ideal lux 8I284460 Suspension Lamp Instruction Manual
- June 17, 2024
- ideal lux
Table of Contents
ideal lux 8I284460 Suspension Lamp
Product Specifications:
- Brand: IDEAL LUX
- Model: Craft SP
- Power: LED 37W
- Voltage : 220-240V, 50/60Hz
- Energy Efficiency Class: F
- Light Source: 23.1W, 24V DC
Product Usage Instructions
Installation:
- Ensure the lighting fixture is installed by a qualified electrician.
- Follow the assembly instructions provided in numerical order.
- For safety, always disconnect the power supply before installation or maintenance.
- Use appropriate fixtures and accessories for mounting, adhering to regulations.
Light Source:
The product is equipped with a replaceable LED light source that can be
replaced by the end-user.
Maintenance:
If the external power cable is damaged, it should only be replaced by the
manufacturer, retailer, or a qualified electrician.
Safety Instructions:
- Complies with European safety standards EN 60 598-1.
- Always follow local regulations for proper disposal methods.
- Installation must be carried out by a qualified electrician in some regions.
- Avoid looking directly at the light source to prevent eye strain.
- Unplug the fixture before any maintenance or installation procedures.
Frequently Asked Questions (FAQ):
-
Q: Can the LED light source be replaced by the user?
A: Yes, the LED light source in this product is replaceable by the end-user. -
Q: What is the energy efficiency class of this product?
A: The energy efficiency class of this product is F. -
Q: What voltage does the product operate on?
A: The product operates on a voltage range of 220-240V at 50/60Hz.
IDEAL LUX s.r.l.
- Via Taglio Destro 32
- 30035 Mirano (VE) Italy
- www.ideal-lux.com
IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
Instructions
Suspension lamp
LED 37W / 220~240V 50/60Hz – 8021696284460 LEGNO
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Assembly
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
Non-replaceable light source: at the end of its life, the lamp must be disposed.
This product is provided with a light source with efficiency energy class of:
- EAN 8021696284460
- Light Source Model CRAFT SP 3000K
- Energy Efficiency Class F
- Light Source (W) 23,1 W
- Light Source (V) 24 V DC
LEGENDA ICONE
- Replaceable light source
- Replaceable LED light source
- Replaceable light source
- Non-replaceable light source.
- Replaceable control gear
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>