CR-10 SE 3D Printer Creality Store User Manual

CR-10 SE 3D Printer Creality Store

Product Information

Specifications

• Model: CR-10 SE
• Version: V1.0
• Printer Type: 3D Printer
• Firmware Upgrade Method: Creality Cloud OTA for WiFi firmware; Website download for equipment firmware
• After-Sales Service Contact: +86 755 3396 5666, cs@creality.com

About the Printer

Parts List

Product Usage Instructions

Assembly Procedure

Light Stand Installation

1. Assemble the light stand and attach it to the gantry frame.
2. Connect the LED light cable.
3. Place the LED light cable into the profile groove as shown in the diagram and secure it with sealing tape.

Gantry Frame Assembly Installation

1. Place the gantry frame assembly in the base slot.
2. Lock it using four M5x45 screws aligned with the holes from the bottom.

Display Screen Component Installation

1. Place the screen bracket on the side of the right profile and tighten it with three M4X25 screws.
2. Align and lock the display screen in place.
3. Connect the display wiring.

Installation of the Material Rack Assembly and Wire Clip

1. Install the material rack and barrel according to the diagram.
2. Secure the material rack assembly to the profile by pressing it down firmly.
3. Clamp the wire clip to the back panel of the X-axis Motor.

Equipment Wiring

1. Connect the power cable to the extruder adapter board and X-axis motor.
2. Connect the filament detection line following label instructions.
3. Insert and connect the extruder cable as per instructions.
4. Connect the Z-axis motor.

Pulley Tightness Adjustment

Before starting up, please check the tightness of the pulley.
Z axis pulley adjustment:
Gently dial the pulley to check whether it is idling or stuck. If this phenomenon occurs, use an open-end wrench to adjust the hexagonal eccentric isolation column to make it rotate smoothly.

About the Power-on Guide and User Interface

Power-on guide

Tips:

If any abnormalities occur during the self-check process, please refer to the FAQ to check for possible machine malfunctions; Alternatively, scan the QR code for “fault reporting” to report the machine issue and seek assistance from the after-sales service for problem resolution.

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/firmware UI published on the official website.

4.2 About the User Interface

Use the preparation interface to set functions such as axis movement, temperature control for filament extrude/retract, and model fan cooling.

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/-firmware UI published on the official website.

First Printing

Filament Loading

LAN printing

• Install Creality Print slicing software by opening the random data on the USB flash disk.
• Log in to the official website to download for installation：https://www.crealitycloud.com/software-firmware/software?type=7

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/firmware UI published on the official website.

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/firmware UI published on the official website.

USB flash disk Printing

The current interface is for reference only. Due to the continuous upgrading of functions, it shall be subject to the latest software/firmware UI published on the official website.

Note:

1. For details on using the software, please refer to the slicing software user manual on the USB flash disk.
2. Saved files must be placed in the root directory (not a subdirectory) of the USB flash disk.
3. It is recommended to use Latin alphabet, numbers, and common characters for the file names.
4. Do not insert or remove the USB flash disk during the printing process.

Functional Specification

• Auto extrude
• Auto retract

Equipment Maintenance

Platform plate removal and maintenance

1. a. When printing is finished, wait for the platform plate to cool before removing the printing platform with the model attached;
   b. Slightly bend the platform with both hands to separate the model from the platform.

2. If there are residual filaments on the platform plate, scrape them off lightly with a blade and print again.

3. If the first layer of the model is not properly glued, it is recommended to apply solid adhesive evenly on the surface of the platform plate before preheating for printing

Maintenance of screw rod and guide rail

Regularly lubricate and maintain the screw rod and guide rail areas with purchased lubricating grease.

Equipment Parameters

Circuit Wiring

Due to the differences between different machine models, the actual objects and the images can differ. Please refer to the actual machine. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

Frequently Asked Questions (FAQ)

Q: How do I upgrade the firmware of the CR-10 SE?

A: You can upgrade WiFi firmware via Creality Cloud OTA or equipment firmware by downloading from https://www.creality.com and following the instructions provided.

Q: Where can I find tutorials on after-sales service for the CR-10 SE?

A: Visit https://www.crealitycloud.com/product, click on Products, select your model, and then click Related to view tutorials. You can also contact after-sales service at +86 755 3396 5666 or email cs@creality.com.

References

• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
• [Official] Creality Product Center - Compare different 3D printers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>