ideal lux YOKO PT LED Floor Lamp Instruction Manual
- June 17, 2024
- ideal lux
Table of Contents
ideal lux YOKO PT LED Floor Lamp
Product Information
Yoko PT LED 16W
- Input Voltage: 220-240V, 50/60Hz
- Model Numbers: 8021696258874 (BIANCO), 8021696258904 (NERO)
- Manufacturer: IDEAL LUX s.r.l.
- Address: Via Taglio Destro 32, 30035 Mirano (VE) Italy
- Website: www.ideal-lux.com
Specifications
- Light Source: LED 16W
- Energy Efficiency Class: F
- Light Source Power: 9.4W
- Light Source Voltage: 12V DC
Product Usage Instructions
Installation
The lighting fitting should be installed by a qualified electrician. Follow the assembly instructions by reading the numerical progression.
Light Source Replacement
This product contains a light source that can be replaced by an end-user. The LED light source is also replaceable by an end-user.
Safety Instructions
- Always disconnect the power supply before installation or maintenance.
- Avoid looking directly at the light source.
- Ensure the external electrical cable is replaced only by the manufacturer, retailer, or a qualified electrician if damaged.
- Use appropriate fixing accessories and comply with regulations for replacement parts.
- Avoid disassembling the LED light source as it is not user-replaceable.
Frequently Asked Questions
Q: Can the LED light source be replaced by anyone?
A: Yes, the LED light source is replaceable by an end-user.
Q: What should I do if the external electrical cable is damaged?
A: The external electrical cable should be replaced only by the manufacturer, retailer, or a qualified electrician.
Q: How should I ensure safety during installation?
A: Always disconnect the power supply before starting any installation or maintenance procedures.
Dimension
LED 16W / 220~240V 50/60Hz
- 8021696258874 BIANCO
- 8021696258904 NERO
Warning
- FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION.
- QUALIFICATIONS. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
LEGENDA ICONE
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Non-replaceable light source. Upon end of life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will he replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
- Via Taglio Destro 32
- 30035 Mirano (VE) Italy
- www.ideal-lux.com
IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>