MADSTAD ENGINEERING Can Am Spyder Adjustable Windshield Mount Instruction Manual

MADSTAD ENGINEERING Can Am Spyder Adjustable Windshield Mount

Product Information

Specifications:

• Adjustable windshield brackets
• Material: Black aluminium adapter plate
• Mounting screws: M6 x 12, M5 x 20 truss screws
• Includes washers and lock nuts
• Tools required: 4 mm Allen wrench, 10 mm wrench

Product Usage Instructions

Bracket Installation:

1. Attach the Robo Knob brackets to the MadStad adapter plate using the provided screws, washers, and lock nuts.
2. Ensure that the knobs on the brackets face each other with the knob sides up.
3. Attach the adapter plate to the fairing in place of the stock shield using the original factory windshield screws and washers.

Adjusting the RoboKnob Brackets:

1. Use the knob screws to release the brackets for windshield adjustment.
2. Always tighten the knob screws securely before riding and avoid adjusting while riding.
3. Do not set the windshield in a way that may cause interference with handlebars or hand guards.
4. To adjust the windshield position, come to a complete stop, loosen knob screws, make adjustments, and re-tighten before riding again.

Pivot Screws:
The MadStad mount includes pivot screws for fine adjustments. Use the provided tools to adjust the tightness or position of pivot screws for optimal windshield tilt.

Frequently Asked Questions (FAQ):

• Q: Can I use my factory windshield with these brackets?
  A: No, the factory windshield is not adaptable for use with these brackets. You will need to replace it with the provided adapter plate.

• Q: How do I prevent scratching on the back of the shield?
  A: Avoid tilting the shield fully backward to prevent contact with the top edge of the brackets. Check for contact before finalizing adjustments.

Please read this entire manual before proceeding with installation.

What is in the box

• (1) Set of preassembled MadStad adjustable windshield brackets
• (1) Black aluminum adapter plate
• (4) M6 x 12 mounting screws
• (4) M6 flat washers
• (4) M6 lock nuts
• (4) M5 x 20 truss screws
• (4) M5 soft rubber washers
• (4) M5 Black plastic flat washers

Tools Needed

• 4 mm Allen wrench (hex key)
• 10 mm wrench (open-end, box, or adjustable crescent)

You will need to remove your factory windshield; it is not adaptable for use with these brackets.

Bracket Installation

Your Robo Knob brackets attach to the MadStad adapter plate as shown on page 3. Use the (4) M6 x 12 screws with M6 flat metal washers and M6 lock nuts as shown in the diagram below.

The knobs on the brackets go to the insides (facing each other) with the knob sides up. When both brackets are installed, it should look like the diagram below:

Your brackets may be slightly different, this is for orientation illustration.

The adapter plate then attaches to the fairing in place of the stock shield. You may have to wiggle it around a bit to get all the holes lined up, then screw it in with the original factory windshield screws and washers.

Windshield Installation

1. Pre-install the Truss screws & washers into the windshield holes as shown in the image below.
2. Once all four of the screws are in place, gently guide the screws into the Well Nuts in the brackets until all four are set.
3. Hand-tighten the Truss screws until they swell up behind the bracket and are firmly holding the windshield.

Adjusting the RoboKnob Brackets

The knob screws release the brackets allowing the windshield to slide and tilt. These knob screws must always be tightened securely before riding. DO NOT attempt to adjust the brackets while riding! You must come to a complete stop before making adjustments. Also make sure that you do not set the windshield in such a way that causes your handlebars or hand guards (if installed) to hit the windshield when turning, or before reaching full lock.

To make adjustments, loosen the knobs for 1-2 turns and set the windshield so the top edge is at about your chin level as you look straight ahead while seated on the bike. Set the angle at approximately 60 degrees. (Use the angle guide on the back page of this manual as a guide.) Tighten the knobs and go for a ride to see if you now have smooth airflow over and around your helmet. Do this on a calm day if at all possible; windy days make it hard to judge the airflow. Don’t ever try to adjust the mount while in motion!

WARNING:
If you tilt the shield fully backward, it may make contact with the top edge of the brackets. This could scratch the back of your shield, so please check to make sure there is no contact.
To try a different windshield position, bring the motorcycle to a complete stop and out of traffic. Loosen the two knob screws and tilt the windshield forward or back 2-3 degrees or so, and/or adjust it up or down if necessary. Re-tighten the knobs and go for another ride.

Continue experimenting with different positions at different speeds until you find a combination of height and rake angle that eliminates buffeting and gives a smoother ride. You may have more than one favourite position, for example, shield tilted forward on cooler days, and shield tilted back on hot days to let more air into your body.

PIVOT SCREWS

The MadStad mount has a pivot screw on each set of brackets, located near the center of the bottom bracket. A nylon lock nut keeps the screw snugly in place, yet allows the brackets to slide back and forth. It is adjusted at the factory to have a minimum of play yet still allow the brackets to move. The upper pivot hole gives maximum rearward tilt, and the lower pivot hole moves the tilt range 5 degrees forward. The lower pivot hole also brings the shield a bit closer to the bike. If for some reason you wish to adjust the tightness of this pivot screw or move it to an alternate pivot position, use the 4mm Allen wrench provided, along with a 10mm socket or wrench to adjust. If you tighten the lock nut completely you will not be able to slide the brackets.

Notes on Windshield Angle

Most windshields work best when set at a 55-60 degree angle. We have provided an angle guide on the back page of this manual so that you can check and see if your shield is set somewhere in this range. To check your shield angle, your bike should be in an upright position either on a centre stand or held up by a helper. Set the spine (folded edge) of the manual against the front of the shield. If the large arrow marked 60° is pointing straight up, then your shield is at a 60-degree angle. (See diagram on Page 5.) A little farther back and your angle would be somewhere between 55 and 60 degrees. Anywhere in this range is fine for your initial test ride. On some bikes a more vertical angle works better, so don’t be afraid to experiment later if tilting the shield back doesn’t seem to be ideal.

Disclaimer

Neither MadStad Engineering nor its owners shall be liable for any damages, consequential or inconsequential, resulting from the use of our products. Installation of any of our products constitutes acceptance of these terms.

It is the responsibility of the user to make sure all fasteners are tightened securely, the windshield is mounted properly and the adjustment knobs are tightened snugly before putting the motorcycle in motion. MadStad systems ARE NOT intended to be adjusted while the vehicle is in motion; you must pull over out of the way of traffic and come to a complete stop before making any changes. The user must never place the windshield in such a position as to interfere with the safe and complete movement of the handlebars and controls.

Returns and Warranty

MadStad adjustable brackets carry a lifetime warranty against manufacturing defects. This does not include cosmetic issues nor any parts that inherently wear out or degrade over time such as rubber and plastic parts. Windshields, deflectors, and other similar plastic parts are warrantied for 1 year against manufacturing defects, not against cosmetic issues or issues related to normal wear and tear. Please visit our website for further details.

MadStad Engineering, Inc.

• 1451 E. Jefferson St. Brooksville, FL 34601
• Phone: 352-848-3646
• Web Site: http://www.madstad.com.
• Email: support@madstad.com.

Thank you for your support, and ride safely!

Documents / Resources

| MADSTAD ENGINEERING Can Am Spyder Adjustable Windshield Mount [pdf] Instruction Manual
Can Am Spyder Adjustable Windshield Mount, Spyder Adjustable Windshield Mount, Adjustable Windshield Mount, Windshield Mount, Mount
---|---

References

• Adjustable motorcycle windshield systems | motorcycle windscreen | Madstad
• Adjustable motorcycle windshield systems | motorcycle windscreen | Madstad

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>