ideal lux Febe-1 AP Wall Lamp Instruction Manual

: June 17, 2024
: ideal lux

Table of Contents

ideal lux Febe-1 AP Wall Lamp
Product Specifications
LED
SYMBOLE
INSTALLATION
LEGENDA ICONE
SAFETY INSTRUCTIONS
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ideal lux Febe-1 AP Wall Lamp

Product Specifications

Brand: Febe-1 AP
LED: 6W / 220~240V 50/60Hz
Available Colors and Color Temperatures:
- Antracite 3000K – 8021696250854
- Bianco 3000K – 8021696268347
- Antracite 4000K – 8021696322285
- Bianco 4000K – 8021696322292

LED

LED 6W / 220~240V 50/60Hz

8021696250854 ANTHRACITE 3000K
8021696268347 BIANCO 3000K-
8021696322285 ANTRACITE 4000K
8021696322292 BIANCO 4000K

SYMBOLE

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-2

INSTALLATION

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION.

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-3

QUALIFICATO. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-4

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-5

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE

Non-replaceable light source: at the end of its life, the lamp must be disposed.

This product is provided with a light source with efficient energy class of:

Light Source
Energy Model
Efficiency Class
Light Source (mA)
Light Source (V)

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-16

LEGENDA ICONE

Replaceable light source by an end-user.
Replaceable LED light source by an end-user.
Replaceable light source by authorized personnel only.
Non-replaceable light source. Upon the end of the life of the light source, the whole product will be replaced.
Replaceable control gear by an end-user.
Replaceable light source by authorized personnel only.
Upon end of life of the control gear, the whole product will be replaced.

SYMBOLE

ideal-lux-Febe-1-AP-Wall-Lamp-FIG-14

SAFETY INSTRUCTIONS

This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
This fitting cannot be disposed of as household waste. For disposal, information ask the local authorities about how to collect it.
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor, or by a qualified electrician.
Always isolate power before commencing installation, maintenance, or repair.
The luminaire contains certain parts which can be very hot.
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
Always tighten the screws firmly to avoid contact problems.
This fitting should only be installed indoors.
Luminaires are not suitable for recessed on normally flammable surfaces.
Luminaire is not suitable for direct mounting on normal flammable surfaces.
This fitting is only suitable for fixing the ceiling.
This fitting is only suitable for fixing the wall.
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wires so that it is longer than the chain.
Only use lamps that do not exceed the maximum specified wattage.
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
Not protected.
Protected against solid objects greater than 50 mm.
Protected against solid objects greater than 12 mm.
Protected against solid objects greater than 2,5 mm.
Protected against solid objects greater than 1mm.
Dust protected.
Protected against dust infiltration.
Not protected.
protected against vertically falling water drops.
protected against water drops falling with a maximum angle of 15° to the vertical axis.
Protected against rain.
Protected against splashing water.
Protected against water jets.
Protected against strong water jets.
Protected against temporary immersion.
Protected against prolonged immersion.
Luminaire was not suitable for covering with thermally insulating material.
Caution, risk of electric shock.
Do not stare at the operating plant source.

FAQ

Frequently Asked Questions

Q: Can I replace the light source myself?
- A: Yes, both the light source and the LED light source are replaceable by end-users.
Q: What should I do if the external power cable is damaged?
- A: The external power cable must be replaced exclusively by the manufacturer, retailer, or a qualified electrician.
Q: Are there any specific safety instructions I should be awareof?
- A: Yes, always disconnect the power supply before starting any installation or maintenance work. Additionally, this product contains parts that can become hot during operation, so handle with care.

CONTACT

IDEAL LUX s.r.l.