Qbic EP-0400 Desk Booking Device User Guide
- June 15, 2024
- Qbic
Table of Contents
Quick Start Guide
This guide is designed to help you quickly set up the EP-0400.
EP-0400
ePaper
EP-0400 Desk Booking Device
Product Overview
1. Display
2. LED
3. Button 1
4. Button 2| 5. Button 3
6. Reset
7. Bracket
8. Battery Cover
---|---
Installation
-
Install Battery
STEP 1
Install CR2450 coin batteries.
(up to 4 pcs)| STEP 2
Fix M3 screws to battery cover.
---|---
| -
Tape Mount**
STEP 1
Attach tape on the back of bracket.| STEP 2
Fix the bracket with tape on the surface.| STEP 3*
Fasten M3 screw3 to secure the bracket and ePaper.
---|---|---
| | -
Surface Mount**
STEP 1
Install bracket on surface.
(wood/ concrete)
(screws not included)| STEP 2
Mount the ePaper on the bracket.| STEP 3*
Fasten M3 screw3 to secure the bracket and ePaper.
---|---|---
| |
NOTICE:
It is recommended to secure with M3 screw. The suggested length of the M3
screw is the thickness of mounting bracket plus 8mm(screw not included).
Please ensure the mounting surface is clean and smooth before using the tape.
M3 screw Torque<2 kgf-cm
Recommended Installation Height: <2M
CARE AND WARNING
WARNING :
Changes or modifications to this unit not expressly approved by the party
responsible for compliance will void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
8 digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.|f this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
- May not cause harmful interference.
- Must accept any interference received, including interference that may cause undesired operation.
Correct disposal of this product :
This marking indicates that this product should not be disposed with other
household wastes
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, use the return and collection
systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
FCC & CE RF radiation Exposure Statement Caution :
Place the product at least 20cm from nearby persons.
Replacement of a battery with an incorrect type that can defeat a
safeguard
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery,that can result in an explosion;
Leaving a battery in an extremely high temperature surrounding environment
that can result in an explosion ammable liquid or gas; flammable liquid or gas
.
Canada, industry Canada (IC) Notices
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits.
The Wireless Device should be used in such a manner such that the potential
for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF
Exposure limits under mobile exposure conditions.
(antennas are greater than 20cm from a person’s body).
About device information
You can press the top and middle buttons at the same time to get label
information.
FCC ID: 2AF82-EP0400 IC: 23322-EP0400 HVIN:EP0400
Surface Preparation for Tape Application
Most substrates are best prepared by cleaning with a 50:50 mixture of
isopropyl alcohol (IPA) and water* prior to applying Tapes. There are
exceptions!
Exceptions to this general procedure that may require additional surface
preparation include:
- Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or greasdrom a surface and should be followed by cleaning with IPA/water.
- Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt omxidation and can increase surface area to improve adhesion.
- Porous Surfaces:Most porous and fibered materials such as wood, particleboard, concrete etcneed to be sealed to provide a unified surface.
- Unique Materials:Special surface preparation may be needed for glass and glass-like materials,copper and copper containing metals and plastics or rubber that contain components thatmigrate (e.g. plasticizers).
General Procedure
-
To obtain optimum adhesion, the bonding surfaces must be well unified, clean and dry.
Typical surface cleaning solvents are IPA/ water mixture (rubbing alcohol) or heptane. * (Steps A and B) -
Bond strength is dependent upon the amount of adhesive-to- surface contact developed.
Firm application pressure develops better adhesive contact and helps improve bond strength.
(Steps C and D) Generally, this means that the tape should experience at least 15 ps{100 kPa) in roll down or platen pressure. -
After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% fter 24 hours and 100% after 72 hours.
In some cases, bond strength can be increased and ultimate bond strength can be achieved more quickly by exposure of the bond to elevated temperatures. (e.g. 150°F [66°C] for 1 hour).
| | |
---|---|---|---
Step A:
Solvent wipe| Step B:
Wipe dry| Step C:
Apply tape to surface| Step D:
Roll finished joint
NOTE : These cleaner solutions contain greater than 250 g/l of volatile
organic compounds (VOC).
Please consult your local Air Quality Regulations to be sure the cleaner is
compliant.
When using solvents, be sure to follow the manufacturer’s precautions and
directions for use when handling such materials.
The product contains a coin/button cell battery.
Do not ingest battery, Chemical Burn Hazard.
Keep batteries out of reach of children.
Brand: Qbic
Model: EP-0400
Input: 3V 10mA
Operating Temperature: 0-40°C
Battery information:
Model : CR2450
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Qbic Technology Co.,Ltd.26F.-12,No.99.Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, Taiwan(R.O.C)
TEL:886-2-2697-2000 FAX:886-2-2697-2868
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>