Supreme ZG140 Hydro Mag Recirculating Water Pumps Instruction Manual

Supreme ZG140 Hydro Mag Recirculating Water Pumps

Specifications

• Model: 120VAC/60HZ Magnetic-Drive 24 / 36 and 230VAC/50HZ 8700 LPH Pumps
• Available Sizes: 4 oz., 32 oz., 128 oz.
• Parts List:
  • Impeller Assembly 24 Type A
  • Impeller Assembly 36 Type A
  • Impeller Assembly 24 Type B
  • Impeller Assembly 36 Type B
  • Impeller Assembly 8700 LPH Type B
  • Volute, Flap, O-Ring
  • Pre-filter Screen
  • Magnet/Impeller Assembly (includes all ceramic bearings)
  • Volute with Flap and O-Ring
  • Pre-filter
• Model 24, Type A and B:
  • Outlet Size   NPT: 1MPT
  • Inlet Size   NPT: 1FPT
  • Wattage: 237
  • Amps: 2.2
• Model 36, Type A and B:
  • Outlet Size NPT: 1MPT
  • Inlet Size NPT: 1FPT
  • Wattage: 369
  • Amps: 3.3
• Model 8700 LPH:
  • Inlet Size NPT: 1MPT
  • Outlet Size NPT: 1MPT
  • Wattage: 230
  • Amps: 1.02

Product Usage Instructions

1. Disconnect Power: Turn off the power to the pump.
2. Remove Pump: Take the pump out of the water.
3. Position Pump: Place the pump with the volute inlet facing upwards.
4. Pour Pumpguard: Fill the volute inlet with the Pumpguard until full.
5. Soak: Allow the pump to soak for 2 to 3 minutes.
6. Rinse: Thoroughly rinse the pump with clean water.
7. Reinstall: Put the pump back into service.

Frequently Asked Questions (FAQ)

Q: How often should I use PumpguardTM for maintenance?

• A: It is recommended to use PumpguardTM regularly to keep water pumps running like new.
• The frequency of use may depend on the specific conditions and usage of your pump.

Q: Can I use PumpguardTM on any type of water pump?

• A: PumpguardTM is designed for pump maintenance and can be used on various types of water pumps.
• However, it is always advisable to refer to the specific pump’s manual for compatibility and instructions.

Q: Is PumpguardTM safe for the environment?

• A: PumpguardTM is formulated to be safe for pumps and aquatic environments when used as directed.
• It is important to follow the usage instructions provided to ensure proper application and safety.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To guard against injury, basic safety precautions should be observed, including the following:

• a) READ AND FOLLOW AlI SAFETY INSTRUCTIONS
• b) DANGER – To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment.
• For each of the following situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance:

1. If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source. (Immersible equipment only)
2. Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.
3. Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner.
4. When used with an aquarium, to avoid the possibility of the appliance plug or receptacle getting wet, position the aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A “drip loop shown in the figure below, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The “drip loop” is that part of the cord below the level of the receptacle, or the connector in an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then, unplug and examine for the presence of water in the receptacle.

• c) Close supervision is necessary when any appliance is used by or near children.
• d) To avoid injury, do not contact moving parts or not parts.
• e) Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank the cord to pull the plug from the outlet. Grasp the plug and pull to disconnect.
• f) Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsate condition.
• g) Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.
• h) Make sure an appliance mounted on a tank is securely installed before operating it.
• I ) Read and observe all the important notices on the appliance.
• j If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for fewer amperes or watts than the appliance rating may overheat.
• Care should be taken to arrange the cord so that it will not be tripped over or pulled.

INSTALLATION INSTRUCTIONS

• The pump can be used submersed to a maximum depth of 36″ when used in aquarium applications; no depth requirements for pond use.
• When used with inline piping note the following: Centrifugal pumps cannot pull water from a lower level. To start, the pump must be below water level and filled with water.
• Unless the air can escape from the outlet, the pump will not start. Do not use glues or solvents to connect

CAUTION

• The pump is intended to pump water only. It cannot be used to pump oil, solvents, or gasoline.
• Although the pump will continue to run if there is no water, after 30 minutes damage may occur if allowed to run dry.

GROUNDING INSTRUCTIONS

• This appliance should be grounded to minimize the possibility of electric shock.
• This appliance is equipped with an electric cord having an equipment grounding conductor and a grounding type plug (Some models).
• The plug must be plugged into an outlet that is installed and grounded under all appropriate codes and ordinances.
• For 120VAC models: This appliance is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in (A) below.
• A temporary adapter which looks like the adapter illustrated in (B and C) below may be used to connect this plug to a two-pole receptacle as shown in (B) if a grounded outlet is not available.
• The temporary adapter should be used only until a grounded outlet can be installed by a qualitied electrician. Ine green-colored rigid ear (lug, and the like) extending from the adapter must be fastened to a permanent ground such as a grounded outlet box.

SERVICE AND MAINTENANCE

• The pump volute should occasionally be removed to clean and inspect the impeller assembly. The impeller is the only serviceable item and can be pulled out of the body.
• Do not take the impeller apart except for cleaning when used in salt water or hard water applications; see below. If it is worn or broken the entire impeller assembly should be replaced.
• This will restore the pump to its original capacity. Pumps taken out of service for an extended period with fluid inside run the risk of forming a crust which may prevent subsequent starting. Saltwater should be flushed out with fresh water.
• Always check the cord for sharp bends which can cause premature cracking.
• Do not use a power cord to lift or move the pump. Other than Impeller maintenance, this appliance has no user-serviceable parts. Magnet impeller assembly must be routinely cleaned to remove accumulations of scale or calcium.
• This procedure should be done at least once every three months – or more often if the water conditions require it. Saltwater and hard water environments require more frequent cleaning.
• Pondmaster® PUMPGUARD™ WATER PUMP MAINTENANCE SOLUTION (sold separately) will instantly loosen scale, lime, rust, and other detritus from moving parts and the impeller chamber.
• Most build-up can be removed without disassembling the pump. See instructions on the next.

