stuv AW1300412900 Fireplace Frame Instruction Manual

stuv AW1300412900 Fireplace Frame

Product Information

Specifications

• Dimensions:
  • Model AW1300412900: A 31 3/16, B 24 1/16
  • Model AW1300413300: A 35 1/8, B 27 1/4
  • Model AW1300411300: A 39 1/16, B 18 3/4
  • Model AW1300413400: A 46 15/16, B 24 1/16

Product Usage Instructions

Installation

1. Before Installation:
   Remove finishing trims from around the hearth. Vertical trims are no longer required.

2. Step 1:
   Slide the frame onto the tabs opened earlier. Ensure the frame is the correct size (indicated by an arrow on the back).

3. Step 2:
   Avoid screwing the thin edge frame into the fireplace. It is supported by hooks.

4. Top Installation:
   Using a hammer, form hooks with the tabs over the frame. Do not screw the thin edge frame in the fireplace as it is held by the hooks.

5. Bottom Installation:
   Replace the horizontal finishing trims and adjust to the last slot for maximum opening.

6. Final Steps:
   Cut the cement board in one piece to prevent cracking. Place the board around the thin edge frame. Finish with metal trims and high-temperature plaster or non-combustible material.

FAQ

Q: Can I attach the frame using screws in the fireplace?

A: No, do not screw anything into the fireplace. The frame should be supported by hooks and finishing trims.

Q: Is the frame designed to bear weight?

A: No, the frame is not a structural component and is not designed to bear weight.

Q: What tools are required for installation?

A: Tools required include a flat screwdriver, hammer, level, and impact driver with a T25 Torx bit.

REQUIRED TOOLS

IMPORTANT
This document is an additional manual to the Stûv 21 installation manual. For a successful installation, it is important to follow these instructions carefully. Look for this symbol in the Stûv 21 installation manual to know when to refer to this manual.

RECOMMENDATIONS

ATTENTION

1. The painting on the frame is fragile. Handle with care and be careful with accessories and tools that could damage the paint.
2. Follow all recommendations written in the Stûv 21 instruction manual.
3. Install the frame before the wall finishes. It will facilitate the cutting of the finishing material to the right dimensions.
4. The ideal position is with a 3/16’’ protrusion at the front. This prevents the heat from getting too close to the wall and hides any imperfections in the brickwork.
5. This frame is not a structural component. It is not designed to bear weight.
6. The holes in the frame’s wing pieces are not for attaching the frame. Never screw anything in the fireplace.

NOTE
This frame has been designed to offer you maximum comfort and safety. If however, you are in any way dissatisfied with the product, please contact your reseller.

DIMENSIONS

FINE FRAME 3’’ (for finishing material ½’’ à 1 ½’’)

Outside dimensions

3’’

| CODE| A| B|

Frame thickness

---|---|---|---|---
21- 85| AW1300412900| 31 3/16”| 24 1/16”| 5/32”
21-95| AW1300413300| 35 1/8”| 27 1/4”| 5/32”
21- 105| AW1300411300| 39 1/16”| 18 3/4”| 5/32”
21- 125| AW1300413400| 46 15/16”| 24 1/16”| 5/32”

FINE FRAME 4’’ (for finishing material 1 ½’’ à 2 ½’’)

Outside dimensions

4’’

| CODE| A| B|

Frame thickness

---|---|---|---|---
21- 85| AW1300410900| 31 3/16”| 24 1/16”| 5/32”
21-95| AW1300411000| 35 1/8”| 27 1/4”| 5/32”
21- 105| AW1300411100| 39 1/16”| 18 3/4”| 5/32”
21- 125| AW1300411200| 46 15/16”| 24 1/16”| 5/32”

INSTALLATION

• Step 1
  Remove finishing trims from around the hearth. Both vertical trims are no longer required.

• Step 2
  Locate all four precut slots on the front of the unit around the hearth and with the help of a flat screwdriver bend them to a 90° angle.

• Step 3
  Slide the frame onto the 4 tabs opened earlier. Make sure the frame is on the right side (size indicated by an arrow on the back of the frame).

• Step 4
  Using a level, check that the frame is flush with the Stûv 21 hearth opening .

• Step 5
  Using a hammer, form hooks with the tabs over the frame. Do not screw the thin edge frame in the fireplace. The frame is held by the hooks.

• Step 6
  Replace the horizontal finishing trims and adjust to the last slot for maximum opening.
  NOTE
  Only the finishing trims and wall framing should be used to affix fi-nishing materials. Do not drill any screws into the fireplace.

• Step 7
  Cut the cement board in one piece to prevent it from cracking. Place the board around the thin edge frame.

• Step 8
  Finish the installation with metal trims and high-temperature plaster or any other noncombustible finishing material.

Contact Information

And manufactured in North America by:

• Stûv America Inc. – Canada
• stuvamerica.com
• 34, Boulevard de l’Aéroport Bromont, QC Canada J2L 1S6
• 1-514-396-3463 | 1-866-487-7888

9310400013 | November 2023

References

• Stoves and fireplaces | Wood heating | Stûv America

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>