ideal lux Audi-20 SP1 Pendant Light 1Lt in Smoked Transparent Glass Instruction Manual

ideal lux Audi-20 SP1 Pendant Light 1Lt in Smoked Transparent Glass

Product Specifications

• Model: Audi-20 SP1
• Power: E27 max 1 x 60W
• Voltage: 220-240V, 50/60Hz
• Barcode: 8021696016931
• Energy Efficiency Class: E

Installation

1. Ensure installation is carried out by a qualified electrician.
2. Follow the assembly instructions in numerical order.
3. Refer to the user manual for detailed installation steps.

Replacing Light Source

This product is equipped with a replaceable light source. Follow these steps to replace the light source:

1. If the light source needs replacement, ensure the power is disconnected.
2. Unscrew the existing light source carefully.
3. Insert the new light source, ensuring it is securely fitted.
4. Reconnect the power and test the light.

Suspension lamp

E27 max 1 x 60W / 220~240V 50/60Hz
8021696016931 TRASPARENTE

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN. THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

CAUTION

This product is provided with a light source with efficient energy class of:

• Energy Efficiency Class
• 8021696101347 E
• 8021696101354 E

ASSEMBLY

LEGENDA ICONE

• Replaceable light source by an end-user.
• Replaceable LED light source by an end-user.
• Replaceable light source by authorized personnel only.
• Upon the end of the life of the light source, the whole product will be replaced.
• Replaceable control gear by an end-user.
• Replaceable light source by authorized personnel only.
• Upon the end of the life of the control gear, the whole product will be replaced.

Safety Instructions

1. This fitting is produced and tested by the strictest European safety standards EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires are not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class | Electrical safety guaranteed by the main insulation and additional protective conduct- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
23. Class III Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire is not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com

References

• The domain name Electrician.LA is for sale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>