IMPORTANT: FOR PUMPS USED IN SALTWATER OR HARD WATER

• Magnet impeller assembly must be routinely removed for cleaning in white vinegar to remove accumulations of scale or calcium.
• This procedure should be done at least once every three months – or more often if the water conditions require it. Disassemble the magnet from the impeller by pulling them apart (it will take a strong pull). One end cap will come off.
• To clean the calcium scale off the shaft and bearing inside of the magnet, soak it in white vinegar for a few hours and scrape it off. For faster results use a PUMPGUARD cleaning solution.
• Reassemble the magnet/impeller assembly and use caution when reinserting the magnet is very strong and will pull in quickly.
• Pumpguard™ an easy maintenance solution that will keep water pumps running like new when used regularly.

PUMPGUARD™ pump maintenance solution is available in three sizes:

• 4 oz. —– lmpellerNolute Treatment ———Item # 03905
• 32 oz. — Soak/Dunk & Impeller Treatment –Item # 03907
• 128oz. –Commercial Size———————— Item # 03909

PUMP GUARD INSTRUCTIONS

1. Disconnect power to pump
2. Remove the pump from the water.
3. Position pump with volute inlet facing upwards
4. Pour the Pumpguard into the volute inlet until full.
5. Allow to soak for 2 to 3 minutes.
6. Thoroughly rinse with clean water.
7. Place pump back into service

PARTS LIST AND SPECIFICATIONS FOR 120VAC/60HZ MAGNETIC-DRIVE 24 / 36 AND 230 VAC/S0HZ 8700 LPH PUMPS

1 ½” INSIDE DIAMETER IS THE MINIMUM TUBING SIZE THAT SHOULD BE USED FOR MAXIMUM FLOW

LIMITED WARRANTY

• Danner pumps are warranted against failure due to defects in materials and/or workmanship as follows: Pump body and volute within five years, impeller and included accessories within one year of original purchase.
• This warranty does not cover any replaceable filtering material supplied with the pump or filter as it is considered expendable. This warranty covers defects occurring under normal use.
• The warranty and remedies set forth herein are conditional upon proper installation, use, maintenance, storage, and conformance with the applicable use. It will be based on Danner Mfg. discretion as to whether the defects are of manufacturing origin.
• For warranty repair, return only the part that is defective to our factory. Please include a dated proof of purchase and $10.00 for postage and handling. Any damages due to improper installation are not covered by this warranty.
• This warranty does not apply to appearance or aftermarket accessory items.
• This warranty does not include damage due to handling, transportation, unpacking, setup, installation, repair, or replacement of parts supplied by any other than Danner Mfg. improper maintenance, modification, or repairs by the purchaser; abuse, misuse, neglect, accident, fire, flood, or other acts of God. Any oral statements about this product made by the seller, the manufacturer, their representatives, or any other parties do not constitute warranties shall not be relied upon by the user, and are not part of this contract. Neither the seller nor the manufacturer shall be liable for any injury, loss, or damages, direct, incidental, or consequential, including but not limited to incidental or consequential damage for lost profits, lost sales, injury, and inability to Use the product and the user agrees that no other remedy is available. Before using, the user shall determine the suitability of the product for their intended use and the user shall assume all risk liability whatsoever in connection therewith.
• TO VALIDATE THIS WARRANTY, KEEP YOUR PROOF OF PURCHASE (COPY OF SALES RECEIPT FROM A CERTIFIED PONDMASTER OR SUPREME DEALER).
• The warranty covers the repair or prorated replacement of the Danner Mfg. products. Danner Mfg. denies all liability for any other loss including but not limited to loss of equipment, income, livestock, vegetation, or personal injury.
• THE FOLLOWING VOIDS WARRANTY: LINE CORD OR PLUG IS ALTERED OR CUT, PRODUCT LABELS ARE DEFACED OR REMOVED.
• PRODUCT IS IMPROPERLY INSTALLED OR MAINTAINED BY THE USER OR THEIR AGENT. PRODUCT IS ABUSED, MISUSED, OR DAMAGED BY THE USER OR THEIR AGENT.
• PRODUCT IS NOT REMOVED FROM SERVICE AND DRIED DURING FREEZING CONDITIONS.
• WARNING! PONDS CAN BE DANGEROUS TO SMALL CHILDREN.
• NEVER LEAVE CHILDREN UNSUPERVISED NEAR A POND!
• DANNER MFG. INC. 160 OVAL DRIVE, ISLANDIA, NEW YORK 11749 VISIT OUR WEB SITE: WWW.DANNERMFG.COM

Documents / Resources

| Supreme ZG140 Hydro Mag Recirculating Water Pumps [pdf] Instruction Manual
ZG140 Hydro Mag Recirculating Water Pumps, ZG140, Hydro Mag Recirculating Water Pumps, Mag Recirculating Water Pumps, Recirculating Water Pumps, Water Pumps
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>