTRUCTIONS

Turn off the power at the main fuse/breaker box.
Carefully open the carton, and remove the fixture from the carton.
Remove from the packaging and remove the lens from the luminaire (Fig. 1) by pulling up from the edge of the lens near the endcap.
The LED wrap fixture is compatible out of the box for installation with a 4” surface J Box with 3.5” mounting hole spacing. If using a 3” J Box with 2.75” mounting hole spacing use alternate mounting hole slots in the fixture by removing knockouts. Be sure to properly support the fixture before removing knockouts to help prevent deforming the fixture.
Remove appropriate knockouts for mounting.
To remove simply place a flathead screwdriver on the knockout and strike it sharply with a hammer. The slug may then be removed with pliers (Fig. 2).
Locate wires in an outlet box. Connect all fixture wires to power supply wires: White to white, black to black, and green to green with wire nuts (D) (Fig. 3).
After Connections push all wires and wire nuts inside the junction box (Fig. 4).
Align fixture mounting slots with J Box mounting holes. USE 8-32 x 25 mm mounting screws (C) to secure the fixture to J Box (Fig. 5).
Note: To ensure that once installed to the field junction box, there shall be no visible gaps between the ceiling surface at the outlet box and the luminaire housing.
Attach the lens (Fig. 6) by aligning the lens groove with an edge of the channel. Ensure the lens groove is secured along the entire length of the lens on both sides.
Remove the protective film from the lens.
Turn the breaker on. Use a wall switch to verify light turns on.

DIMMING INSTALLATION INSTRUCTIONS

For a fixture containing (1) 120V Driver.
Wire per dimmer manufacturer’s instructions. See www.cooperlighting.com for a listing of dimmers that are compatible with the WLD series product.
For a fixture containing (1) 120/277V Driver.
Combine the positive lead from the dimmer with the positive lead (violet) connected to the dimming port (DIM +) of the driver.
Combine the negative lead from the dimmer with the gray negative lead connected to the (DIM -) dimming port of the driver using the wire termination that is fastened to the end of the gray dimming lead.

SUSPENSION INSTRUCTIONS

The product can be suspended. For a list of manufacturer suspension options that are compatible with the WPLD series product visit www.cooperlighting.com.

ENERGY STAR

ENERGY STAR® is sponsored by the U.S. Environmental
Protection Agency & U.S. Department of Energy.
Visit www.energystar.gov to learn more.

WARRANTY

5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN PLACE OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Cooper Lighting Solutions (“CLS”) warrants to customers that, for five years from the date of purchase, CLS products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of the date of original purchase is acceptable to CLS. This is required before warranty performance shall be rendered. This warranty does not apply to CLS products that have been altered or repaired that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS that have been supplied, installed, and/or used in conjunction with CLS products. Damage to the product caused by replacement bulbs or corrosion or discolouration of brass components are not covered by this warranty.
LIMITATION OF LIABILITY
IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR LOST PROFITS; NOR SHALL THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

To obtain warranty service, please contact CLS at 1-800-334-6871, press option 2 for Customer Service, or via e-mail at ConsumerProducts@cooperlighting.com and include the following information:

Name, address and telephone number
Date and place of purchase
Catalogue and quantity purchase
Detailed description of the problem

All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused. CLS is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

Reproductions of this document without prior written approval of CLS are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@cooperlighting.com Printed in China