ergotron 45-354-026 LX Wall Keyboard Arm User Guide
- June 4, 2024
- ERGOTRON
Table of Contents
45-354-026 LX Wall Keyboard Arm
User Guide
45-354-026 LX Wall Keyboard Arm
Safety
WARNING: Ensure that the wall structure is capable of supporting four
times the total weight of mounted equipment. Mounting to wall surfaces that do
not meet this criterion may result in an unstable, unsafe condition which
could lead to personal injury and/or property damage. Consult a construction
professional if you have any doubt about what this means in regard to your
particular application.
Optional locking feature (customer-supplied lock) NOTE: Product movements
and spring adjustments may not work until mounted and all equipment has been
attached.
Tools Needed
| WOOD
---|---
| CONCRETE
Mounting Height Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that
accommodates user heights of 5’0″-6’4″ (152-193cm) when set up for standing
and user heights of 5’0”-6’4” (152-193cm) when set up for sitting. If user
heights are diff event than this, you should change the mounting height to
accommodate user heights. (Change the mounting height by one inch for every
one-inch diff erence in user heights). Mounting height assumes there is a 6”
(152 mm) distance between the center of your monitor mounting holes and the
top of the screen. If your distance is smaller, you should increase the
mounting height accordingly, if your distance is larger, you should decrease
your mounting height accordingly.
Determine mounting location:
Front view with arm pushed back against the wall.
Top view showing a range of motion when pulled out from the wall.
CAUTION: Make sure the wall mount bracket is level, fl used, and snug to
the wall surface. DO NOT OVERTIGHTEN THE BOLTS. WOOD STUD MOUNTING CONCRETE
ERGOTRON PRODUCT WOOD STUD MOUNTING CONCRETE
WARNING: Mounting holes must be at least 3-1/8” (80mm) deep and must be
located within solid concrete, not mortar or covering material. If you drill
into an area of concrete that is not solid, reposition mounting holes until
both anchors can be fully inserted into solid concrete!
WARNING: Anchors that are not fully set in solid concrete will not
support the applied load resulting in an unstable, unsafe condition that could
lead to personal injury and/or property damage. Consult a construction
professional if you have any doubt about what this means in regard to your
particular situation.
ERGOTRON PRODUCT; Wall Track and Brackets sold separately.
Important! You will need to adjust this product after installation
is complete. Make sure all your equipment is properly installed on the product
before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are
too easy or diffi cult or if the product does not stay in desired positions,
follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice
a diff erence. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat
these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to
your equipment. Increase Lift Strength If the mounted weight is too heavy or
this product does not stay up when raised, then you’ll need to increase Lift
Strength:
Decrease Lift Strength If the mounted weight is too light or this product does
not stay down when lowered, then you’ll need to decrease Lift Strength:
Arm Swing – Side-to-side
CAUTION: DO NOT remove the screw. Removing screws may cause damage to
equipment. Increase Friction If this product moves too easily, then you’ll
need to increase friction:
Decrease Friction If this product is too diffi cult to move, then you’ll need to
decrease friction:
How to remove this tilting feature: Yup, that’s it. Really.
Now your LX Arm is ready for however you work best. Learn more about ergonomic
computer use at:
www.ergotron.com/ergonomics
Safety
WARNING! Stored Energy Hazard: The arm mechanism is under tension and
will move up rapidly, on its own, as soon as the attached equipment is
removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result
in serious personal injury and/or equipment damage!
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure the mounting surface is strong enough to handle
mounted products and equipment.
Caution: Leave enough slack in the cable to allow a full range of motion.
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury. Weight Capacity:
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer service, reference the serial number.
www.ergotron.com
I USA: 1-800-888-8458
I Europe: +31 (0)33-45 45 600
I China: 400-120-3051
I Japan: japansupport@ergotron.com
© 2014 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design nd/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
888-45-047-W-05 rev. W • 06/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>